• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    熱解炭去除污水中Cr(VI)

    2016-11-22 07:41:02rkanAltunYakupKar
    新型炭材料 2016年5期
    關鍵詞:胡桃等溫線螯合

    Türkan Altun, Yakup Kar

    (1.Department of Chemical Engineering, Selcuk University, Campus, 42031Konya, Turkey;2.Department of Petroleum & Natural Gas Engineering, skenderun Technical University, 31200Hatay, Turkey)

    ?

    熱解炭去除污水中Cr(VI)

    Türkan Altun1, Yakup Kar2

    以胡桃殼在450 ℃裂解得到生物質炭BC450,以胡桃殼與20%瀝青砂在450 ℃裂解得到BCTS20,與商業活性炭(CAC)進行對比研究去除污水中Cr(VI)的能力。與BC450相比,BCTS20具有更豐富的表面官能團。在適當條件下,BC450、BCTS20、 CAC對Cr(VI)的去除率分別為80.47%、90.01%、95.69%。采用Langmuir、Freundlich、D-R 模型研究吸附等溫線,其中Langmuir模型最佳。BC450、BCTS20、CAC的最大 Langmuir吸附容量分別為36.55、49.76、51.94 mg/g。這些炭材料對Cr(VI)的吸附可能歸因于由離子交換、靜電作用與螯合作用引起的化學過程。

    熱解炭;胡桃殼;Cr(VI)

    1 Introduction

    Heavy metals are an important group of pollutants in wastewater and treated water because they have various deleterious effects on health, living organisms, and the environment. Within the heavy metal pollutant groups, Cr(VI) is one of the most dangerous inorganic water pollutants, due to its carcinogenic, mutagenic, and toxic effects[1-4]. Cr(VI) ion in discharge effluents results from many industrial activities, such as electroplating, leather tanning, cement manufacture, textile dyeing, metal processing, and the production of paint, pigments and wood preservatives[5-7]. Such industries incur significant costs in reducing the concentrations of Cr(VI) ion in industrial effluents to a permissible level of 0.05 mg/L before discharge into surface waters[8].

    The treatment technologies commonly applied for removal of Cr(VI) ion from wastewater include chemical precipitation, oxidation/reduction, filtration, ion exchange, membrane separation, and adsorption[9-11]. Among these, adsorption onto commercial activated carbons is the most common technique, owing to its advantages such as high efficiency, simplicity of design and ease of operation[12,13]. However, the process is relatively expensive because of the use of high-cost adsorbent. There is an increasing interest in lignocellulosic materials, primarily formed by various agricultural by-products such as nut shells, oily seed cakes and sawdust because such materials are renewable, abundant, and cheap. In the majority of previous studies, the biomass materials used were evaluated directly either as low-or-no-cost alternative adsorbents or as precursors for activated carbon production and bio-oil production by pyrolysis.

    With the increasing importance of bio-oil production from biomasses, it is expected that there will be abundant sources of bio-chars as by-products from pyrolysis of biomasses[14]. Bio-chars can be directly used as adsorbents for the removal of pollutants[15]owing to the abundance of oxygen/nitrogen functional groups on their surface[16], and they also have been used as precursors for activated carbon production[17,18]. However, to the best of our knowledge, very few studies have been reported on Cr(VI) removal from aqueous solutions by bio-chars obtained from pyrolysis of agricultural by-products. Mohan et al. reported that bio-chars of oak origin could remove similar amounts of Cr(VI) as activated carbons[19]. Wang et al.[20]stated that charcoal bio-char (Fe-BC) had an high adsorption capacity for Cr(VI) ion. The usability of bio-char obtained from the pyrolysis of almond shell as an alternative adsorbent in the removal of heavy metals ions ( Ni(II) and Co(II) ) by adsorption process was studied by Klet al.[21]. As a result, they reported that the bio-char can be used as an adsorbent for the removal of heavy metals from aqueous solutions. The detailed literatures on the sorption of various contaminants originated organic and inorganic by different bio-chars were summarized by Mohan et al.[22]as a critical review. Zhou et al.[23]stated that the iron modified biochar has an excellent performance for the removal of various contaminants such as heavy metals Pb(II), Cr(VI), and As(V), phosphate and methylene blue from aqueous solutions. Deveci[24]reported that the bio-chars obtained from catalytic pyrolysis of oily seeds ofPistaciaterebinthusL. with natural zeolite and alumina could be used as effective and low cost adsorbents in the removal of Cr(VI) ion from aqueous solutions.

    Walnut shell is an agricultural by-product that is suitable for the production of bio-oil by pyrolysis[25], it has a high calorific value of 20.18 MJ/kg, and potential annual availability in Turkey is estimated to be about 150 000 tons[26]. Furthermore, Nowicki et al.[27]reported that walnut shells were suitable as a precursor for producing cheap activated carbons with good adsorption properties.

    Bio-chars generated during bio-oil production via pyrolysis have useful properties in the remediation process of metals from water[17,19]. Furthermore, bio-char yields obtained from the pyrolysis of walnut shells vary between 23 wt% and 34 wt%[25]. Therefore, the evaluation of bio-chars obtained from the pyrolysis of walnut shell either as direct adsorbent or as precursor for activated bio-chars in the removal of heavy metals from aqueous media will increase the range of applications and add value to the country's economy.

    The objective of this study is to investigate the adsorption capacity of bio-chars in the removal Cr(VI) ion from aqueous solution. The adsorption capacities of bio-chars were compared with that of commercial activated carbon via batch studies by a systematic evaluation of effective parameters such as pH, contact time, chromium concentration, adsorbent dose, and temperature. Freundlich, Langmuir, and D-R isotherms were used to examine the kinetics of adsorption and to calculate isotherm parameters.

    2 Experimental

    2.1 Materials

    All chemicals and reagents used in the present study were of analytical grade (Merck KGaA, Darmstadt, Germany). Stock solution Cr (VI) of 1 000 mg/L was prepared by dissolving the exact quantity of K2Cr2O7in 1 000 mL of deionized-distilled water. The Cr (VI) solution of 55 mg/L used as adsorbate was prepared by diluting the stock solution immediately prior to use. The pH value of the solution was adjusted by 0.1 mol/L NaOH or 0.1 mol/L HNO3.

