• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Analysis of the cylinder block tilting inertia moment and its effect on the performance of high-speed electro-hydrostatic actuator pumps of aircraft

    2018-02-02 08:10:24JunhuiZHANGQunCHAOBingXU
    CHINESE JOURNAL OF AERONAUTICS 2018年1期

    Junhui ZHANG,Qun CHAO,Bing XU

    State Key Laboratory of Fluid Power and Mechatronic Systems,Zhejiang University,Hangzhou 310027,China

    1.Introduction

    The future development of general aircraft systems is directed towards more electric aircraft(MEA),in which traditional central hydraulic systems are replaced with local electrically powered actuation systems.1Successful application of the power-by-wire(PBW)technology to MEA makes EHAs easily realizable.Local electrically powered actuation systems have some potential advantages,such as weight reduction,power saving,and improved maintainability,over conventional central hydraulic systems.2–5As shown in Fig.1,a typical EHA system mainly consists of a variable-speed servo motor,afixed displacement and bi-directional axial piston pump,a symmetrical linear actuator,an accumulator,and some related valves,etc.In an EHA system,the symmetrical linear actuator of the primaryflight control surface is motivated using hydraulicfluid,the velocity and direction of which are controlled by thefluid flow from a servo motor driven hydraulic pump called EHA pump.The accumulator is mainly to maintain the pressure in the system,to cool the hydraulicfluid,and to compensate anyfluid loss over the lifetime of the actuator.

    Fig.2 shows the general configuration of an axial piston pump,a type of EHA pump.The cylinder block is held tightly against the valve plate by means of a compressed cylinder block spring,while the valve plate is held in afixed position.There are several piston/slipper assemblies nested within the cylinder block at equal intervals about the centerline of the cylinder block.The slippers remain in a reasonable proximity with the swash plate utilizing a spherical cup and a holddown device called retainer.The shaft is coupled with the cylinder block using a spline mechanism and is supported by two bearings at both shaft ends.When the shaft is driven by a servo motor,the cylinder block rotates about the axis of the shaft and thus all the piston/slipper assemblies reciprocate within the cylinder bores because of the hold-down mechanism and the inclined swash plate.During rotation,thin oilfilms form between the cylinder block and the valve plate,between the pistons and the cylinder block,and between the slippers and the swash plate.These thin oilfilms serve as combined hydrostatic and hydrodynamic bearings respectively.However,a leakageflow occurs across the sliding interfaces due to the existence of these thin oilfilms.Unreasonable gaps between the sliding parts tend to increase the leakageflow as well as the potential for undesirable wear.

    Fig.1 Schematic of an electro-hydraulic actuation system.

    Fig.2 General configuration of an axial piston pump.

    An EHA pump usually operates at a high speed of more than 10,000 r/min since a higher speed means a smaller displacement for a given volumetricflow of the actuator.Therefore,morecompactEHA pumpscanberealizedby increasing the pump speed,which is of importance for improving the power density of the EHA system.Messier-Bugatti and Parker claimed that they have produced very high-speed EHA pumps whose rotational speeds can even reach more than 15,000 r/min.For the aim of higher power density,the continuing development of EHA systems makes a further demand upon EHA pumps for greater rotational speeds.However,high-speed operating conditions will bring several practical problems imposed on EHA pumps.

    Thefirst problem regards pressure pulsation.6,7The pressure within the cylinder block of an axial piston pump easily exhibits undershooting or overshooting when the pump is operating at a high speed.It is found that the undershooting orovershooting pressureincreasesalmostlinearly with increased rotational speed.

    The second problem associated with a high speed is the cavitation.8–11An axial piston pump with a high speed is likely to be in accompany with obvious cavitation.On one hand,the pump speed should be limited below the critical speed that exactly causes cavitation.On the other hand,a higher suction tank pressure is needed for which a booster pump may be used.

    The third problem of a high speed may be concerned with power losses.12–17Power losses arising from high speeds mainly involve friction losses due to metal-to-metal contact,and viscous friction and churning losses due to rotating elements interacting with thefluid filled in the pump case.Some special surface treatments of metals such as duplex TiN coatings14and novel structures such as Power BoostTM18have proven to beeffectivein reducing powerlossesthrough experimental studies.

    The last problem caused by a high speed is the tilt of rotating parts in an axial piston pump.In the past decades,some theoretical and experimental research has been devoted to the slipper tilt.19–25It was found that the slipper tends to tilt away from the swash plate when a pump reaches a high speed.Although some academic attentions have been given to the cylinder block tilt,most studies were occupied with the traditional cylinder block tilt resulting from the pressure difference between the discharge and intake sides.26–30In reality,another type of cylinder block tilt due to the cylinder block tilting inertia moment produced by the inertia forces of piston/slipper assemblies cannot be ignored when a pump operates at a high speed.Ivantysynova et al.29,31,32included the inertia forces of piston/slipper assemblies in elastohydrodynamic(EHD)and thermoelastohydrodynamic(TEHD)models,but all these models were not applied to high-speed conditions and no detailed results about the influence of the cylinder block tilting inertia moment on the pump performance were presented.Manring10,33pointed out the inherent phenomenon of cylinder block tilt and derived the cylinder block tilting criteria;however,the expression for the cylinder block tilting inertia moment was not given explicitly in his study.

    The goal of this study was to investigate the cylinder block tilt in a high-speed EHA pump from the point of view of dynamics.In the present work,an expression for the cylinder block tilting inertia moment was developed that included the translational inertia and centrifugal forces of a piston/slipper assembly.Moreover,high-speed tests on an EHA pump prototype were carried out to examine the effect of the cylinder block tilting inertia moment on the EHA pump performance.

    2.Mathematical model

    In order to better understand the reason for producing the cylinder block tilting inertia moment,the relevant forces acting on a single piston/slipper assembly,as shown in Fig.3,must be accurately defined.Point c in Fig.3 represents the centroid of the piston/slipper assembly.It should be emphasized that just the cylinder block tilting inertia moment will be discussed in this paper,so the relevant forces resulting in the tilting inertia moment only involve the translational inertia force Faand the centrifugal force Frof the piston/slipper assembly.

