• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Fabrication and Mechanical Testing of Ultralight Folded Lattice-Core Sandwich Cylinders

    2020-05-22 08:02:20WanxinLiQingZhengHualinFanBinJi
    Engineering 2020年2期

    Wanxin Li, Qing Zheng*, Hualin Fan*, Bin Ji

    a State Key Laboratory for Disaster Prevention and Mitigation of Explosion and Impact, Army Engineering University of PLA, Nanjing 210007, China

    b Research Center of Lightweight Structures and Intelligent Manufacturing,State Key Laboratory of Mechanics and Control of Mechanical Structures,Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

    c Aerospace System Engineering Shanghai, Shanghai 2011089, China

    Keywords:

    A B S T R A C T In this research, two novel folded lattice-core sandwich cylinders were designed, manufactured, and tested. The lattice core has periodic zigzag corrugations, whose ridges and valleys are directed axially or circumferentially.Free vibration and axial compression experiments were performed to reveal the fundamental frequency, free vibration modes, bearing capacity, and failure mode of the cylinder. A folded lattice core effectively restricts local buckling by reducing the dimension of the local skin periodic cell,and improves the global buckling resistance by enhancing the shear stiffness of the sandwich core. The cylinders fail at the mode of material failure and possess excellent load-carrying capacity. An axially directed folded sandwich cylinder has greater load-carrying capacity, while a circumferentially directed folded sandwich cylinder has higher fundamental frequencies.These two types of folded lattices provide a selection for engineers when designing a sandwich cylinder requiring strength or vibration. This research also presents a feasible way to fabricate a large-dimensional folded structure and promote its engineering application.

    1. Introduction

    Carbon-fiber-reinforced composite (CFRC) anisogrid stiffened cylinders and lattice truss sandwich cylinders are lightweight,but have high load capacity and great rigidity. In recent years,these structures have been increasingly accepted for use in aerospace applications. Vasiliev et al. [1] reviewed the development of anisogrid composite lattice structures and their application in aerospace. Lovejoy and Schultz [2] developed the CFRC flutedcore sandwich cylinder,which may be used in large-diameter cryogenic tanks for rockets. Researchers from China [3-11] developed CFRC lattice-core sandwich cylinder technology,and demonstrated that these structures are stronger and stiffer than a typical stiffened cylinder. They also developed cylinders with a corrugated core or bi-directional corrugated core [12,13], and concluded that the corrugation design enlarges the node area and improves the shear strength. Sun et al. [14] and Li and Fan [15] developed a multi-failure criterion for both lattice-stiffened and lattice-core sandwich cylinders. Recently, Li et al. [16] and Wu et al. [17]designed and made hierarchical anisogrid cylinders,which possess excellent mechanical performance.

    Fold-core sandwich structures,which are regarded as a promising alternative to conventional lightweight honeycomb sandwich structures, have many potential applications in aerospace, such as for the aircraft fuselage barrel, rocket interstage, and cryogenic tank. Cai et al. [18] discussed foldable structures in a cylindrical shape via the quaternion rotation sequence method and assessed the rigid foldability. Zhou et al. [19] developed a geometrical design protocol for a cylindrical fold-core sandwich structure based on the vertex method,and demonstrated that fold-cores outperform honeycomb cores in axial compression and radial crush but have a lower radial stiffness when subjected to internal pressure. Xiong et al. [20] and Yang et al. [21] fabricated sandwich cylinders with longitudinal and circumferential corrugated cores with a diameter of 116 and 142 mm, respectively, and demonstrated that cylindrical shells with longitudinal cores have better energy absorption ability than those with circumferential cores.Liu et al. [22] fabricated a CFRC cylindrical fold-core sandwich structure with a diameter of 156.6 mm,and demonstrated through theory and tests that its load-bearing capacity is several times higher than the traditional grid-stiffened cylinder. According to this research, the most important failure modes of these cylinders are local buckling and face crushing, which were frequently observed during the experiments.

    In the present research, two novel CFRC folded lattice-core sandwich cylinders are designed. Their fabrication methods are put forward,and free vibration and axial compression tests are carried out to investigate their mechanical properties.

    2. Topology design of a folded lattice-core sandwich cylinder

    The sandwich cylinder includes two carbon-fiber-reinforced polymer(CFRP)skins and a lattice-core layer composed of cylindrical folded cells.The direction of the folded core has contrary effects on the strength and rigidity.Therefore,it is important to design the folded core properly according to the different load conditions.For load-bearing engineering structures,the folded core needs to have a higher strength and rigidity in the axial direction,while for structures that need a higher free vibration frequency, the folded core should possess high stiffness in the circumferential direction.

    To meet the requirements of different applicative demands,two sandwich cylinders are designed: an axially directed folded sandwich cylinder(AFSC)and a circumferentially directed folded sandwich cylinder (CFSC). In the AFSC, the core is formed with an axially directed folded lattice cell, which periodically repeats both circumferentially and longitudinally along the cylindrical shell surface.In the CFSC,the core is formed with a circumferentially directed folded lattice cell.