    Bio-chars (abbreviated as BC450 and BCTS20) were obtained from pyrolysis of walnut shell alone and in combination with tar sand (20 wt%) in a previous study, respectively[25], and also CAC (commercial activated carbon) were used for comparison. The bio-chars were used directly, without being subjected to any upgrading.Before use, the bio-chars samples were stored in glass bottles.

    2.2 Apparatus

    The surface morphology of the BC450 and BCTS20 samples were examined by scanning electron microscopy (LEO EVO 40 SEM). The FT-IR spectra of the bio-chars were recorded using a FT-IR Spectrometer (Perkin Elmer Spectrum 100). An elemental analyzer (LECO CHNS 932) was used to determine the elemental contents of the bio-chars. The pH values for the test solution of Cr(VI) were adjusted with an Orion pH meter (model 900S2). A thermostatic shaker (model GFL 3033) and magnetic stirrer (model IKAMAG-RO15) were used in the adsorption experiments. Cr(VI) concentration after adsorption was determined by a UV-vis Spectrophotometer (Shimadzu UV-1700) at 540 nm.

    2.3 Batch adsorption experiments

    Batch adsorption experiments were performed according to an established method described in detail in previous studies[4,28〗[29]. The amounts of Cr(VI) ions loaded on the particles of BC450, BCTS20, and CAC were calculated by conducting a mass balance on the solute before and after each experiment. For each adsorbent, all experiments were performed in triplicate and average results were reported.

    The effects of the different initial pH values (range 2-9) on adsorption were studied under 0.05 g of adsorbent, 25 mL of test solution at a concentration of 55 mg/L, temperature of 25±1 ℃, and contact time of 60 min.To examine the effects of the contact time (range 10-240 min), the experiments were performed at pH 2, with all other variables identical above. Adsorption isotherms were studied at different initial Cr(VI) concentrations between 10 and 65 mg/L by holding other variables constant (0.05 g of adsorbent, 25 mL of test solution, pH 2, 25±1 ℃, and contact time of 60 min). The fourth series of experiments were performed to examine the effects of adsorbent dosage, varying from 0.002 to 0.12 g, with other parameters as defined in the previous series. To determine the effect of temperature on the adsorption process, the last series experiments was carried out at temperature of 25, 35, and 65±1 ℃, with other conditions as in the third group.

    3 Results and discussion

    3.1 Characterization of the bio-chars

    Elemental analysis of C, H, N, S, and O (by difference) was performed for the BC450 and BCTS20 bio-chars. The elemental analysis results were then used to calculate the H/C molar ratios of the bio-chars. All results are shown in Table 1. When the elemental contents of the bio-chars are compared with those of the walnut shell and tar sand reported in a previous study[25], it was seen that the bio-chars (BC450 and BCTS20) are richer in carbon content, at 76.93wt% and 68.57wt%, respectively. The H/C molar ratio of BCTS20 was slightly higher than that of BC450. The higher H/C ratio of BCTS20 suggests it will have a greater adsorption capacity[30].

    Table 1 Elemental contents and molar ratios for the bio-chars.

    *Calculated by difference.

    In order to determine the functional groups involved in Cr (VI) adsorption, the FT-IR spectra of the bio-chars are compared (Fig. 1). Comparison of the spectra in Fig. 1 shows that the surface chemistries of bio-chars are quite different in terms of the functional groups on their surfaces. BCTS20 includes important active groups like —CH, N—H, and C—O, which are involved in the adsorption of Cr(VI)[13]. The spectrum indicates that these functional groups correspond to the bands occurring in range of 2 937-2 967, 1 462, and 1 085 cm-1, respectively. The results reveal that the addition of tar sand to the pyrolysis process produces a significant effect on the surface properties of char product.

    Fig. 1 FT-IR spectra of pyrolytic charcoals: BC450 and BCTS20.

    Morphological analysis of the surface of the bio-chars was carried out by scanning electron microscopy. Scanning electron micrographs of bio-chars BC450 and BCTS20 are illustrated in Fig. 2 a,b. The SEM micrograph of BC450 clearly shows that the BC450 has an amorphous and heterogeneous structure, with many rudimentary and randomly distributed fine pores within its structure. In contrast, Fig. 2(b) reveals that the BCTS20 has a highly homogeneous structure with a predominance of mesopores, which have a major role in many liquid-solid adsorption processes[19].

    Fig. 2 SEM micrographs of (a) BC450 and (b) BCTS20.

    3.2 Effect of pH on Cr(VI) ion removal

    To determine the effect of pH on the removal of Cr(VI) from aqueous media by the bio-chars (BC450 and BCTS20) and commercial activated carbon (CAC, Merck), a series of adsorption experiments were performed. The results in Fig. 3 show that the maximum Cr (VI) adsorption values for BC450, BCTS20, and CAC are 80.47%, 90.01%, and 95.69% respectively at about pH 2.0. Adsorption percentages of all adsorbents decreases sharply when pH was increased from 2.0 to 5.0, then levelled off with a further increase of pH values.

    Fig. 3 Effect of pH value on Cr (VI) removal by the charcoals.

    The effect of pH on the removal of chromium ion from aqueous media is associated with the interactions between the chromium ion and the bio-char walls and also the complexes present on the sorbent surface[19]. As reported by many studies[32,33], the high chromium removal attained at low pH values can be explained by strong acidic conditions that cause a highly protonated adsorbent surface, which results in a high uptake of Cr (VI) in the anionic form. This is because a more protonated surface produces stronger electrostatic attraction between the positively-charged sorbent surface and negatively-charged chromate ion. The decrease in adsorption efficiency at pH>5.0 may be attributed to the weakening of electrostatic attraction between the sorbents and the sorbate ions owing to the dual competition of chromate and hydroxyl ions to be adsorbed on the surface of the sorbents[31-35]. Therefore, subsequent adsorption studies of the optimal values for other operating parameters were carried out at the optimal pHintof 2.0. This agrees with many earlier studies of the removal of Cr(VI) ion by different bio-chars, in which the optimal pH value was reported as 2.0[19,32,34,36].