    In this case,theXYZsystem isfixed in an inertial frame and thexyzsystem attached to the cylinder block rotates relative to theXYZsystem.Suppose that ρ and L are the position vectors of the centroid of the piston/slipper assembly and the center of the piston-slipper ball joint,respectively,relative to the origin in theXYZsystem.Then the absolute acceleration of the centroid of the piston/slipper assembly can be expressed in a vector form as34

    where ω is the absolute angular speed of the cylinder block whose magnitude ω is assumed to be constant,subscriptnrepresents thenth piston/slipper assembly,and subscript r denotes that the scalar quantity or the vector quantity is described relative to thexyzsystem.

    Before evaluating each term of Eq.(1),we note that35

    in which i,j,and k are the unit vectors in theX-direction,Y-direction,andZ-direction,respectively,Ris the pitch circle radius of piston bores,β is the swash plate angle,zcis the initial position of the centroid of thefirst piston/slipper assembly,and φnis the angular position of thenth piston.

    If φ1=0 when the bottom dead center(BDC)is chosen as the position for the derivation of kinematic parameters,then

    where α is the angular interval between two contiguous pistons about thez-axis.

    From Eqs.(1)to(5),we obtain thefinal absolute acceleration of the centroid of thenth piston/slipper assembly as

    in which thefirst term on the right side represents the centrifugal acceleration caused by the rotating motion along with the cylinder block about the negativeZ-direction,and the second term represents the translational acceleration due to the reciprocating motion relative to the cylinder block.

    According to d’Alembert’s principle,the centrifugal acceleration will generate a radial centrifugal force Fr,and the translational acceleration will generate an axial inertia force Fa.If we treat the piston and slipper as a whole analytical object,then we may assume for convenience that the centrifugal force is transferred to the cylinder block and the axial inertia force is transferred to the swash plate.The reaction force FNfrom the swash plate results in a remaining lateral force FNythat produces the effect of cylinder block tilt,along with the centrifugal force Fr.Thus,taking moment about the origin,we obtain the cylinder block tilting inertia moment as follows:

    Fig.3 Forces acting on a single piston/slipper assembly.

    wheremis the individual piston/slipper assembly mass,Nis the total number of pistons,and Lnis the moment arm of thenth lateral force,which can be obtained by

    wherez0is the distance from the shaft reaction to theXYplane as shown in Fig.3.Substituting Eqs.(4)and(8)into Eq.(7),the cylinder block tilting inertia moment is given by

    Considering that all pistons are nested in a circular array within the cylinder block at equal angular intervals about theZ-axis,then the following simplifications can be obtained due to mathematical symmetry:

    Finally,the cylinder block tilting inertia moment due to the centrifugal and translational accelerations presented in Eq.(9)can be reduced to a simplified form as follows:

    3.Analysis and discussion

    It can be seen from Eq.(15)that the centrifugal and axial inertia forces of the piston/slipper assembly only produce a tilting inertia moment in the negativeX-direction,which results in the cylinder block tilting towards the bottom dead center(BDC),as shown in Fig.4 where the gap between the cylinder block and the valve plate has been magnified for illustration purpose.In reality,the oilfilm thickness between the cylinder block and the valve plate is usually on the order of magnitude of microns between 0 and 100 μm based upon measured and simulated results.26–29

    It has to be pointed out that the tilting inertia moment MTis exactly perpendicular to the moment acting on the cylinder block by the pressure distribution along the discharge and intake sides,Mmean.This hydraulic moment is the traditional moment that determines the cylinder block balance about theY-axis.Therefore,this tilting inertia moment MTcannot be counteracted byMmeandirectly,and a potential metal-tometal contact and an increased leakageflow are likely to occur across the cylinder block/valve plate interface.

    Although direct measurement of the oilfilm thickness between the cylinder block and the valve plate at a high pump speed was not carried out in this paper,previous experimental investigations into the cylinder block/valve plate pair have been performed at low pump speeds.26–28,36In the literature36,three micro position transducers GS1,GS2,and GS3 were mounted between the cylinder block and the valve plate at certain angular intervals,as shown in Fig.5.Transducers GS1 and GS2 are located in the vicinity of the top dead center(TDC),and transducer GS3 is close to the BDC.

    Fig.6 gives the actual oilfilm thicknesses respectively through three displacement transducers.It is found that the oilfilm thickness between the cylinder block and the valve plate is significantly dependent on the pump speed.The oilfilm thicknesses measured through GS1 and GS2 increase with an increased pump speed,while the oilfilm thickness measured through GS3 decreases with an increased pump speed.This may be explained by the fact that the tilting effect of the cylinder block due to the tilting inertia moment(see Eq.(15))strengthens with an increased pump speed,resulting in the cylinder block tilting towards the BDC.

    The tilting effect of the cylinder block may not trigger catastrophic machine failures at a low pump speed.On one hand,the occurrences of a hydrodynamic effect and a thermal wedge effect between the cylinder block and the valve plate will prevent the cylinder block from serious tilt.On the other hand,a low pump speed means a small tilting inertia moment acting on the cylinder block and thus will not bring a significant difference for the cylinder block balance.However,this tilting effect can no longer be neglected once the EHA pump reaches a high speed(e.g.,more than 10000 r/min).Fig.7 shows the dependence of the tilting inertia moment on the pump speed for different discharge pressures of 2,5,10,and 20 MPa.

    Fig.4 Cylinder block tilting towards the BDC.

    Fig.5 Transducer positions located between the cylinder block and the valve plate for oilfilm thickness measurement.

    It has to be noted that the tilting inertia moment value has been normalized by the above mentioned hydraulic momentMmeanas follows:37

    Fig.6 Actual oilfilm thickness between the cylinder block and the valve plate for a discharge pressure of 1.6 MPa.36

    Fig.7 Normalized tilting inertia moment of the cylinder block.

    wherepis the discharge pressure,R1andR2are the inside and outside radii of the inner sealing land on the cylinder block,respectively,R3andR4are the inside and outside radii of the outer sealing land on the cylinder block,respectively,and α1is the angular span of the cylinder block kidney,as depicted in Fig.8.

    Fig.7 indicates that the tilting inertia moment increases dramatically with the pump speed since it is proportional to the square of the pump speed as presented in Eq.(15).The tilting effect of the cylinder block due to the centrifugal and axial inertia forces of the piston/slipper assembly may be negligible at low speeds in engineering practice.However,it cannot be ignored especially when the EHA pump operates at a high speed and a low discharge pressure.For example,the tilting inertia moment can be about 1.5 times of the hydraulic moment produced by the pressure distribution between the cylinder block and the valve plate when the EHA pump speed reaches 20000 r/min.This considerable additional tilting inertia moment may lead to metal-to-matal contact and wedgeshaped oilfilm across the cylinder block/valve plate interface.