    2.1. Axially directed folded lattice cell

    The topology of the axially directed folded lattice cell is illustrated in Fig.1[23].Six parameters are defined in the flat unit cell[23]: a1, a2, b1, b2, φ1, and φ2, with the stipulation that a1< a2,b1φ2,where a and b are the creases of straight lines and curves,φ is the angles at which the creases are folded,as shown in Fig. 1(a) [23]. Seven parameters are defined in the folded unit cell: three dihedral angles which folded by plane faces, θA, θMZ,and θVZ, and four edge angles which folded by creases, ηMA, ηMZ,ηVA, and ηVZ, as shown in Fig. 1(b) [23]. Three parameters are defined in the front projection:the center angles of related vertices ξ,ξa2,and ξb1,where the vertices lie along the arc of radius R1and R2(Fig. 1(c)) [23]. Based on triangle geometry and projected side lengths, it can be concluded that this structure has only a single degree of freedom(DOF).The relationships among these geometrical parameters have been deduced by Gattas et al. [23] and are listed in the Appendix A.In this research,the designed axially directed folded lattice is folded out of CFRC cloth with a1=12.774 mm,a2=16.484 mm, b1=23.094 mm, b2=25.240 mm, φ1=69.295°,φ2=58.859°, ηMA=90°, ηVA=94°, ηMZ=120°, ηVZ=90°, R1=311 mm,and R2=301 mm.

    2.2. Circumferentially directed folded lattice cell

    The topology of the circumferentially directed folded lattice cell is illustrated in Fig. 2 [23]. Unlike the axially directed folded cell,according to the Kawasaki-Justin theorem [23], it is not a flatfoldable pattern. Furthermore, eight parameters are defined in the flat unit cell:a, w, bl, bs, φl(shuí), φs, φm, and φ, with the stipulation that bl

    In the same way as described for the axially directed folded cell,ηAand ηZare the edge angles. Two parameters are defined in the front projection: the half center angles of related vertices ζ and ζk,where the vertices lie along the arc of radius R3and R4,as shown in Fig.2[23].It also has a single DOF.The relationships among the geometrical constants are deduced and given by the following:

    Fig. 1. The axially directed folded lattice cell. (a) Crease pattern and constants; (b) configuration variables; (c) front (r-θ) projection. r is the polar axis; θ is the polar angle[23].

    Fig.2. The circumferentially directed folded lattice cell.(a)Crease pattern and constants;(b)folded configuration;(c)side(r-θ)projection.ζ is half the angle of bl side;x is the axis orthogonal to the ridge and the valley [23].

    The coordinates of the controls points are given by the following:

    where j is the control point number in the direction of x; rcis the radius of the arc where the control point is located.

    where θcis the angle of control point in side(r-θ)projection;i is the control point number in the direction of θ.

    where xcis the length orthogonal to the ridge and the valley in the crease pattern.

    In this research, the designed circumferentially directed folded lattice is folded out of CFRC cloth with a=12.10 mm,bl=32.14 mm, bs=35.36 mm, w=2.5 mm, φ=51°, ηA=90°,ηZ=126°, ζ=3°, ζk=0.92°, R3=301 mm, and R4=311 mm.

    3. Fabrication

    In this research,the diameter of all the cylinders is 625 mm and the height is 375 mm; these are close to the dimensions of Kim’s stiffened cylinder[24],which is the reference for the design.Compared with Xiong’s cylinder[20],the diameter is four times larger,resulting in a more difficult manufacturing process.Two sandwich cylinders were fabricated with the two types of folded lattice cores designed above,as shown in Fig.3.The designed mass is 3.86 kg for the AFSC and 3.81 kg for the CFSC.T700/Epoxy-resin carbon fibers were applied to fabricate the cylinder. The tensile strength of the carbon fiber is 4300 MPa and the Young’s modulus is 240 GPa.

    3.1. The axially directed folded sandwich cylinder

    The fabrication process of the AFSC is shown in Fig. 4. The process includes four main steps: manufacturing the fold-core by the hot-pressing method, manufacturing the inner skin, adhering the fold-core and inner skin, and manufacturing the outer skin.

    When manufacturing a fold-core, a metallic mold is first premachined according to the folded lattice geometry, as shown in Fig. 3(a). The mold is composed of two parts: a convex part and a concave part. The central angle of the molds is 60°. A preprepared 1 mm thick prepreg lay-up of [0°/90°/90°/0°]s(s represents symmetry lay-up)is put into the concave part and manually pressed tightly to prevent the fracture of fiber; next, the convex part is clenched together with the concave part, and a hot-press molding technique is applied to form six pieces of AFSC lattice with a thickness of 10 mm, respectively. The six pieces are assembled together in a subsequent process to form an integral lattice core.To ensure the continuity and integrity of the assembly, both parts of the metallic mold should have high precision, and the irregular edges of the lattice should be corrected carefully after demolding.

    Fig. 3. Two folded lattice cores. (a) Axially directed folded lattice; (b) circumferentially directed folded lattice.

    Fig. 4. Manufacturing process of the CFRC AFSC. (a) The fold-core made by the hot-pressing method; (b) the inner skin is made by filament winding and lay-up placing;(c) adhering the fold-core and skins; (d) the completed cylinder after finishing the outer skin.

    The manufacture of the inner skin follows this process:winding the filament [0°], placing the lay-up [90°/90°], winding the filament [0°], placing the lay-up [90°/90°], and continuing to repeat the above operations.First,the filament is wound circumferentially to form the first thin layer; next, two prepreg layers with a fiber direction along the axis of the cylinder are placed on the first layer to form the second and third thin layers. Following this, the filament is wound circumferentially outside the prepreg layers.These operations are repeated until the skin thickness reaches 1 mm, so the fiber mode of the inside skin is [0°/90°/90°/0°]s. The six premade pieces of lattice are then adhered onto the surface of the inner skin by resin to form the core of the sandwich cylinder, as shown in Fig. 4(c).