    3.3 Effect of contact time on Cr(VI) ion removal

    Optimal contact time is a significant parameter in terms of the total cost of the adsorption process, because the shaking process used during adsorption involves energy consumption. A series of contact-time experiments was carried out at optimal pH 2 with a contact time ranging from 10 to 240 min, and all other conditions held constant (Fig. 4).

    Fig. 4 Effect of contact time on Cr (VI) removal capacity by the charcoals.

    For all adsorbents, the percentage removal of Cr(VI) ion increased with contact time from 10-60 min, and reached a maximum value at a contact time of 60 min. There was a negligible increase in the adsorption percentage above 60 min. At the optimal contact time of 60 min, the adsorption percentages were 80.51% for BC450, 96.25% for CAC, and 89.80% for BCTS20. On the basis of these results, a contact time of 60 min was adopted as the optimal shaking period in the subsequent studies.

    High adsorption rates were recorded up to the optimal contact time of 60 min because of the abundance of free binding sites. During the initial stage of adsorption, mesopores are largely saturated with chromium ions. During later stages, the adsorption rate was very slow because Cr (VI) ions are forced to migrate deep into the micropores, resulting in much a great resistance[37].

    3.4 Effect of sorbent dose on Cr(VI) ion removal

    The relationship was established between the sorbent dose and the percentage removal of Cr(VI) ion. A series of adsorption experiments were performed on the treatment of required sorbents (BC450, CAC and BCTS20) in mass range of 0.002-0.130 g with 25 mL of Cr(VI) solution in 55 ppm. All adsorption experiments were carried out at the two optimized conditions in previous series (pHint2 and contact time of 60 min). The results are given in Fig. 5. For all sorbents, Cr (VI) adsorption percentage increased with sorbent dose, reached a maximum at 0.064 g/25 mL sorbent dose, and then remained almost constant for a further increase in sorbent dose.

    The results can be attributed to the occurrence of great surface area and an increase in the number of binding sites[36-38]. In this stage, the highest Cr(VI) removal efficiencies obtained at the optimal sorbent dose were 81.82%, 95.64% and 92.15% for BC450, CAC, and BCTS20, respectively. The difference in the Cr(VI) removal capacities of the sorbents could be attributed to the diversity of active groups on the sorbent surface and the variation in their concentration[39].

    Fig. 5 Effect of adsorbent concentration on Cr (VI) removal.

    3.5 Influence of initial concentration on Cr (VI) removal

    To determine the effect of initial concentration of Cr(VI) solution on the removal of Cr(VI) ion by bio-chars, a series of adsorption experiments were performed on each sorbent (BC450, CAC, and BCTS20) with initial solution concentrations ranging from 10 to 65 mg/L under the optimal conditions (2.65 g/L sorbent dose, pHint2, and 60 min of contact time). With an increase in initial concentration of Cr (VI) solution (Ci, Mm), the Cr(VI) uptake (per their mass at equilibrium (qe, mmol/g)) of all the sorbents increased, their percentage adsorption values decreased. The increase inqevalues of all the sorbents was significant up toCi= 55 mg/L (1.058 mM) due to the great availability of active sites on the sorbent at low initial solution concentrations, resulting from a high driving force[37], but was then negligible with a further increase of the concentrations.

    3.6 Adsorption isotherms

    Adsorption isotherms or capacity studies are very important in calculating the amounts of metal ions partitioned between sorbent and liquid phase at equilibrium as a function of increase in metal ion concentration[40].

    Isotherm models represent the best fitting to the adsorption of Cr(VI) ions by each sorbent (BC450, CAC, and BCTS20). The isotherms were analyzed using Freundlich, Langmuir, and D-R (Dubinin-Radushkevich) models. The Langmuir model is given in Eq. (1).

    (1)

    where,Ceandqeare the solute concentration and uptake value of metal ion of sorbent per its mass respectively;As(mol/g) andKb(L/mol) are the coefficients.

    Another common isotherm is the Freundlich model described in Eq. (2).

    (2)

    wherekandnare constants.

    The D-R isotherm model is expressed in Eq. (3).

    lnqe=lnX'm-K'×ε2

    (3)

    whereX'm(mmol/g) andK'(mol2/kJ2) are the maximum adsorption capacity of sorbent and a constant related to the adsorption energy, respectively;εis the Polanyi potential, which is expressed as follows:

    whereR(kJ/mol×K) is the gas constant andTis absolute temperature. The magnitude of mean adsorption energy (E, kJ/mol) is useful to estimate the type of adsorption process, and can be determined using the following equation:

    For all the sorbents, Table 2 shows the model parameters and correlation coefficients (R2) . As seen in Table 2, theR2of the Langmuir isotherm for each of the sorbents was greater than the other models, which indicates that the Langmuir isotherm represents best the adsorption of Cr(VI) onto the bio-chars. This result is an indication of the adsorption of Cr(VI) ions onto a monolayer of the surfaces of BC450 and BCTS20 under the experimental conditions. From the fitted Langmuir model, the maximum adsorption capacities are 36.55, 49.76, and 51.94 mg/g of BC450, BCTS20, and CAC, respectively.

    Table 2 Isotherms model constants for BC450, BCTS20 and CAC.

    a: mmol/g dry sorbent.

    The favorability of a adsorption process can be expressed according to the magnitude ofRLfrom Langmuir constant (Kb), which is determined from the following equation[13,36,42]and called as the dimensionless separation factor.

    For 55 mg/L (1.058 Mm of the optimalCi), theRLvalues for BC450, BCTS20, and CAC were calculated as 0.00351, 0.00172 and 0.00085, respectively. These results indicate that the adsorption process was favorable, because 0

    Langmuir isotherm constants are not sufficient to explain whether the type of adsorption is either physical or chemical[41]. However, the magnitude of mean adsorption energy (E); which is calculated from the D-R isotherm, is a useful indicator of the type of adsorption process[44]. From Table 2, it is seen that the values ofEfor all sorbent were within the range 8-16 kJ/mol, which indicates a chemical adsorption, dominated by ion-exchange, electrostatic attraction and chelation[41].