    Fig.8 A schematic configuration of the cylinder block bottom face.

    4.Experiments

    In order to estimate the EHA pump performance at a high rotational speed,a high-speed test rig that could provide a drive speed up to16000 r/min was set up,as shown in Fig.9.

    It is important to underline that the performance tests were conducted at variable rotational speeds from 1000 r/min to 9000 r/min for constant pressures of 2,5,10,and 20 MPa,respectively.The swash plate was held in afixed position at a certain inclined angle with respect to the cylinder block during the tests.The EHA pump prototype had a theoretical volumetric displacement of 3 mL/r.The inlet oil temperature was maintained at(20± 1)°C with the aim to eliminate the impact of the inlet oil temperature on the pump performance as much as possible.

    As mentioned previously,a high rotational speed tends to trigger the cylinder block tilting away from the valve plate,resulting in subsequent increased leakage and potential wear between the cylinder block and the valve plate.It seems that the leakageflow from the cylinder block/valve plate should be measured directly to investigate the effect of the cylinder block tilting inertia moment on the EHA pump prototype performance.However,it was extremely difficult for us to measure the leakageflow from the cylinder block/valve plate interface separately from other leakage sources such as the piston/cylinder block interface and the slipper/swash plate interface.Therefore we measured the pump case drain leakageflow instead of the leakageflow from the cylinder block/valve plate interface.Inaddition,wepaidourattentiontothewearpatternofthesliding surface between the cylinder block and the valve plate attempting to predict the occurrence of cylinder block tilting.

    The trend of the pump case drain leakageflowQLof the investigated EHA pump prototype at different pump speeds for discharge pressures of 2,5,10,and 20 MPa is shown in Fig.10(a).Fig.10(a)highlights that the pump case drain leakageflow increases with an increased pump speed,which is consistent with the tendency of the cylinder block tilting inertia moment shown in Fig.7.Furthermore,it can be seen from Fig.10 that the pump case drain leakageflow at a speed higher than 5000 r/min increases more sharply than that lower than 5000 r/min,which may be partly explained by the fact that the tilting effect of the cylinder block is quite significant when the EHA pump operates at a high rotational speed.It can be observed from Eq.(15)that the cylinder block tilting inertia moment is a function of the pump speed.However,the pump case drain leakageflow is the comprehensive results of the pump pressure and speed.In order to estimate the dependence of the tilting effect of the cylinder block on the pump speed,the relative pump case drain leakageflow is compared between these four different discharge pressures.The relative pump case drain leakage is defined as the ratio of the leakage flow at a certain pump speed to that at 1000 r/min,QL1000.Fig.10(b)demonstrates that the pump case drain leakageflow at a low pressure is more dependent on the pump speed than that at a high pressure.

    Considering that only comparing the measured pump case drain leakage flow at a variety of pump speeds is not sufficient enough to reveal the characteristics of the cylinder block tilting behavior,more detailed investigation should be further provided.After accomplishing the general performance tests on the EHA pump prototype,the EHA pump was dismantled for the purpose of insight into the sliding surface between the cylinder block and the valve plate,as shown in Fig.11.It can be observed that the non-sealing land of the cylinder block suffered more severe wear than the sealing land,which implies that the cylinder block was likely to tilt away from the valve plate and consequently a metal-to-metal contact between the cylinder block and the valve plate took place.

    By the way,it can be seen from the right-hand side of Fig.11 that an obvious wear difference of the valve plate sliding surface appears between the intake and discharge sides,which is attributed to the unbalanced hydraulic moment between the discharge and intake sides.However,this kind of wear is not the focus of this paper as there is sufficient literature concerned with it.26–30At this point,much more attention will be given to the specified wear of the valve plate sliding surface in the vicinities of the TDC and the BDC.

    The sliding surface profiles of the cylinder block and the valve plate were detected by a trilinear coordinates measuring instrument and a surface roughness measuring instrument,respectively,asshowninFig.12.Inordertocomparethesliding surfaceprofilesofthecylinderblockbeforeandafterhigh-speed tests,the relative heights(relative to a certain non-sliding plane)of nine points located on the cylinder block sliding surface were measured,asshowninFig.13.Theseninemeasuredpointswere dividedintothree groups(i.e.,A,B,andC),andeachgrouphad threepoints.(i.e.,Ai,Bi,andCi,i=1,2,3).Thesepointsofeach group were arranged in the same radial direction since the wear difference of the sliding surface along the radial direction could reflect the wear pattern of the sliding surface.

    Fig.14 shows the measured heights of all the points shown in Fig.13 before and after high-speed tests.It remains to be noted that the horizontal coordinate represents the ID numbers of the points that are located in the same radial direction,and the vertical coordinate represents the relative height of the cylinder block sliding surface before and after tests.A smaller relative height means an occurrence of more serious wear at the corresponding location.

    Fig.9 Test rig for performance tests on the high-speed EHA pump prototype.

    Fig.10 Pump case drain leakageflow vs pump speed for different discharge pressures of 2 MPa,5 MPa,10 MPa,and 20 MPa.

    Fig.11 Photograph of the sliding surface between the cylinder block and the valve plate after being dismantled.

    Fig.12 Sliding surface profile measurements of the cylinder block and the valve plate.

    Fig.13 Measured points located on the cylinder block sliding surface.

    It can be concluded that wear of the cylinder block sliding surface took place during the pump operation by comparing Fig.14(a)and(b).In addition,the various relative height reductions from point 1 to point 3 in each group in Fig.14(b)indicate that more serious wear occured near the outside region of the cylinder block sliding surface than near the inside region.In other words,the sliding surface of the cylinder block that was subject to both the tilting inertia moment and the unbalanced hydraulic moment changed from a flat configuration to a convex configuration during rotation.