    In the manufacture of the outer skin, a prefabricated thin CFRP sheet is first adhered to the core to ensure the bonding strength between the core and outer skin.Next,the process is followed until the thickness of the outer skin reaches 1 mm:winding the filament[0°],placing the lay-up[90°/90°],winding the filament[0°],placing the lay-up [90°/90°], and repeating the above operations. Finally,the sandwich cylinder is cured at 100 °C for 2 h, at 150 °C for 6 h, and then gradually cooled to room temperature in 2 h. After demolding, the cylinder is as shown in Fig. 4(d), and its fiber content is about 40%.

    3.2. The circumferentially directed folded sandwich cylinder

    The fabrication process of the CFSC is the same as that of the AFSC, as shown in Fig. 5; the mold for the fold-core is as shown in Fig. 3(b).

    4. Free vibration behaviors

    Through the force-hammer excitation method, free vibration experiments were performed on the two cylinders under endfree boundary conditions at the State Key Laboratory of Mechanics and Control of Mechanical Structures.

    During the test, the cylinder was placed on the rubber ring to simulate free vibration, as shown in Fig. 6(a). The test equipment contains a power hammer, a modal analysis system, a charge amplifier, and three acceleration sensors. The cylinder, simplified as an n-DOF system, is impacted at one point by a hammer, and its response is measured by accelerometers at three fixed points.Moving the excitation point from point 1 to point 64 and keeping the response points fixed, the system’s frequency response function matrix can be measured;the natural frequencies and vibration modes can then be obtained.

    Fig. 5. The manufacturing process of the CFRC CFSC. (a) A fold-core made by the hot-pressing method; (b) inner skin made by filament winding and lay-up placing;(c) adhering the fold-core and skins; (d) the completed cylinder after finishing the outer skin.

    Fig. 6. Free vibration test (a) scheme and (b) frequencies and damping of the cylinders.

    Fig. 7. Free vibration modes of (a) the AFSC and (b) the CFSC. Freq: frequency; Damp: damping.

    The first 10 orders of natural frequencies are displayed in Fig. 6(b), and the modes are depicted in Fig. 7. For the first mode,the cylinder vibrates circumferentially from a circle to an oval, as shown in Fig. 7. Along the longitudinal direction, the cylinder has an identical motion phase. The second mode has an identical frequency as the first order, while their vibration shapes are along two orthogonal directions. The third and fourth orders have two circumferential waves and one longitudinal wave. The motions of the two cylinder ends have a phase difference of 180°. After that,the mode shape of the cylinder extends to form a triangular shape and a rectangular shape with higher frequency,as shown in Fig.7.The rule of the lobe development is consistent with that of a uniform thin-walled cylinder.

    As compared in Fig. 6(b), the first-order natural frequency is 66.01 Hz for the AFSC and 84.28 Hz for the CFSC.All the natural frequencies of the CFSC are higher than the corresponding frequencies of the AFSC, indicating that the CFSC has greater circumferential rigidity and is preferable for the design of vibration control.

    5. Axial compression behaviors

    Fig. 8. (a) Compression experiment and (b) displacement curve for the CFRC AFSC.

    The axial compression behaviors of the cylinders were tested on an American brand of testing machine(MTS)universal test system at a loading rate of 0.2 mm·min-1, as shown in Fig. 8(a). Twelve strain rosettes were adhered to the outer surface of the cylinder,as shown in Figs. 6(a) and 8(a). Each strain rosette contains three gauges to measure the strains directed along the cylinder (90°),around the cylinder (0°), and along the diagonal direction (45°).

    The compression curve of the AFSC is displayed in Fig. 8(b). As the load increased, a small cracking sound caused by the debonding between the skin and the core could be heard near the end of the elastic deformation phase. When the displacement reached 3.28 mm, the load reached its peak value, 293.4 kN. Brittle failure then occurred in the cylinder, and the load dropped abruptly. The axial compression rigidity was 123.5 kN·mm-1. The measured strains are displayed in Fig. 9. At failure, the maximum strain appeared at the lower end; its value was 4750 με.

    The strain distribution for a cylinder is not ideally uniform,and failure always initiates somewhere with defects or stress concentrations. For the AFSC, the failure was located near the ends and the fractures extended around the cylinder, as shown in Fig. 10.No buckling was observed in the test, and the cylinder failed with facesheet crushing.

    The compression curve of the CFSC is displayed in Fig. 11(b).A small cracking sound caused by the debonding between the skin and the core was again heard near the end of the elastic deformation phase.Subsequently,the cylinder approached its peak force when the displacement was 2.79 mm, and then entered into post-failure deformation, as shown in Fig. 11. Therefore, the CFSC has better ductility than the AFSC under axial compression. The failure load of the CFSC was 191.0 kN,which is much smaller than that of the AFSC. The axial compression rigidity was 113.4 kN·mm-1, which is also smaller than that of the AFSC.

    In comparison with Kim’s stiffened CFRC cylinder with a diameter of 625 mm,height of 368 mm,and weight of 3.24 kg[25],the failure load of the CFSC is about 1.5 times higher, as shown in Fig. 11(b), while that of the AFSC is about 2.5 times higher. The axial rigidities of both the CFSC and AFSC are much higher.

    The measured strains are displayed in Fig. 12. At failure, the maximum strain appears at the upper end with a value of 3949 με, a little smaller than the value of the AFSC. The failures are located at one third of the height from the lower end,and the fractures extend around the cylinder,as shown in Fig.13.The cylinder also fails with facesheet crushing.

    The two cylinders have an identical facesheet, such that the peak force depends on the direction of the folding. The shear modulus is much higher along the ridge and the valley than orthogonal to the ridge and the valley, as is the bending rigidity.These contributions to the integral rigidity and the shear rigidity improve the global buckling resistance induced by bending or core shear. The corrugation also has a greater axial compression strength along the ridge and the valley than orthogonal to the ridge and the valley. When the ridges are axially directed, all these factors make important contributions to the load bearing. When the ridges are circumferentially directed, the wave core makes little contribution to the axial load bearing. Therefore, the AFSC is preferable in terms of strength design.