    3.7 Adsorption kinetics

    Adsorption kinetics is important in the modeling and design of adsorption process[45]. Many kinetic studies using experimental data for the removal of Cr(VI) by various carbonaceous materials have previously reported that the kinetic of the adsorption process was compatible with the pseudo-second-order model[13,31,36]. Therefore, only the suitability of experimental data to the pseudo-second-order model was examined, using the pseudo-second order equation[46]given in Eq. (4).

    (4)

    wherek2(g/mg×min) andqt(mg/g) are the rate constant of the pseudo-second-order kinetic equation and the amount of Cr(VI) removed at any time (t, min), respectively.

    Table 3 shows the results obtained for the adsorption kinetics, showing that the values ofqecalculated from the pseudo-second-order kinetics model (termedqe,cal,) were nearly equal to the experimental values ofqe(marked asqe,exp). Also, theR2values were very close to 1.0, indicating that the adsorption kinetic is consistent with the pseudo-second-order kinetic model. As a result, the compatibility of experimental data with the pseudo-second-order kinetics model confirms that chemisorption is likely dominant in the removal of Cr(VI) by BC450, BCTS20, and CAC. This result is in accordance with other studies[13,19,47].

    3.8 Effect of temperature and the adsorption thermodynamics

    In order to determine the effect of temperature on the adsorption process, a series of adsorption experiments were carried out within the temperature range 25-65 ℃ with other parameters held constant at the optimal values already determined above. The thermodynamic parameters, including standard Gibbs free energy change (ΔG0), standard enthalpy change (ΔH0), and standard entropy change (ΔS0) were calculated using the following equations[41,48]:

    ΔG0=-RTlnKc

    (5)

    (6)

    (7)

    whereCAeandKcare the adsorbent concentration at equilibrium and the equilibrium constant, respectively.

    Table 3 Results of the pseudo-second order kinetic model for the removal of Cr(VI) by BC450, BCTS20 and CAC.

    The magnitudes of thermodynamic parameters (ΔH0andΔS0) were calculated from the slope and intercept of the linear plots of LogKcversus 1/T, respectively.

    The values of thermodynamic parameters calculated for the removal of Cr(VI) by the sorbents are given in Table 4. In general, the negative value ofΔG0is an indicator for the feasibility and spontaneous nature of adsorption process[36,41,44]. From the results in Table 4, it was seen that there was a continuous increase in the negative values ofΔG0with increasing temperature from 25 to 65 ℃. As a result, it may be suggested that the process of Cr(VI) on the sorbents was spontaneous, and that the degree of spontaneity increased with temperature, resulting in a more negative value ofΔG0at a higher temperature. The more negative value indicates a more energetically favorable adsorption process[39].

    Table 4 Thermodynamic parameters for the removal of Cr(VI) by the bio-chars and CAC.

    3.9 Comparison of adsorption capacities of bio-chars with other sorbents

    An increasing number of studies have examined the removal of Cr(VI) ion from aqueous medium by various low-cost materials such as biomass, bio-char, and activated bio-char. Table 5 compares the adsorption capacities reported for the various sorbents used for removal of Cr(VI)[19,20,28,32,34,36,41,44,51-54].

    Table 5 Comparison of the maximum adsorption capacities(Langmuir isotherm) of bio-chars with other sorbents for Cr(VI) removal.

    The positive values forΔH0andΔS0for all sorbents show that the adsorption process carried out under experimental conditions is endothermic. Moreover, the positive values of bothΔH0andΔS0indicate that chemisorption is the dominant mechanism of Cr(VI) adsorption on the bio-chars and CAC. In addition, the positive value ofΔS0indicates that the adsorption process is irreversible and stable[49,50]. These results are similar to those previously reported for the removal of Cr(VI) by various carbonaceous materials[36,44].

    Compared to the values reported in the literatures, the bio-chars used in the present study appear to be a highly efficient sorbent for the removal of Cr(VI) ion from aqueous solutions.

    4 Conclusions

    The SEM and FT-IR results reveal that the use of tar sand as an additive during pyrolysis led to the formation of a large amount of surface functional groups of the resulting bio-chars. The removal of Cr(VI) from aqueous solution by the bio-chars was dependent on pH, initial Cr(VI) concentration, bio-char dose, contact time. And the maximum removal of Cr(VI) achieved by the bio-chars was 80.47% for BC450, 90.01% for BCTS20 and 95.69% for CAC at about pH 2. The bio-chars prepared in the present study are superior to many sorbents that were previously reported for the removal of Cr(VI) in terms of adsorption capacity. The bio-chars tested in the present study (BC450 and BCTS20) can be used effectively for the remediation of chromium-polluted wastewater streams.

    [1] Liu W, Zhang J, Zhang, C, et al. Adsorptive removal of Cr (VI) by Fe-modified activated carbon prepared from trapa natans husk[J]. Chemical Engineering Journal, 2010, 162: 677-684.

    [2] Sikaily E A, Nemr A E, Khaled A, et al. Removal of toxic chromium from waste water using green alga ulva lactuca and its activated carbon[J]. Journal of Hazardous Materials, 2007, 148: 216-228.

    [3] Li H, Li Z, Liu T, et al. A novel technology for biosorption and recovery of hexavalent chromium in wastewater by bio-functional magnetic beads[J]. Bioresource Technology, 2008, 99: 6271-6279.

    [4] Arslan G, Edebali S, Pehlivan E. Physical and chemical factors affecting the adsorption of Cr(VI) via humic acids extracted from brown coals[J]. Desalination, 2010: 255, 117-123.

    [5] Kim S D, Park K S, Gu M B. Toxicity of hexavalent chromium to daphnia magna: influence of reduction reaction by ferrous iron[J]. Journal of Hazardous Materials, 2002, A93: 155-164.