    This finding confirms the existence of a cylinder block tilt when the cylinder block rotates on the sliding surface of the stationary valve plate.However,the cylinder block tilt cannot be simply attributed to the tilting inertia moment described in this paper without further investigation.As previously mentioned,the unbalanced hydraulic moment between the discharge and intake sides can also result in a cylinder block tilt and consequently lead to wear of the sliding surface between the cylinder block and the valve plate.Therefore,the sliding surface profile of the stationary valve plate needs to be measured,in combination with the measurement of the cylinder block sliding surface profile.

    As shown in Fig.12,the probe of the surface roughness measuring instrument moved along the TDC/BDC axis that was in the same direction as the arrow.The real sliding surface profiles at the TDC and BDC vicinities are demonstrated in Fig.15 from which it can be observed that the surface roughness value in the vicinity of the BDC is smaller than that in the vicinity of the TDC.This observation agrees with the previous analysis in this research,which predicts that the tilting inertia moment attempts to make the cylinder block tilt towards the BDC,as shown in Fig.4,and thus the sliding surface region close to the BDC has more opportunity to get a metal-tometal contact than that close to the TDC.Furthermore,the above observation partly explains the fact that the pump case drain leakageflow increases dramatically with the pump speed because a wedge-shaped oilfilm forms across the cylinder block/valve plate interface due to the cylinder block tilt.

    Additionally,comparing the wear condition between the cylinder block and the valve plate,wefind that the cylinder block suffered more serious wear than the valve plate.This is because the material of the cylinder block is soft brass while that of the valve plate is nitrided steel.

    Fig.14 Relative heights of measured points before and after high-speed tests.

    Fig.15 Surface roughness measurements in the TDC and BDC vicinities.

    5.Conclusions

    The tilting inertia moment exerted on the cylinder block by piston/slipper assemblies has been derived in this paper in order to examine the effect of the tilting inertia moment on the cylinder block tilt.Based on analytical and experimental results,the following conclusions may be drawn:

    1.The tilting inertia moment acting on the cylinder block by the inertia forces of a piston/slipper assembly can be attributed to the centrifugal and translational accelerations of the piston/slipper assembly.

    2.The tilting inertia moment produced by a piston/slipper assembly has a significant effect on the cylinder block tilt.This tilting effect attempts to make the cylinder block tilt towards the BDC,which can give rise to the occurrence of metal-to-metal contact between the cylinder block and the valve plate in the vicinity of the BDC.

    3.The cylinder block tilt due to the tilting inertia moment also causes an obvious increase in the pump case drain leakageflow because the cylinder block tilting behavior contributes to a wedge-shaped oilfilm across the cylinder block/valve plate interface.

    4.The cylinder block tilt within an EHA pump is an inherent phenomenon which cannot be ignored especially at high speeds.In an EHA pump design,the tilting inertia moment should be taken into account when performing the force balance analysis of the cylinder block.

    5.The tilting inertia moment acting on the cylinder block could be reduced to some extent by introducing some novel structures or parameter optimization for an EHA pump design.For example,according to Eq.(15),light pistons could be adopted instead of common ones to decrease the tilting inertia moment.

    Acknowledgements

    The authors would like to thank the National Basic Research Program of China(No.2014CB046403)and the National Natural Science Foundation of China(No.U1509204)for theirfinancial supports.

    1.Andersson J,Krus P,Nilsson K.Optimization as a support for selection and design of aircraft actuation systems.Optimization1998;98:39843.

    2.Crowder R,Maxwell C.Simulation of a prototype electrically powered integrated actuator for civil aircraft.Proc Inst Mech Eng G-J Aerosp Eng1997;211(6):381–94.

    3.Navarro R.Performance of an electro-hydrostatic actuator on the F-18 systems research aircraft.Washington,D.C.:NASA;1997.Report No.:NASA/TM-97-206224.

    4.Dominique VDB.The A380flight control electrohydro-static actuators,achievements and lessons learnt.25th International Congress of the Aeronautical Sciences;2006 Sep 3–8;Hamburg,Germany.2006.p.1–8.

    5.Chakraborty I,Mavris DN,Emeneth M,Schneegans A.A methodology for vehicle and mission level comparison of more electric aircraft subsystem solution:application to theflight control actuation system.Proc Inst Mech Eng G-J Aerosp Eng2014;229(6),0954410014544303.

    6.Edge KA,Darling J.The pumping dynamics of swash plate piston pumps.JDynSystMeasControl-TransASME1989;111(2):307–12.

    7.Carsten FB,Lu¨XJ,Stanislav S.Pressure compensator(PC)pressure overshoot analysis and experimental research of an open circuit pump.2015 International Conference on Fluid Power and Mechatronics(FPM);2015 Aug 5-7;Harbin,China.2015.p.910–13.

    8.Harris RM,Edge KA,Tilley DG.The suction dynamics of positive displacement axial piston pumps.J Dyn Syst Meas Control-Trans ASME1994;116(2):281–7.

    9.Yamaguchi A,Takabe T.Cavitation in an axial piston pump.Bull JSME1983;26(211):72–8.

    10.Manring ND,Mehta VS,Nelson BE,Graf KJ,Kuehn JL.Scaling the speed limitations for axial-piston swash-plate type hydrostatic machines.J Dyn Syst Meas Control-Trans ASME2014;136(3):031004.

    11.Kumar S,Bergada JM.The effect of piston grooves performance in an axial piston pumps via CFD analysis.Int J Mech Sci2013;66:168–79.

    12.Olsson H.Power losses in an axial piston pump used in industrial hydrostatic transmissions.Proceedings of the 8th Scandinavian International Conference on Fluid Power;2003 May 7–9;Tampere,Finland.2003.p.491–505.

    13.Hong YS,Doh YH.Analysis on the friction losses of a bent-axis type hydraulic piston pump.KSME Int J2004;18(9):1668–79.

    14.Lee SY,Kim SD,Hong YS.Application of the duplex TiN coatings to improve the tribological properties of electro hydrostatic actuator pump parts.Surf Coat Technol2005;193(1):266–71.

    15.Rahmfeld R,Marsch S,Go¨llner W,Lang T,Dopichay T,Untch J.Efficiency potential of dry case operation for bent-axis motors.Proceedings of the 8th International Fluid Power Conference(IFK);2012 Mar 26–28;Dresden,Germany.2012.p.73–86.

    16.Theissen H,Gels S,Murrenhoff H.Reducing energy losses in hydraulic pumps.Proceedings of the 8th International Conference on Fluid Power Transmission and Control;2013 Apr 9–11;Hangzhou,China.2013.p.77–81.