    Fig. 9. Strain curves of the CFRC AFSC.

    Fig. 10. Failure mode of the CFRC AFSC. (a,b) Facesheet crushing at upper edge;(c,d) facesheet crushing at lower edge.

    6. Discussion

    6.1. Mechanical behaviors

    In comparison with a corrugated-core sandwich cylinder[25],a folded sandwich cylinder transforms the straight corrugation into two types of zigzag corrugation, as shown in Fig. 14. This change in geometry alters the mechanical performance.

    According to the structural characteristics, straight corrugation has the highest axial rigidity, and can have a high mass efficiency under axial compression. By transforming the straight corrugation into zigzag corrugation,the axial rigidity is redistributed in the circumferential direction;thus, the axial rigidities of the three structures are ordered as follows, from largest to smallest: straight corrugation, axially directed folded lattice, and circumferentially directed folded lattice. The axial load-bearing ability is positively correlated with the axial rigidity,so the failure loads of these three structures under axial compression are ordered as follows, from largest to smallest:straight corrugation,axially directed folded lattice,and circumferentially directed folded lattice,when they fail at the same mode,material yielding,or buckling.As shown in the test result,the failure load of the sandwich cylinder with a core of axially directed folded lattice is 293.4 kN, so it is much stronger than the cylinder with a core of circumferentially directed folded lattice,whose failure load is 191.0 kN.With higher axial rigidity,the welldesigned sandwich cylinder with a straight corrugation core,diameter of 625 mm,height of 375 mm,and weight of 3.24 kg has a failure load of 415.6 kN, which is much higher than those of the two fold-core cylinders [25].

    Fig. 11. (a) Compression experiment and (b) displacement curve for the CFRC CFSC.

    Fig. 12. Strain curves for the CFRC CFSC.

    Fig. 13. Failure mode of the CFRC CFSC. (a,b) Facesheet crushing at outer skin;(c,d) facesheet crushing at inner skin.

    Fig. 14. Transformation of straight corrugation into zigzag corrugation.

    The circumferential rigidities of the three structures have an opposite relationship with the axial rigidities, as follows: circumferentially directed folded lattice > axially directed folded lattice>straight corrugation.Their free vibration frequencies have complex connections with both the axial rigidity and circumferential rigidity, but the frequencies are more closely connected with the weak rigidity when the anisotropy of rigidity is strong.Furthermore, for the zigzag corrugation, the shear resistance is anisotropic. The shear modulus is much higher along the ridge and the valley than orthogonal to the ridge and the valley,as is the bending rigidity. When the folded lattice is circumferentially directed, the higher shear stiffness can improve the rigidity of the sandwich shell by reducing the shear-induced deflection,which is an important contribution to the integral deflection of the sandwich structure. In addition, its bending rigidity makes a non-ignorable contribution to improve the integral rigidity.Therefore,the natural frequencies of the CFSC are much higher than those of the AFSC,as validated by the test result. It can be predicted that the cylinder with a straight corrugation core in Ref. [25] would have lower natural frequencies than both the CFSC and AFSC.

    Other than improving the fundamental frequency, there are other advantages for folded lattice-core cylinders. First, adopting zigzag corrugation can restrict the local buckling of the facesheet,while this failure mode was often observed in axial compression of the straight-corrugated-core sandwich cylinder [25]. Second,zigzag corrugation also enhances the shear resistance by increasing the bonding area compared with straight-corrugated-core cylinders, and improves the global buckling resistance. Third, the folded lattice-core sandwich has an open configuration, so the cylinders would have the property of air permeability, which can meet the requirements of some multi-function designs, especially in aerospace engineering.

    6.2. Evaluation of fabrication method

    The fabrication of the cylindrical folded lattice core in this research is easy to achieve, which might be the key to promote the engineering application of the folded core sandwich cylinder.Liu et al. [22] fabricated a CFRC cylindrical fold-core sandwich structure using the mold-pressing method and that structure has excellent mechanical properties, although the fabrication method would be limited in the case of a larger cylinder design.In the present research, the integral fold-core was split into six identical parts. Each part was manufactured by hot-pressing using metallic molds. This method is now easy to realize. Furthermore, the use of filament winding and lay-up placing to make the cylindrical facesheet is a mature technique. Therefore, the present research presents a successful and feasible way to make a largedimensional folded structure and promote its engineering application.Aspects that remain to be improved are the fiber content and the pressure control in the curing process.

    7. Conclusions

    In this research, two novel folded lattice-core sandwich cylinders with two types of cores were designed and fabricated. Their free vibration and axial compression behaviors were investigated through tests. The following conclusions were made:

    (1) The manufacturing process of the CFRC fold-core sandwich cylinder was realized through mold-pressing, filament-winding,and lay-up placing techniques. By fabricating six repeated pieces of the lattice and assembling them to form an integral core layer,it is feasible to create large-dimensional folded lattice-core cylinders.

    (2) The zigzag topology of the corrugation in the folded lattice enhanced the shear resistance of the core by increasing the bonding area with the skins, and improved both the global and local buckling resistance. The AFSC and CFSC have different advantages in terms of mechanical properties due to their geometric characteristics, resulting in wider potential applications in engineering.