    [6] D?nmez G, Aksu Z. Removal of chromium (VI) from salina wastewaters by dunaliella species[J]. Process Biochemistry, 2002, 38: 751-762.

    [7] Gottipati R, Mishra S. Process optimization of adsorption of Cr (VI) on activated carbons prepared from plant precursors by a two-level full factorial design[J]. Chemical Engineering Journal, 2010, 160: 99-107.

    [8] Baral A, Engelken R D. Chromium-based regulations and greening in metal finishing industries in the USA[J]. Environmental Science and Policy, 2002, 5: 121-133.

    [9] Terry P A. Characterization of Cr ion exchange with hydrotalcite[J]. Chemosphere, 2004, 57: 541-546.

    [10] ?lmez T. The optimization of Cr(VI) reduction and removal by electrocoagulation using response surface methodology[J]. Journal of Hazardous Materials, 2009, 162: 1371-1378.

    [11] Alguacil F J, Caravaca C, Martin M I. Transport of chromium(VI) through a cyanex 921-supported liquid membrane from HCI solutions[J]. Journal of Chemical Technology and Biotechnology, 2003, 78: 1048-1053.

    [13] Moussavi G, Barikbin B. Biosorption of chromium (VI) from industrial wastewater onto pistachio hull waste biomass[J]. Chemical Engineering Journal, 2010, 162: 893-900.

    [14] Liu Z, Zhang F S. Removal of copper (II) and phenol from aqueous solution using porous carbons derived from hydrothermal chars[J]. Desalination, 2011, 267: 101-106.

    [15] Liu W J, Zeng F X, Jiang H, et al. Preparation of high adsorption capacity bio-chars from waste biomass[J]. Bioresource Technology, 2011, 102: 8247-8252.

    [16] Cheng H N, Wartelle L H, Klasson K T, et al. Solid-state NMR and ESR studies of activated carbons produced from pecan shells[J]. Carbon, 2010, 48: 2455-2469.

    [17] Mohan D, Pittman J C U, Bricka M, et al. Sorption of arsenic, cadmium, and lead by chars produced from fast pyrolysis of wood and bark during bio-oil production[J]. Journal of Colloid Interface Science, 2007, 310: 57-73.

    [18] Cao N, Darmstadt H, Roy C. Activated carbon produced from charcoal obtained by vacuum pyrolysis of softwood bark residues[J]. Energy Fuels, 2001, 15: 1263-1269.

    [19] Mohan D, Rajput S, Singh V K, et al. Modeling and evaluation of chromium remediation from water using low cost bio-char, a green adsorbent[J]. Journal of Hazardous Materials, 2011, 188: 319-333.

    [20] Wang X J, Wang Y, Wang X, et al. Microwave-assisted preparation of bomboo charcoal-based iron-containing adsorbents for Cr(VI) removal[J]. Chemical Engineering Journal, 2011, 174: 326-332.

    [22] Mohan D, Sarswat A, Ok Y S, et al. Organic and inorganic contaminants removal from water with biochar, a renewable, low cost and sustainable adsorbent-A critical review[J]. Bioresource Technology, 2014, 160: 191-202.

    [23] Zhou Y, Gao B, Zimmerman A R, et al. Biochar-supported zerovalent iron for removal of various contaminants from aqueous solutions[J]. Bioresource Technology, 2014, 152: 538-542.

    [24] Deveci H, Kar Y. Adsorption of hexavalent chromium from aqueous solutions by bio-chars obtained during biomass pyrolysis[J]. Journal of Industrial and Engineering Chemistry, 2013, 19: 190-196.

    [25] Kar Y. Co-pyrolysis of walnut shell and tar sand in a fixed-bed reactor[J]. Bioresource Technology, 2011, 102: 9800-9805.

    [27] Nowicki P, Pietrzak R, Wachowska H. Sorption properties of activated carbons obtained from walnut shells by chemical and physical activation[J]. Catalysis Today, 2010, 150: 107-114.

    [28] Pehlivan E, Altun T. Biosorption of chromium (VI) ion from aqueous solutions using walnut, hazelnut and almond shell[J]. Journal of Hazardous Materials, 2008, 155: 378-384.

    [29] APHA. Standard methods for the examination of water and wastewater[S]. 17thed, APHA-WWA-WPCF, vol. 3, 1989.

    [30] Raveendran K, Ganesh A. Adsorption characteristics and pore-development of biomass-pyrolysis char[J]. Fuel, 1998, 77: 769-781.

    [31] Nameni M, Alavi Moghadam M R, Arami M. Adsorption of hexavalent chromium from aqueous solutions by wheat bran[J]. International Journal of Environmental Science and Technology, 2008, 5: 161-168.

    [32] Mor S, Ravindra K, Bishnoi N R. Adsorption of chromium from aqueous solution by activated alumina and activated charcoal[J]. Bioresource Technology, 2007, 98: 954-957.

    [33] Karthikeyan T, Rajgopal S, Miranda L R. Chromium (VI) adsorption from aqueous solution by hevea brasilinesis sawdust activated carbon[J]. Journal of Hazardous Materials, 2005, B124: 192-199.

    [34] Pehlivan E, Kahraman H, Pehlivan E. Sorption equilibrium of Cr(VI) ions on oak wood charcoal (Carbo Ligni) and charcoal ash as low-cost adsorbents[J]. Fuel Processing Technology, 2011, 92: 65-70.

    [35] Baral S S, Dasa S N, Rath P. Hexavalent chromium removal from aqueous solution by adsorption on treated sawdust[J]. Biochemical Engineering Journal, 2006, 31: 216-222.

    [36] Jain M, Garg V K, Kadirvelu K. Adsorption of hexavalent chromium from aqueous medium onto carbonaceous adsorbents prepared from waste biomass[J]. Journal of Environmental Management, 2010, 91: 949-957.

    [37] Wang F Y, Wang H, Ma J W. Adsorption of cadmium (II) ions from aqueous solution by a new low-cost adsorbent-bamboo charcoal[J]. Journal of Hazardous Materials, 2010, 177: 300-306.