    17.Xu B,Zhang JH,Li Y,Chao Q.Modeling and analysis of the churning losses characteristics of swash plate axial piston pump.2015 International Conference on Fluid Power and Mechatronics(FPM);2015 Aug 5–7;Harbin,China.2015.p.22–6.

    18.Parker Hannifin.Added power for your saw motor– a simple way to boost performance.2005.Available from:www.parker.com/euro_mcd.

    19.Hooke CJ,Kakoullis YP.The effects of centrifugal load and ball friction on the lubrication of slippers in axial piston pumps.6th International Fluid Power Symposium;1981 Apr 8–10;Cambridge,England.1981.p.179–91.

    20.Hooke CJ,Li KY.The lubrication of slippers in axial piston pumps and motors—the effect of tilting couples.Proc Inst Mech Eng C-J Mec1989;203(5):343–50.

    21.Koc E,Hooke CJ.Considerations in the design of partially hydrostatic slipper bearings.Tribol Int1997;30(11):815–23.

    22.Harris RM,Edge KA,Tilley DG.Predicting the behavior of slipper pads in swashplate-type axial piston pumps.J Dyn Syst Meas Control-Trans ASME1996;118(1):41–7.

    23.Manring ND.Slipper tipping within an axial-piston swash-plate type hydrostatic pump.ASME International Mechanical Engineering Congress and Exposition;1998 Nov 15–20;Anaheim,California,USA.1998.p.169–75.

    24.Manring ND.Predicting the required slipper hold-down force within an axial-piston swash-plate type hydrostatic pump.ASME International Mechanical Engineering Congress and Exposition;2001 Nov 11–16;New York,USA.2001.p.2513–22.

    25.Borghi M,Specchia E,Zardin B,Corradini E.The critical speed of slipper bearings in axial piston swash plate type pumps and motors.2009 ASME Dynamic Systems and Control Conference;2009 Oct 12–14;Hollywood,California,USA.2009.p.267–74.

    26.Kim JK,Jung JY.Measurement offluid film thickness on the valve plate in oil hydraulic axial piston pumps(I)-bearing pad effects.KSME Int J2003;17(2):246–53.

    27.Kim JK,Kim HE,Lee YB,Jung JY,Oh SH.Measurement offluid film thickness on the valve plate in oil hydraulic axial piston pumps(Part II:Spherical design effects).J Mech Sci Technol2005;19(2):655–63.

    28.Deeken M.Simulation of the tribological contacts in an axial piston machine.2004 ASME International Mechanical Engineering Congress and Exposition;2004 Nov 13–20;Anaheim,California,USA.2004.p.71–5.

    29.Wieczorek U,Ivantysynova M.Computer aided optimization of bearing and sealing gaps in hydrostatic machines—the simulation tool CASPAR.Int J Fluid Power2002;3(1):7–20.

    30.Bergada JM,Davies DL,Kumar S,Watton J.The effect of oil pressure and temperature on barrelfilm thickness and barrel dynamics of an axial piston pump.Meccanica2012;47(3):639–54.

    31.Ivantysynova M,Lasaar R.An investigation into micro-and macrogeometric design of piston/cylinder assembly of swash plate machines.Int J Fluid Power2004;5(1):23–36.

    32.Chacon R,Ivantysynova M.An investigation of the impact of micro surface on the cylinderblock/valve plate interface performance.8th FPNI Ph.D Symposium on Fluid Power;2014 June 11–13;Lappeenranta,Finland.2014.p.V001T02A006 –V001T02A006.

    33.Manring ND.Tipping the cylinder block of an axial-piston swashplate type hydrostatic machine.J Dyn Syst Meas Control-Trans ASME2000;122(1):216–21.

    34.Greenwood DT.Principlesofdynamics.Englewood Cliffs(NJ):Prentice-Hall;1988.

    35.Ivantysyn J,Ivantysynova M.Hydrostatic pumps and motors.New Dehli:Akademia Books International;2001.

    36.Zhao YX.The research of valve plate failure for swashplate piston pump.Chinese Hydraul Pneum.2010;5:64–8[Chinese].

    37.Zhai PX.The design of swash-plate axial piston pump.Beijing:Coal Industry Press;1978[Chinese].