    (3) Both the AFSC and CFSC freely vibrate like typical short sandwich cylinders, with the modes changing from oval, to triangular, to quadrangular. The CFSC has higher circumferential rigidity and shear stiffness, leading to higher natural frequencies than the AFSC,so the CFSC is preferable when designing structures with strict frequency requirements.

    (4)In the axial compression test,both the AFSC and CFSC failed at the facesheet crushing mode; however, their bearing capacities differed because of the different folding directions of their cores.Due to its higher rigidity in the axial direction, the AFSC has a greater peak load under compression, so it is preferable in terms of strength design.

    Acknowledgement

    Support from the National Natural Science Foundation of China(11672130 and 11972184), the State Key Laboratory of Mechanics and Control of Mechanical Structures (MCMS-0217G03), and Aerospace System Engineering Shanghai are gratefully acknowledged. Help from Professor Tong Wang in vibration testing is gratefully acknowledged.

    Compliance with ethics guidelines

    Wanxin Li, Qing Zheng, Hualin Fan, and Bin Ji declare that they have no conflict of interest or financial conflicts to disclose.

    Appendix A

    The relationships among the geometrical constants of the axially directed folded lattice were deduced by Gattas et al. [23] and were used to design the cylinder; they are cited below:

    国产亚洲精品久久久久久毛片| 天堂网av新在线| 国产麻豆成人av免费视频| 老汉色av国产亚洲站长工具| 国产三级在线视频| 国产视频一区二区在线看| 日韩精品青青久久久久久| 男女下面进入的视频免费午夜| 男人舔女人的私密视频| 久久久成人免费电影| or卡值多少钱| 成人特级av手机在线观看| 一夜夜www| 欧美zozozo另类| 亚洲人成电影免费在线| 91老司机精品| 国产精品永久免费网站| 亚洲va日本ⅴa欧美va伊人久久| 亚洲一区二区三区色噜噜| 无遮挡黄片免费观看| 老汉色av国产亚洲站长工具| 搡老妇女老女人老熟妇| 热99re8久久精品国产| 国产精品永久免费网站| 白带黄色成豆腐渣| 人人妻,人人澡人人爽秒播| 最新中文字幕久久久久 | 精品国产美女av久久久久小说| 国内揄拍国产精品人妻在线| 亚洲狠狠婷婷综合久久图片| 亚洲人成电影免费在线| 高潮久久久久久久久久久不卡| 激情在线观看视频在线高清| 久久国产乱子伦精品免费另类| 亚洲av美国av| 99riav亚洲国产免费| 少妇的丰满在线观看| 可以在线观看毛片的网站| 婷婷精品国产亚洲av| 国产av在哪里看| 97超视频在线观看视频| av视频在线观看入口| 成人性生交大片免费视频hd| 亚洲天堂国产精品一区在线| 免费看光身美女| 嫩草影视91久久| 国产精品一及| 97超视频在线观看视频| 十八禁人妻一区二区| 欧美极品一区二区三区四区| 亚洲中文日韩欧美视频| 小说图片视频综合网站| av中文乱码字幕在线| 日韩欧美精品v在线| 十八禁网站免费在线| 搡老妇女老女人老熟妇| 久久精品国产99精品国产亚洲性色| 精品99又大又爽又粗少妇毛片 | 人人妻人人澡欧美一区二区| 麻豆国产97在线/欧美| 中国美女看黄片| 久久精品国产99精品国产亚洲性色| 真人做人爱边吃奶动态| 午夜视频精品福利| 在线免费观看的www视频| 国产伦人伦偷精品视频| 