    [38] Bansal M, Singh D, Garg V K. A comparative study for the removal of hexavalent chromium from aqueous solution by agricultural wastes’carbons[J]. Journal of Hazardous Materials, 2009, 171: 83-92.

    [39] Dakiky M, Khamis M, Manassra A, et al. Selective adsorption of chromium(VI) in industrial wastewater using low-cost abundantly available adsorbents[J]. Advances in Environmental Research, 2002, 6: 533-540.

    [40] Karatas M. Removal of Pb(II) from water by natural zeolitic tuff: kinetics and thermodynamics[J]. Journal of Hazardous Materials, 2012, 199-200: 383-389.

    [41] Altun T, Pehlivan E. Removal of Cr(VI) from aqueous solutions by modified walnut shells[J]. Food Chemistry, 2012, 132: 693-700.

    [42] Kadirvelu K, Thamaraiselvi K, Namasivayam C. Adsorption of nickel (II) from aqueous solution onto activated carbon prepared from coir pith[J]. Separation and Purification Technology, 2001, 24: 497-505.

    [43] Babel S, Kurniawan T A. Cr(VI) removal from synthetic wastewater using coconut shell charcoal and commercial activated carbon modified with oxidizing agents and/or chitosan[J]. Chemosphere, 2004, 54: 951-967.

    [46] Ho Y S, Mckay G. Pseudo-second order model for sorption processes[J]. Process Biochemistry, 1999, 34: 451-465.

    [47] Wang X S, Chen L F, Li F Y, et al. Removal of Cr(VI) with wheat-residue derived black carbon: Reaction mechanism and adsorption performance[J]. Journal of Hazardous Materials, 2010, 175: 816-822.

    [48] Romero-Gonzalez J, Peralta-Videa J R, Rodriguez E. Determination of thermodynamic parameters of Cr(VI) adsorption from aqueous solution onto Agave lechuguilla biomass[J]. The Journal of Chemical Thermodynamics, 2005, 37: 343-347.

    [49] Panda L, Das B, Rao D S, et al. Application of dolochar in the removal of cadmium and hexavalent chromium ions from aqueous solutions[J]. Journal of Hazardous Materials, 2011, 192: 822-831.

    [50] Singh D B, Prasad G, Rupainwar D C. Adsorption technique for the treatment of As (V) rich effluents[J]. Colloids and Surfaces, 1996, A 111: 49-56.

    [51] Seyf-laye Alfa-Sika M, Liu F, Chen H. Optimization of key parameters for chromium (VI) removal from aqueous solutions using activated charcoal[J]. Journal of Soil Science and Environmental Management, 2010, 1(3): 55-62.

    [52] Anandkumar J, Mandal B. Removal of Cr(VI) from aqueous solution using bael fruit (Aegle marmelos correa) shell as an adsorbent[J]. Journal of Hazardous Materials, 2010, 168: 633-640.

    [53] Dubey S P, Gopal K. Adsorption of chromium (VI) on low cost adsorbents derived from agricultural waste material: a comparative study[J]. Journal of Hazardous Materials, 2007, 145: 465-470.

    [54] Hamadi N K, Chen X D, Farid M M, et al. Adsorption kinetics for the removal of chromium (VI) from aqueous solution by adsorbent derived from used tyres and sawdust[J]. Chemical Engineering Journal, 2001, 84: 95-105.

    Removal of Cr(VI) from aqueous solution by pyrolytic charcoals

    Türkan Altun1, Yakup Kar2

    Bio-chars produced by the pyrolysis of walnut shells at 450 ℃ (BC450) and theco-pyrolysis of walnut shells and 20 wt% tar sand (BCTS20)at the same temperature, were investigated as potential adsorbents for the removal of Cr(VI) ions from aqueous solutions using batch experiments. The BCTS20 has more abundant surface functional groups than BC450. The Cr(VI) removal percentages under optimal conditions were 80.47and 95.69% for BC450 and BCTS20, respectively. Langmuir, Freundlich and D-R models were used to fit the adsorption isotherms and the Langmuir model described the adsorption isotherms best. The adsorption of Cr(VI) was by a chemical process dominated by ion-exchange, electrostatic attraction and chelation. The maximum Langmuir adsorption capacities were 36.55 and 49.76 mg per g of BC450 and BCTS20, respectively. The maximum Langmuir adsorption capacity of BCTS20 is comparable to that of some reported commercial activated carbons.

    Pyrolytic charcoal; Walnut shell; Hexavalent chromium

    Yakup Kar. E-mail: karyakup@gmail.com

    Yakup Kar. E-mail: karyakup@gmail.com

    1007-8827(2016)05-0501-09

    TQ127.1+1

    A

    10.1016/S1872-5805(16)60028-8

    Receiveddate: 2016-07-01;Reviseddate: 2016-09-15

    English edition available online ScienceDirect ( http:www.sciencedirect.comsciencejournal18725805 ).