    一级片'在线观看视频| 国产午夜精品久久久久久| 久久久国产欧美日韩av| 国产视频一区二区在线看| 久久国产精品影院| 黄色成人免费大全| 在线十欧美十亚洲十日本专区| 亚洲av五月六月丁香网| 亚洲国产精品999在线| 国产亚洲欧美在线一区二区| 久久久久国产一级毛片高清牌| 午夜免费鲁丝| 999精品在线视频| 丰满的人妻完整版| 十八禁人妻一区二区| 欧洲精品卡2卡3卡4卡5卡区| 女同久久另类99精品国产91| 一进一出好大好爽视频| 在线观看午夜福利视频| 制服人妻中文乱码| av天堂在线播放| 中文字幕人妻丝袜一区二区| 久久精品亚洲av国产电影网| 欧美大码av| 久久精品国产亚洲av香蕉五月| 免费观看人在逋| 女警被强在线播放| 91在线观看av| 丁香欧美五月| 久久精品国产亚洲av高清一级| 热99re8久久精品国产| 脱女人内裤的视频| 亚洲中文av在线| 看片在线看免费视频| 又黄又粗又硬又大视频| 搡老岳熟女国产| 满18在线观看网站| 亚洲成国产人片在线观看| 91在线观看av| 亚洲成人免费av在线播放| 久久精品人人爽人人爽视色| 老司机午夜十八禁免费视频| 国产成人精品久久二区二区免费| 又黄又爽又免费观看的视频| 在线播放国产精品三级| 欧美黑人欧美精品刺激| 日本黄色日本黄色录像| 国产av又大| 欧美在线黄色| avwww免费| 一区二区日韩欧美中文字幕| 精品久久久久久,| 天堂动漫精品| 久久欧美精品欧美久久欧美| 午夜精品在线福利| 国产成人精品无人区| 久久久久国内视频| 性少妇av在线| 怎么达到女性高潮| 9热在线视频观看99| 午夜视频精品福利| 日本欧美视频一区| 亚洲av第一区精品v没综合| 久久久久久久久久久久大奶| 欧美丝袜亚洲另类 | 午夜免费观看网址| 淫秽高清视频在线观看| 精品久久久久久久毛片微露脸| 长腿黑丝高跟| 久久久国产精品麻豆| 黄色视频不卡| 制服诱惑二区| 很黄的视频免费| 51午夜福利影视在线观看| 丝袜美腿诱惑在线| 久9热在线精品视频| 99久久综合精品五月天人人| 热re99久久国产66热| 一级毛片精品| 亚洲色图av天堂| 亚洲国产欧美日韩在线播放| 久久人人97超碰香蕉20202| 99久久人妻综合| 久久精品人人爽人人爽视色| 亚洲色图 男人天堂 中文字幕| 国产欧美日韩综合在线一区二区| 最近最新中文字幕大全电影3 | 日本 av在线| 国产欧美日韩精品亚洲av| 国产成人精品在线电影| 母亲3免费完整高清在线观看| 国产精品久久视频播放| 日韩 欧美 亚洲 中文字幕| 欧美午夜高清在线| 午夜a级毛片| 欧美黑人欧美精品刺激| 香蕉丝袜av| 交换朋友夫妻互换小说| 母亲3免费完整高清在线观看| 久久香蕉激情| 一级片'在线观看视频| 国产成人免费无遮挡视频| www日本在线高清视频| www日本在线高清视频| 国产又色又爽无遮挡免费看| 欧美黄色片欧美黄色片| 国内毛片毛片毛片毛片毛片| 久久精品成人免费网站| 亚洲人成77777在线视频| 男女下面插进去视频免费观看| 母亲3免费完整高清在线观看| 美女扒开内裤让男人捅视频| 91老司机精品| 国产精品99久久99久久久不卡| 精品一区二区三卡| 午夜福利,免费看| 久久人妻福利社区极品人妻图片| 两人在一起打扑克的视频| 亚洲,欧美精品.| 成人国产一区最新在线观看| 国产男靠女视频免费网站| 午夜福利在线观看吧| 国产亚洲av高清不卡| 激情视频va一区二区三区| 三上悠亚av全集在线观看| 国产亚洲欧美精品永久| 欧美中文综合在线视频| 精品久久久久久久久久免费视频 | 色播在线永久视频| 女同久久另类99精品国产91| 91成人精品电影| 一进一出好大好爽视频| 最近最新中文字幕大全免费视频| 精品久久蜜臀av无| 黄色毛片三级朝国网站| 国产亚洲精品一区二区www| 99久久国产精品久久久| 日韩欧美在线二视频| 91九色精品人成在线观看| 成人国语在线视频| 亚洲精品国产一区二区精华液| 黄色怎么调成土黄色| 757午夜福利合集在线观看| 亚洲中文字幕日韩| 亚洲成人久久性| 国产三级在线视频| 人人妻人人爽人人添夜夜欢视频| 中文字幕另类日韩欧美亚洲嫩草| 国产色视频综合| 免费高清视频大片| 国产伦人伦偷精品视频| 国产成人精品无人区| 深夜精品福利| 国产成人影院久久av| 国产成人啪精品午夜网站| 欧美性长视频在线观看| 村上凉子中文字幕在线| 欧美日本中文国产一区发布| 国产黄色免费在线视频| 少妇的丰满在线观看| 日韩有码中文字幕| 极品教师在线免费播放| 在线观看免费午夜福利视频| 女警被强在线播放| 夜夜躁狠狠躁天天躁| 日韩免费高清中文字幕av| 午夜精品国产一区二区电影| 91麻豆精品激情在线观看国产 | 久久热在线av| 亚洲午夜精品一区,二区,三区| 精品人妻1区二区| 久久久精品欧美日韩精品| 成人影院久久| 日韩有码中文字幕| 老司机亚洲免费影院| 午夜免费观看网址| av片东京热男人的天堂| 久久久久久免费高清国产稀缺| 午夜福利免费观看在线| xxx96com| 国产xxxxx性猛交| 亚洲五月婷婷丁香| 热99国产精品久久久久久7| 亚洲av美国av| 久久久久国产精品人妻aⅴ院| 一进一出好大好爽视频| 少妇的丰满在线观看| 天堂俺去俺来也www色官网| 亚洲性夜色夜夜综合| 国产成人啪精品午夜网站| 成人av一区二区三区在线看| 90打野战视频偷拍视频| 成人影院久久| 国产一区二区激情短视频| 国产黄色免费在线视频| www.www免费av| 人妻久久中文字幕网| 黄色丝袜av网址大全| 国产亚洲精品久久久久久毛片| 久久人人精品亚洲av| 久久人妻熟女aⅴ| 麻豆av在线久日| 高清在线国产一区| 免费少妇av软件| 欧美在线一区亚洲| 亚洲色图 男人天堂 中文字幕| 国产麻豆69| 别揉我奶头~嗯~啊~动态视频| 高清av免费在线| 