亚洲欧美激情综合另类| 亚洲av片天天在线观看| 久久欧美精品欧美久久欧美| 1024香蕉在线观看| 欧美成狂野欧美在线观看| 黄色丝袜av网址大全| 一级毛片女人18水好多| 亚洲一区二区三区色噜噜| 国产欧美日韩一区二区三| 少妇裸体淫交视频免费看高清| 18禁黄网站禁片午夜丰满| 日韩欧美国产在线观看| 国产精品野战在线观看| av天堂在线播放| 久久精品影院6| 亚洲成av人片免费观看| 少妇的逼水好多| 又粗又爽又猛毛片免费看| 欧美黑人欧美精品刺激| 国产亚洲av嫩草精品影院| 亚洲国产中文字幕在线视频| 亚洲午夜精品一区,二区,三区| av中文乱码字幕在线| 久久精品综合一区二区三区| 国产成人aa在线观看| 久久久久久久久免费视频了| 九九在线视频观看精品| av欧美777| 亚洲欧美一区二区三区黑人| 色综合欧美亚洲国产小说| 香蕉久久夜色| 久久久久久九九精品二区国产| 亚洲,欧美精品.| 中亚洲国语对白在线视频| 久久精品国产99精品国产亚洲性色| 亚洲国产欧美网| 九九在线视频观看精品| 亚洲av成人av| 美女cb高潮喷水在线观看 | 国产一区在线观看成人免费| 舔av片在线| 国产精品美女特级片免费视频播放器 | 美女被艹到高潮喷水动态| 国产亚洲精品久久久久久毛片| 亚洲美女视频黄频| 精品久久久久久久末码| 日韩欧美国产在线观看| 日韩中文字幕欧美一区二区| 深夜精品福利| 后天国语完整版免费观看| 欧美中文日本在线观看视频| 99久久99久久久精品蜜桃| 两个人的视频大全免费| 床上黄色一级片| 99久久无色码亚洲精品果冻| svipshipincom国产片| 国产毛片a区久久久久| 91av网一区二区| 免费高清视频大片| www.www免费av| 精品久久久久久成人av| 亚洲一区二区三区色噜噜| 久久久久久大精品| 99久久综合精品五月天人人| 久久香蕉精品热| 亚洲国产欧洲综合997久久,| 亚洲成a人片在线一区二区| 日韩国内少妇激情av| 久久久成人免费电影| 久久久色成人| 久久精品亚洲精品国产色婷小说| 2021天堂中文幕一二区在线观| 免费av毛片视频| cao死你这个sao货| av黄色大香蕉| 动漫黄色视频在线观看| 哪里可以看免费的av片| 成年人黄色毛片网站| xxx96com| 免费在线观看影片大全网站| 十八禁网站免费在线| 男女之事视频高清在线观看| 人妻久久中文字幕网| 一级毛片精品| 一区二区三区高清视频在线| 欧美日韩中文字幕国产精品一区二区三区| 国产精品亚洲av一区麻豆| 亚洲欧美日韩高清在线视频| 老熟妇仑乱视频hdxx| 国产黄a三级三级三级人| 麻豆国产av国片精品| 午夜精品一区二区三区免费看| 成人特级黄色片久久久久久久| 欧美午夜高清在线| 国产淫片久久久久久久久 | 看黄色毛片网站| 免费在线观看影片大全网站| 精品久久久久久久毛片微露脸| 亚洲人成伊人成综合网2020| 国产伦在线观看视频一区| 最好的美女福利视频网| 狠狠狠狠99中文字幕| 国产真实乱freesex| 国产av麻豆久久久久久久| 久久久久久九九精品二区国产| 床上黄色一级片| 国产美女午夜福利| 黑人操中国人逼视频| 午夜福利在线在线| 久久中文字幕一级| 欧美3d第一页| 级片在线观看| 1000部很黄的大片| 亚洲中文av在线| 在线观看日韩欧美| 一本综合久久免费| 国产精品影院久久| 国产黄色小视频在线观看| 美女高潮的动态| 日韩国内少妇激情av| 色噜噜av男人的天堂激情| 免费搜索国产男女视频| 亚洲欧洲精品一区二区精品久久久| 免费无遮挡裸体视频| 国产高清视频在线播放一区| 美女高潮喷水抽搐中文字幕| 黄片大片在线免费观看| 色视频www国产| 国产午夜精品论理片| 一级a爱片免费观看的视频| 99国产精品一区二区蜜桃av| 性欧美人与动物交配| 曰老女人黄片| 亚洲美女黄片视频| 久久天躁狠狠躁夜夜2o2o| 亚洲天堂国产精品一区在线| 两个人的视频大全免费| 制服丝袜大香蕉在线| 亚洲第一欧美日韩一区二区三区| 国产亚洲精品一区二区www| 国产午夜福利久久久久久| 久久久水蜜桃国产精品网| 国产真实乱freesex| 校园春色视频在线观看| 欧美日本视频| avwww免费| 久久精品91无色码中文字幕| 午夜精品一区二区三区免费看| 91字幕亚洲| 午夜亚洲福利在线播放| 国产人伦9x9x在线观看| 2021天堂中文幕一二区在线观| 欧美在线一区亚洲| 精品国产乱子伦一区二区三区| 午夜视频精品福利| 国产成人精品无人区| 在线播放国产精品三级| 亚洲国产高清在线一区二区三| 波多野结衣高清作品| 99久久国产精品久久久| 国产毛片a区久久久久| 国产精品,欧美在线| 18禁黄网站禁片午夜丰满| 欧美绝顶高潮抽搐喷水| 男女做爰动态图高潮gif福利片| 一边摸一边抽搐一进一小说| 国产1区2区3区精品| 久久欧美精品欧美久久欧美| 色精品久久人妻99蜜桃| 成人欧美大片| 久久精品aⅴ一区二区三区四区| 夜夜爽天天搞| 一级毛片精品| 国产高清激情床上av| 久久九九热精品免费| 美女被艹到高潮喷水动态| 国产精品久久久av美女十八| 美女cb高潮喷水在线观看 | 亚洲精品国产精品久久久不卡| 国产麻豆成人av免费视频| 国产精品乱码一区二三区的特点| 变态另类丝袜制服| 国产97色在线日韩免费| 