    猜你喜歡
    胡桃等溫線螯合
    玉米低聚肽螯合鐵(II)的制備和結構表征
    低溫吸附劑的低溫低壓吸附等溫線分布研究
    不同結構的烏鱧螯合肽對抗氧化活性的影響
    胡桃夾子和四個王國
    胡桃夾子
    學與玩(2017年4期)2017-02-16 07:05:44
    胡桃夾子
    螯合型洗滌助劑檸檬酸一氫鈉與Ca2+離子螯合機理的理論研究
    如何在新課改背景下突破等溫線判讀中的難點
    胡桃夾子的規律
    新少年(2014年8期)2014-07-23 02:15:08
    正交試驗優化膠原多肽螯合鈣的制備工藝
    亚洲在线自拍视频| 在线观看免费视频日本深夜| 日日夜夜操网爽| www.www免费av| 身体一侧抽搐| 精品第一国产精品| 最近视频中文字幕2019在线8| 国产亚洲av嫩草精品影院| 久久久水蜜桃国产精品网| 国产爱豆传媒在线观看 | 可以在线观看毛片的网站| 欧美日韩一级在线毛片| 色av中文字幕| 成人午夜高清在线视频| a级毛片a级免费在线| 十八禁网站免费在线| 国产91精品成人一区二区三区| 波多野结衣巨乳人妻| 级片在线观看| 在线观看午夜福利视频| 国产精品av久久久久免费| av欧美777| 亚洲av成人不卡在线观看播放网| 午夜两性在线视频| 黄色毛片三级朝国网站| 在线观看免费午夜福利视频| 两性夫妻黄色片| 日本免费a在线| 国产真人三级小视频在线观看| 三级国产精品欧美在线观看 | 色综合婷婷激情| 免费在线观看日本一区| 在线观看免费午夜福利视频| x7x7x7水蜜桃| 国产精华一区二区三区| 欧美成人一区二区免费高清观看 | 欧美日韩中文字幕国产精品一区二区三区| 神马国产精品三级电影在线观看 | 国产黄色小视频在线观看| 久久久久久久精品吃奶| 久久精品91无色码中文字幕| 变态另类丝袜制服| 岛国视频午夜一区免费看| 日本五十路高清| 精品国产超薄肉色丝袜足j| 亚洲色图av天堂| 亚洲av成人精品一区久久| 两人在一起打扑克的视频| 精品国产乱码久久久久久男人| 久久久久久大精品| 久久中文看片网| 亚洲成人中文字幕在线播放| 久久久久久人人人人人| 国产爱豆传媒在线观看 | bbb黄色大片| 色综合欧美亚洲国产小说| 亚洲第一欧美日韩一区二区三区| 在线观看美女被高潮喷水网站 | 一二三四社区在线视频社区8| 最好的美女福利视频网| 99热只有精品国产| 日本免费a在线| 热99re8久久精品国产| √禁漫天堂资源中文www| 欧美高清成人免费视频www| 妹子高潮喷水视频| avwww免费| 欧美性猛交╳xxx乱大交人| a级毛片在线看网站| 亚洲成a人片在线一区二区| 国产av麻豆久久久久久久| 国产精品一区二区三区四区免费观看 | av在线天堂中文字幕| 国产不卡一卡二| 男女下面进入的视频免费午夜| 美女大奶头视频| 无遮挡黄片免费观看| 久久精品人妻少妇| 亚洲精品一区av在线观看| 国产成人系列免费观看| 欧美在线黄色| 亚洲国产精品sss在线观看| 美女免费视频网站| 午夜福利高清视频| 国产精品久久久久久亚洲av鲁大| 国产三级在线视频| 99国产极品粉嫩在线观看| 无遮挡黄片免费观看| av欧美777| 国产av一区二区精品久久| 婷婷六月久久综合丁香| 美女高潮喷水抽搐中文字幕| 久久中文看片网| 极品教师在线免费播放| 中文字幕熟女人妻在线| 久久精品影院6| 99国产极品粉嫩在线观看| 国产精品日韩av在线免费观看| 国产黄色小视频在线观看| aaaaa片日本免费| 久久久精品大字幕| 国产亚洲精品一区二区www| 久久精品91蜜桃| 在线视频色国产色| 变态另类丝袜制服| 欧美乱妇无乱码| 色综合欧美亚洲国产小说| 一本精品99久久精品77| 免费在线观看视频国产中文字幕亚洲| 亚洲专区中文字幕在线| 丰满人妻一区二区三区视频av | 国产探花在线观看一区二区| 亚洲中文字幕一区二区三区有码在线看 | xxxwww97欧美| 亚洲av中文字字幕乱码综合| 国产精品久久久久久久电影 | www.精华液| 成人欧美大片| 女同久久另类99精品国产91| 91麻豆精品激情在线观看国产| 久久天躁狠狠躁夜夜2o2o| 国产精品av久久久久免费| 欧美日韩一级在线毛片| 天堂影院成人在线观看| 欧美日韩精品网址| 美女大奶头视频| 久久久久久久午夜电影| 亚洲五月婷婷丁香| 久久久国产成人精品二区| 啦啦啦韩国在线观看视频| 久热爱精品视频在线9| 每晚都被弄得嗷嗷叫到高潮| 久久亚洲精品不卡| 亚洲av日韩精品久久久久久密| а√天堂www在线а√下载| 久99久视频精品免费| 欧美国产日韩亚洲一区| 国产成人欧美在线观看| 亚洲精品在线观看二区| 麻豆一二三区av精品| 人妻丰满熟妇av一区二区三区| 在线看三级毛片| 国产精品一区二区免费欧美| 女同久久另类99精品国产91| 美女免费视频网站| 欧美成人性av电影在线观看| 亚洲成人久久爱视频| 国产精品免费视频内射| 黑人操中国人逼视频| 成人永久免费在线观看视频| 国产精品1区2区在线观看.| 好男人电影高清在线观看| 五月伊人婷婷丁香| 麻豆国产97在线/欧美 | 精品久久久久久久毛片微露脸| 久久久久九九精品影院| 国产精品久久电影中文字幕| 亚洲熟妇中文字幕五十中出| 两性午夜刺激爽爽歪歪视频在线观看 | 看片在线看免费视频| 好男人电影高清在线观看| 亚洲精品在线美女| 日韩成人在线观看一区二区三区| 变态另类丝袜制服| 久久婷婷人人爽人人干人人爱| 99国产精品一区二区蜜桃av| 久久精品综合一区二区三区| www.www免费av| 国产精品久久视频播放| 中国美女看黄片| 欧美日韩福利视频一区二区| 国模一区二区三区四区视频 | 亚洲一码二码三码区别大吗| 亚洲国产精品久久男人天堂| 熟女少妇亚洲综合色aaa.