国产高清videossex| 精品久久久久久成人av| 久久99一区二区三区| 99香蕉大伊视频| 亚洲成a人片在线一区二区| 日日爽夜夜爽网站| 在线十欧美十亚洲十日本专区| 搡老岳熟女国产| 亚洲 欧美 日韩 在线 免费| 免费少妇av软件| 精品一品国产午夜福利视频| 老汉色av国产亚洲站长工具| 最好的美女福利视频网| 国产视频一区二区在线看| 精品人妻1区二区| 日韩大尺度精品在线看网址 | 日日摸夜夜添夜夜添小说| 色哟哟哟哟哟哟| 久久精品影院6| 中文字幕另类日韩欧美亚洲嫩草| 亚洲一卡2卡3卡4卡5卡精品中文| 国产麻豆69| 好看av亚洲va欧美ⅴa在| 一区二区三区激情视频| 夜夜看夜夜爽夜夜摸 | 又大又爽又粗| 18禁黄网站禁片午夜丰满| 麻豆国产av国片精品| 在线观看免费午夜福利视频| 久久九九热精品免费| 日韩大码丰满熟妇| 国产精品久久视频播放| 久久99一区二区三区| 婷婷丁香在线五月| 在线观看一区二区三区激情| 少妇裸体淫交视频免费看高清 | 一进一出抽搐动态| 91在线观看av| 亚洲欧美一区二区三区久久| 日本免费一区二区三区高清不卡 | 91麻豆精品激情在线观看国产 | 久久人妻av系列| 国产99久久九九免费精品| 亚洲色图综合在线观看| 真人做人爱边吃奶动态| 欧美 亚洲 国产 日韩一| 久久久久久人人人人人| 精品乱码久久久久久99久播| a级毛片在线看网站| 国产精品久久电影中文字幕| 欧美精品亚洲一区二区| 国产91精品成人一区二区三区| 亚洲成av片中文字幕在线观看| 一级,二级,三级黄色视频| 国产成人一区二区三区免费视频网站| 免费观看精品视频网站| 亚洲全国av大片| 巨乳人妻的诱惑在线观看| 国产三级黄色录像| 女人精品久久久久毛片| 高潮久久久久久久久久久不卡| 亚洲成人久久性| 激情在线观看视频在线高清| 亚洲人成网站在线播放欧美日韩| 亚洲五月色婷婷综合| 久久精品国产亚洲av香蕉五月| 久久性视频一级片| 国产亚洲精品综合一区在线观看 | 午夜福利在线免费观看网站| aaaaa片日本免费| 国产三级黄色录像| 天天添夜夜摸| 一区在线观看完整版| 美女福利国产在线| 99久久99久久久精品蜜桃| 亚洲专区国产一区二区| 男女做爰动态图高潮gif福利片 | 欧美一区二区精品小视频在线| 亚洲欧美日韩无卡精品| 操美女的视频在线观看| 亚洲色图综合在线观看| 999久久久精品免费观看国产| 男女床上黄色一级片免费看| 亚洲五月天丁香| 国产深夜福利视频在线观看| 视频区欧美日本亚洲| 人人妻人人澡人人看| 免费观看精品视频网站| 嫩草影视91久久| 亚洲九九香蕉| 亚洲五月婷婷丁香| 国产人伦9x9x在线观看| 村上凉子中文字幕在线| 满18在线观看网站| 亚洲在线自拍视频| 久久久久亚洲av毛片大全| 18禁美女被吸乳视频| 国产av一区在线观看免费| 动漫黄色视频在线观看| 精品久久久久久久毛片微露脸| 校园春色视频在线观看| 啦啦啦免费观看视频1| 欧美激情高清一区二区三区| 日本a在线网址| 国产精华一区二区三区| 啦啦啦在线免费观看视频4| 亚洲人成电影观看| 亚洲欧美日韩高清在线视频| 亚洲国产欧美日韩在线播放| 亚洲激情在线av| 国产亚洲精品久久久久5区| 久久久久久亚洲精品国产蜜桃av| 久久国产精品人妻蜜桃| 中文字幕高清在线视频| 9热在线视频观看99| 在线观看免费视频网站a站| 免费人成视频x8x8入口观看| 成人18禁在线播放| 色哟哟哟哟哟哟| 亚洲av日韩精品久久久久久密| 日日夜夜操网爽| 久久久久久亚洲精品国产蜜桃av| 韩国av一区二区三区四区| 免费少妇av软件| 天堂√8在线中文| 久久这里只有精品19| 欧美乱色亚洲激情| 啦啦啦免费观看视频1| 午夜免费激情av| 热re99久久国产66热| 在线永久观看黄色视频| 日韩三级视频一区二区三区| 香蕉久久夜色| 国产伦一二天堂av在线观看| 香蕉丝袜av| 热re99久久国产66热| 国产三级黄色录像| 国产精品一区二区精品视频观看| 人成视频在线观看免费观看| 国产伦一二天堂av在线观看| 精品免费久久久久久久清纯| 看免费av毛片| 午夜福利欧美成人| 丝袜人妻中文字幕| svipshipincom国产片| 日韩免费高清中文字幕av| 悠悠久久av| 欧美在线黄色| a级毛片在线看网站| 国产一区二区在线av高清观看| 国产欧美日韩一区二区精品| 在线观看舔阴道视频| 女人被躁到高潮嗷嗷叫费观| 女人被躁到高潮嗷嗷叫费观| 天堂中文最新版在线下载| 9色porny在线观看| 国产野战对白在线观看| 日韩高清综合在线| 午夜91福利影院| 国产成年人精品一区二区 | 国产精品国产高清国产av| 五月开心婷婷网| 正在播放国产对白刺激| 亚洲精品一区av在线观看| 日韩高清综合在线| 高清欧美精品videossex| 天堂√8在线中文| 精品国产一区二区三区四区第35| 狠狠狠狠99中文字幕| 亚洲情色 制服丝袜| 亚洲精品中文字幕一二三四区| 欧美大码av| 波多野结衣高清无吗| 中国美女看黄片| 免费一级毛片在线播放高清视频 | 亚洲五月婷婷丁香| 亚洲精品在线美女| 国产一区二区激情短视频| 精品日产1卡2卡| ponron亚洲| 久久久久久久久中文| 国产高清激情床上av| av片东京热男人的天堂| 亚洲精品中文字幕在线视频| 欧美在线一区亚洲| 韩国av一区二区三区四区| 国产欧美日韩精品亚洲av| 美女扒开内裤让男人捅视频| 亚洲少妇的诱惑av| 午夜福利免费观看在线| 人人妻人人澡人人看| 女性被躁到高潮视频| 国产精品久久电影中文字幕| 一本大道久久a久久精品| 亚洲片人在线观看| 成年人黄色毛片网站| 国产成+人综合+亚洲专区| 99热只有精品国产| 色婷婷av一区二区三区视频| 国产精品亚洲一级av第二区| 午夜91福利影院| 一区福利在线观看| 黄频高清免费视频| 黄色丝袜av网址大全| 