亚洲 欧美 日韩 在线 免费| 天天添夜夜摸| 久久伊人香网站| 1000部很黄的大片| 国产黄色小视频在线观看| 一本精品99久久精品77| 国产真人三级小视频在线观看| 亚洲五月天丁香| 国产精品一区二区免费欧美| 国产主播在线观看一区二区| 精品午夜福利视频在线观看一区| 91字幕亚洲| 高清毛片免费观看视频网站| 老司机在亚洲福利影院| 岛国在线免费视频观看| 午夜日韩欧美国产| 国产av不卡久久| 欧美国产日韩亚洲一区| 嫩草影视91久久| 国产亚洲av嫩草精品影院| 婷婷亚洲欧美| 国产黄色小视频在线观看| 看片在线看免费视频| 他把我摸到了高潮在线观看| 91麻豆av在线| 亚洲乱码一区二区免费版| 99精品久久久久人妻精品| 久久国产精品影院| av视频在线观看入口| 久久精品国产综合久久久| 亚洲18禁久久av| 国产精品 欧美亚洲| 亚洲精品一区av在线观看| 99在线视频只有这里精品首页| 黄色成人免费大全| 日本a在线网址| 小蜜桃在线观看免费完整版高清| 女生性感内裤真人,穿戴方法视频| 欧美大码av| 美女免费视频网站| 97超级碰碰碰精品色视频在线观看| 人妻夜夜爽99麻豆av| 母亲3免费完整高清在线观看| 黑人操中国人逼视频| 国产成人福利小说| 淫妇啪啪啪对白视频| 国产免费av片在线观看野外av| 国产亚洲欧美98| 精品电影一区二区在线| 99在线视频只有这里精品首页| 小说图片视频综合网站| 免费搜索国产男女视频| 曰老女人黄片| 国产精品久久久久久人妻精品电影| 国产伦精品一区二区三区四那| 日韩欧美三级三区| 一本精品99久久精品77| 1024香蕉在线观看| 欧美大码av| av欧美777| 又爽又黄无遮挡网站| 亚洲av成人不卡在线观看播放网| 别揉我奶头~嗯~啊~动态视频| 在线观看免费视频日本深夜| 亚洲国产精品成人综合色| 欧美乱码精品一区二区三区| 欧美性猛交黑人性爽| 九色国产91popny在线| 国产精品av视频在线免费观看| 美女高潮的动态| 国产三级中文精品| 国内精品久久久久久久电影| 伊人久久大香线蕉亚洲五| 好男人在线观看高清免费视频| 变态另类成人亚洲欧美熟女| 亚洲aⅴ乱码一区二区在线播放| 熟妇人妻久久中文字幕3abv| 99国产综合亚洲精品| 99精品在免费线老司机午夜| 亚洲精品国产精品久久久不卡| 淫妇啪啪啪对白视频| 久久精品国产清高在天天线| 久久久久精品国产欧美久久久| 国产一区在线观看成人免费| 校园春色视频在线观看| 日本 av在线| 国产亚洲精品综合一区在线观看| 嫩草影院精品99| 窝窝影院91人妻| 日韩欧美三级三区| 久久午夜综合久久蜜桃| 午夜免费观看网址| 国产aⅴ精品一区二区三区波| 九九久久精品国产亚洲av麻豆 | 我的老师免费观看完整版| 这个男人来自地球电影免费观看| 黄色日韩在线| 一个人观看的视频www高清免费观看 | 天天躁狠狠躁夜夜躁狠狠躁| 最新在线观看一区二区三区| 无遮挡黄片免费观看| 国产视频内射| 成人三级黄色视频| 成年女人毛片免费观看观看9| 99国产极品粉嫩在线观看| 精品熟女少妇八av免费久了| www.自偷自拍.com| 非洲黑人性xxxx精品又粗又长| 男人舔女人的私密视频| 国产成人av教育| 12—13女人毛片做爰片一| 久9热在线精品视频| av在线蜜桃| 欧美成狂野欧美在线观看| 亚洲专区国产一区二区| 男人的好看免费观看在线视频| 久久香蕉精品热| 老鸭窝网址在线观看| 久久久久国产精品人妻aⅴ院| 少妇裸体淫交视频免费看高清| 香蕉久久夜色| 日本a在线网址| 少妇熟女aⅴ在线视频| 午夜亚洲福利在线播放| 成人国产综合亚洲| 18美女黄网站色大片免费观看| 网址你懂的国产日韩在线| 嫩草影院入口| 又紧又爽又黄一区二区| 禁无遮挡网站| 三级国产精品欧美在线观看 | 午夜影院日韩av| 精品一区二区三区av网在线观看| 国产精品免费一区二区三区在线| 亚洲天堂国产精品一区在线| 欧美黄色片欧美黄色片| 国内精品久久久久精免费| 欧美黑人欧美精品刺激| 精品国内亚洲2022精品成人| 久久精品综合一区二区三区| 香蕉久久夜色| 久久久久久久精品吃奶| 黄色成人免费大全| 亚洲成av人片免费观看| 91字幕亚洲| 在线免费观看不下载黄p国产 | 99热这里只有精品一区 | 国产单亲对白刺激| 中文字幕人成人乱码亚洲影| 亚洲国产中文字幕在线视频| 18禁国产床啪视频网站| 国产探花在线观看一区二区| 国产一区二区三区在线臀色熟女| 一个人看视频在线观看www免费 | 成人亚洲精品av一区二区| 久久精品夜夜夜夜夜久久蜜豆| 99久久综合精品五月天人人| 久久久成人免费电影| 制服人妻中文乱码| 国产午夜精品久久久久久| 看片在线看免费视频| 国产精品自产拍在线观看55亚洲| 超碰成人久久| 亚洲黑人精品在线| 国产视频一区二区在线看| 国产亚洲精品久久久com| 麻豆久久精品国产亚洲av| 好男人在线观看高清免费视频| ponron亚洲| 久久久久性生活片| 国产不卡一卡二| 丰满人妻熟妇乱又伦精品不卡| 精品乱码久久久久久99久播| 中文字幕久久专区| 90打野战视频偷拍视频| 在线十欧美十亚洲十日本专区| 夜夜爽天天搞| 日韩中文字幕欧美一区二区| 久久久国产成人免费| 久久精品人妻少妇| 久久久久国产一级毛片高清牌| 国内揄拍国产精品人妻在线| 精品久久久久久久久久免费视频| 亚洲精品国产精品久久久不卡| 黑人操中国人逼视频| 18禁美女被吸乳视频| 国产精品99久久99久久久不卡| 嫁个100分男人电影在线观看| 午夜福利在线观看免费完整高清在 | 亚洲,欧美精品.