亚洲国产欧美日韩在线播放| av超薄肉色丝袜交足视频| 又黄又粗又硬又大视频| 欧美午夜高清在线| 精品国产一区二区久久| 一级黄色大片毛片| 久久久久久大精品| 高清av免费在线| 亚洲精品在线观看二区| 免费看十八禁软件| 看片在线看免费视频| 久久精品人人爽人人爽视色| 看片在线看免费视频| 午夜福利欧美成人| 精品福利永久在线观看| 日日干狠狠操夜夜爽| 最近最新中文字幕大全电影3 | 亚洲精品成人av观看孕妇| 欧美午夜高清在线| 成年人黄色毛片网站| 国产精品野战在线观看 | 青草久久国产| 亚洲自偷自拍图片 自拍| 啦啦啦免费观看视频1| 亚洲欧美日韩另类电影网站| 欧美黑人欧美精品刺激| 99久久综合精品五月天人人| 两性午夜刺激爽爽歪歪视频在线观看 | 国产亚洲精品久久久久5区| 国产精品 欧美亚洲| 日本精品一区二区三区蜜桃| 国产97色在线日韩免费| 身体一侧抽搐| 国产成人影院久久av| 在线观看www视频免费| 麻豆一二三区av精品| 亚洲av电影在线进入| 无限看片的www在线观看| av网站免费在线观看视频| 亚洲 欧美 日韩 在线 免费| 精品久久久久久电影网| 精品国产一区二区三区四区第35| 丰满迷人的少妇在线观看| 五月开心婷婷网| 老司机深夜福利视频在线观看| 一级片免费观看大全| 国产无遮挡羞羞视频在线观看| 在线国产一区二区在线| 亚洲精品久久成人aⅴ小说| 成年女人毛片免费观看观看9| 亚洲伊人色综图| 精品人妻在线不人妻| 最近最新中文字幕大全免费视频| 日韩大尺度精品在线看网址 | 久久婷婷成人综合色麻豆| 久久中文字幕一级| www.熟女人妻精品国产| 男人舔女人的私密视频| 国产精品久久久久久人妻精品电影| 精品久久久久久久久久免费视频 | 欧美激情极品国产一区二区三区| 亚洲欧美激情综合另类| 一区二区三区激情视频| 丝袜美腿诱惑在线| 精品久久久久久久久久免费视频 | 欧美日韩乱码在线| 日韩大尺度精品在线看网址 | 黄网站色视频无遮挡免费观看| 亚洲人成77777在线视频| 一级毛片女人18水好多| 黄片小视频在线播放| 免费av中文字幕在线| 麻豆久久精品国产亚洲av | 满18在线观看网站| 国产成人免费无遮挡视频| 18禁黄网站禁片午夜丰满| 女性被躁到高潮视频| 天堂中文最新版在线下载| 国产成+人综合+亚洲专区| 99久久久亚洲精品蜜臀av| 大香蕉久久成人网| 欧美精品亚洲一区二区| 国产成人精品无人区| 高清欧美精品videossex| 久久久久国内视频| 99久久久亚洲精品蜜臀av| 欧美中文日本在线观看视频| 午夜免费观看网址| 黑人操中国人逼视频| 日韩人妻精品一区2区三区| 久久婷婷成人综合色麻豆| 性欧美人与动物交配| 国产精品国产av在线观看| 丁香六月欧美| 一夜夜www| 亚洲精品在线美女| 国产单亲对白刺激| 日本精品一区二区三区蜜桃| 国产免费男女视频| 国产精华一区二区三区| 无遮挡黄片免费观看| 最新美女视频免费是黄的| 黑丝袜美女国产一区| 欧美日韩av久久| 男人操女人黄网站| 欧美久久黑人一区二区| 黄色视频,在线免费观看| 又紧又爽又黄一区二区| 日本一区二区免费在线视频| 在线观看一区二区三区| 国产aⅴ精品一区二区三区波| 免费av毛片视频| 久久热在线av| 亚洲av电影在线进入| 欧美激情久久久久久爽电影 | 欧美日韩福利视频一区二区| 亚洲自拍偷在线| 天堂影院成人在线观看| 亚洲av电影在线进入| 国产精品美女特级片免费视频播放器 | 侵犯人妻中文字幕一二三四区| 视频在线观看一区二区三区| 亚洲成人免费电影在线观看| 99国产精品一区二区蜜桃av| 午夜激情av网站| 久久久久久大精品| 国产精品98久久久久久宅男小说| 一级片免费观看大全| 亚洲五月色婷婷综合| 999久久久精品免费观看国产| 如日韩欧美国产精品一区二区三区| 999久久久精品免费观看国产| 波多野结衣一区麻豆| 脱女人内裤的视频| 人人妻,人人澡人人爽秒播| 后天国语完整版免费观看| 国产亚洲精品久久久久久毛片| 老鸭窝网址在线观看| 一本综合久久免费| 亚洲狠狠婷婷综合久久图片| 国产熟女xx| 久久人妻福利社区极品人妻图片| 午夜91福利影院| 天堂中文最新版在线下载| 色老头精品视频在线观看| av网站免费在线观看视频| 一级黄色大片毛片| 久久九九热精品免费| 黄色 视频免费看| 在线视频色国产色| 午夜免费鲁丝| 黑丝袜美女国产一区| 久久香蕉精品热| 国产精品国产高清国产av| 成人精品一区二区免费| 麻豆av在线久日| 男女午夜视频在线观看| 淫妇啪啪啪对白视频| 18禁美女被吸乳视频| 视频区欧美日本亚洲| 国产精品亚洲一级av第二区| 亚洲成国产人片在线观看| 亚洲精品美女久久av网站| 亚洲国产精品合色在线| 视频区图区小说| 91麻豆精品激情在线观看国产 | 亚洲熟妇中文字幕五十中出 | 欧美日本中文国产一区发布| 亚洲第一欧美日韩一区二区三区| 看黄色毛片网站| 90打野战视频偷拍视频| 午夜亚洲福利在线播放| 国产成+人综合+亚洲专区| 国产有黄有色有爽视频| 香蕉久久夜色| 51午夜福利影视在线观看| 老司机深夜福利视频在线观看| 国产精品爽爽va在线观看网站 | 午夜成年电影在线免费观看| 91麻豆精品激情在线观看国产 | 深夜精品福利| 国产色视频综合| 精品第一国产精品| 国产成人精品无人区| 国产深夜福利视频在线观看| 成人18禁高潮啪啪吃奶动态图| 91av网站免费观看| 国产成人欧美| 99久久精品国产亚洲精品| 精品国产一区二区三区四区第35| 丰满迷人的少妇在线观看| 日日摸夜夜添夜夜添小说| 国产黄a三级三级三级人| 丝袜美足系列| 国产伦人伦偷精品视频| 国产乱人伦免费视频| 国产成人精品无人区| 一级a爱视频在线免费观看| 免费看十八禁软件| 老司机靠b影院| 69精品国产乱码久久久| 狂野欧美激情性xxxx|