| 99热精品在线国产| 天天添夜夜摸| 欧美日韩精品网址| 禁无遮挡网站| 久久久久亚洲av毛片大全| 亚洲成a人片在线一区二区| 国产真人三级小视频在线观看| 99久久成人亚洲精品观看| 亚洲精品色激情综合| 日日夜夜操网爽| 亚洲狠狠婷婷综合久久图片| 亚洲午夜精品一区,二区,三区| 午夜免费激情av| 两个人的视频大全免费| 亚洲国产中文字幕在线视频| 久久精品国产清高在天天线| 精品国内亚洲2022精品成人| 国产精品av久久久久免费| 国产精品亚洲美女久久久| 日日干狠狠操夜夜爽| 国产乱人伦免费视频| 成年人黄色毛片网站| 久久欧美精品欧美久久欧美| 精品99又大又爽又粗少妇毛片 | 欧美大码av| 国产一区二区在线av高清观看| 天堂网av新在线| 国产黄a三级三级三级人| 国产午夜精品论理片| 男女视频在线观看网站免费| 国产99白浆流出| 国产麻豆成人av免费视频| 亚洲美女黄片视频| 国产人伦9x9x在线观看| 视频区欧美日本亚洲| 日本熟妇午夜| a在线观看视频网站| 日韩人妻高清精品专区| 免费看日本二区| 亚洲激情在线av| 真人做人爱边吃奶动态| 岛国在线免费视频观看| 国产一区二区三区视频了| 久久久久性生活片| 99久久精品热视频| 国产探花在线观看一区二区| 男女之事视频高清在线观看| 日韩中文字幕欧美一区二区| 日本撒尿小便嘘嘘汇集6| 国产一区二区在线观看日韩 | 欧美日本视频| 久久天躁狠狠躁夜夜2o2o| 国产精品综合久久久久久久免费| 欧美一级毛片孕妇| 国产精品免费一区二区三区在线| 亚洲午夜理论影院| 午夜福利在线观看吧| 国产爱豆传媒在线观看| 免费看日本二区| 丰满人妻一区二区三区视频av | 欧美精品啪啪一区二区三区| 两性夫妻黄色片| 日本与韩国留学比较| 日韩欧美在线二视频| 九色成人免费人妻av| 不卡av一区二区三区| 99riav亚洲国产免费| 波多野结衣高清无吗| 亚洲国产中文字幕在线视频| 久久香蕉国产精品| 老熟妇乱子伦视频在线观看| 亚洲人成电影免费在线| 男人舔女人下体高潮全视频| 亚洲 欧美一区二区三区| 亚洲av第一区精品v没综合| 熟女电影av网| 精品一区二区三区四区五区乱码| 午夜a级毛片| 啦啦啦韩国在线观看视频| 国产黄色小视频在线观看| 日本黄色视频三级网站网址| xxxwww97欧美| 国产精品久久久人人做人人爽| 精品久久久久久久人妻蜜臀av| 欧美zozozo另类| 亚洲成人久久性| 精品日产1卡2卡| 国产欧美日韩精品亚洲av| 免费看光身美女| 一本一本综合久久| 天天躁狠狠躁夜夜躁狠狠躁| 精品一区二区三区av网在线观看| 午夜亚洲福利在线播放| 不卡一级毛片| 婷婷丁香在线五月| 国产黄a三级三级三级人| 国产精品国产高清国产av| 99精品久久久久人妻精品| 亚洲国产看品久久| 国产伦精品一区二区三区四那| 亚洲aⅴ乱码一区二区在线播放| 一区二区三区高清视频在线| 亚洲男人的天堂狠狠| 哪里可以看免费的av片| 曰老女人黄片| 国产成人av教育| 久久精品国产亚洲av香蕉五月| 亚洲中文日韩欧美视频| 免费看十八禁软件| 日本与韩国留学比较| 国产精品一区二区免费欧美| 18禁美女被吸乳视频| 黄色 视频免费看| 成人亚洲精品av一区二区| 麻豆国产97在线/欧美| 国产黄片美女视频| 免费在线观看成人毛片| 宅男免费午夜| 一个人看视频在线观看www免费 | 特大巨黑吊av在线直播| av欧美777| 日日摸夜夜添夜夜添小说| 天天躁日日操中文字幕| 国产午夜精品论理片| 亚洲熟妇熟女久久| h日本视频在线播放| 久久这里只有精品19| 91麻豆精品激情在线观看国产| 亚洲一区二区三区不卡视频| 久久九九热精品免费| 啦啦啦免费观看视频1| 国产欧美日韩精品一区二区| 亚洲aⅴ乱码一区二区在线播放| 18禁观看日本| 日本三级黄在线观看| 一个人免费在线观看的高清视频| 熟女电影av网| 精品久久蜜臀av无| 免费高清视频大片| h日本视频在线播放| 国产欧美日韩一区二区精品| 国产又色又爽无遮挡免费看| 麻豆一二三区av精品| 亚洲五月天丁香| 人人妻人人澡欧美一区二区| 欧美一级a爱片免费观看看| 欧美成人性av电影在线观看| 91字幕亚洲| 欧美大码av| а√天堂www在线а√下载| 国产爱豆传媒在线观看| av黄色大香蕉| 男女之事视频高清在线观看| 久久久久久九九精品二区国产| www.熟女人妻精品国产| 91av网站免费观看| 三级国产精品欧美在线观看 | 免费高清视频大片| 国产黄片美女视频| 日本黄色片子视频| 亚洲熟妇熟女久久| 日本成人三级电影网站| 桃色一区二区三区在线观看| 长腿黑丝高跟| av福利片在线观看| 成年免费大片在线观看| www.999成人在线观看| 国产精品99久久99久久久不卡| 两人在一起打扑克的视频| 亚洲精品美女久久av网站| h日本视频在线播放| 亚洲一区高清亚洲精品| 国产一区二区在线av高清观看| 国产亚洲av高清不卡| 精品午夜福利视频在线观看一区| 久久久久久大精品|