| 在线播放国产精品三级| 亚洲成av人片在线播放无| 一区二区三区激情视频| 丰满的人妻完整版| 99国产综合亚洲精品| 两性夫妻黄色片| 亚洲avbb在线观看| 一区二区三区国产精品乱码| 三级男女做爰猛烈吃奶摸视频| 日韩欧美精品v在线| 99热只有精品国产| 精品免费久久久久久久清纯| 男人的好看免费观看在线视频 | 天天躁夜夜躁狠狠躁躁| 国产成年人精品一区二区| 日韩有码中文字幕| 中文字幕最新亚洲高清| 999久久久精品免费观看国产| 欧美黄色片欧美黄色片| 久久久国产成人免费| 一级毛片女人18水好多| 亚洲专区中文字幕在线| 视频区欧美日本亚洲| 女人被狂操c到高潮| 亚洲av五月六月丁香网| 免费av毛片视频| 免费观看人在逋| 欧美日韩福利视频一区二区| 香蕉久久夜色| 色在线成人网| cao死你这个sao货| 中文字幕最新亚洲高清| 熟女电影av网| 久久久水蜜桃国产精品网| bbb黄色大片| 人人妻人人看人人澡| 亚洲 欧美 日韩 在线 免费| av中文乱码字幕在线| 久久天堂一区二区三区四区| 一夜夜www| 99国产精品一区二区蜜桃av| 久久午夜综合久久蜜桃| 男女那种视频在线观看| 久久这里只有精品19| 午夜久久久久精精品| 日本黄大片高清| 久久精品国产亚洲av香蕉五月| 午夜亚洲福利在线播放| 亚洲一卡2卡3卡4卡5卡精品中文| 亚洲国产中文字幕在线视频| 级片在线观看| 小说图片视频综合网站| 91麻豆精品激情在线观看国产| 色播亚洲综合网| 非洲黑人性xxxx精品又粗又长| 欧美日韩亚洲国产一区二区在线观看| 国产99久久九九免费精品| 亚洲一区二区三区不卡视频| 不卡一级毛片| 精华霜和精华液先用哪个| 国产午夜精品久久久久久| 日本一二三区视频观看| 亚洲在线自拍视频| 不卡一级毛片| 国产蜜桃级精品一区二区三区| 天堂√8在线中文| 久久久久国内视频| 国产在线精品亚洲第一网站| 搡老熟女国产l中国老女人| 身体一侧抽搐| 亚洲精品国产精品久久久不卡| 日韩有码中文字幕| 国内精品久久久久精免费| 欧美精品亚洲一区二区| 日韩欧美精品v在线| 麻豆av在线久日| 久久伊人香网站| 亚洲国产精品合色在线| 999精品在线视频| 国产高清视频在线播放一区| 99久久精品热视频| 狠狠狠狠99中文字幕| 成人av在线播放网站| 国产久久久一区二区三区| 国产免费男女视频| 欧美一区二区精品小视频在线| 99re在线观看精品视频| 久久天堂一区二区三区四区| 欧美日韩乱码在线| 久9热在线精品视频| 亚洲中文日韩欧美视频| 亚洲 国产 在线| 最近视频中文字幕2019在线8| 哪里可以看免费的av片| 亚洲精品美女久久av网站| 欧美成人性av电影在线观看| 欧美日韩福利视频一区二区| 国产精品永久免费网站| 999久久久国产精品视频| 美女免费视频网站| 男女床上黄色一级片免费看| а√天堂www在线а√下载| 欧美乱妇无乱码| 亚洲天堂国产精品一区在线| 一边摸一边做爽爽视频免费| av在线播放免费不卡| 久99久视频精品免费| 欧美精品啪啪一区二区三区| 18禁国产床啪视频网站| 啪啪无遮挡十八禁网站| 99热这里只有精品一区 | aaaaa片日本免费| 欧美日韩瑟瑟在线播放| 免费av毛片视频| 国产欧美日韩一区二区精品| 最近最新中文字幕大全电影3| 香蕉久久夜色| 三级国产精品欧美在线观看 | 日韩精品免费视频一区二区三区| 搡老妇女老女人老熟妇| 婷婷丁香在线五月| 免费一级毛片在线播放高清视频| 日本黄大片高清| 岛国视频午夜一区免费看| 18禁裸乳无遮挡免费网站照片| 一级毛片高清免费大全| 久久欧美精品欧美久久欧美| 久久久久久国产a免费观看| 成人av在线播放网站| 免费观看精品视频网站| 小说图片视频综合网站| 一a级毛片在线观看| 久久中文字幕人妻熟女| 国产成人一区二区三区免费视频网站| 亚洲av中文字字幕乱码综合| 我的老师免费观看完整版| 国产av一区二区精品久久| 欧美日韩福利视频一区二区| 韩国av一区二区三区四区| 免费av毛片视频| 国产亚洲欧美98| 久久国产精品影院| 最近视频中文字幕2019在线8| 桃色一区二区三区在线观看| 欧美 亚洲 国产 日韩一| 国产高清视频在线播放一区| 床上黄色一级片| 国产欧美日韩一区二区精品| 男男h啪啪无遮挡| 又粗又爽又猛毛片免费看| 久久久久久大精品| 欧美丝袜亚洲另类 | 亚洲一区中文字幕在线| 国产不卡一卡二| 禁无遮挡网站| 看免费av毛片| 亚洲国产精品合色在线| 国产私拍福利视频在线观看| 五月玫瑰六月丁香| 操出白浆在线播放| 免费在线观看视频国产中文字幕亚洲| 亚洲美女黄片视频| 人成视频在线观看免费观看| 在线观看日韩欧美| 精品日产1卡2卡| 老汉色∧v一级毛片| 啦啦啦免费观看视频1| 淫秽高清视频在线观看| 久久性视频一级片| 老司机午夜福利在线观看视频| 黄色毛片三级朝国网站| 欧美不卡视频在线免费观看 | 欧美成人一区二区免费高清观看 | 精品日产1卡2卡| av福利片在线观看| 国产免费av片在线观看野外av| 在线观看免费日韩欧美大片| 一级毛片女人18水好多| 国产三级中文精品| 国产亚洲精品久久久久5区| 校园春色视频在线观看| 午夜激情av网站| 1024香蕉在线观看| 一本一本综合久久| 精品国内亚洲2022精品成人| 男人舔女人的私密视频| 九九热线精品视视频播放| 免费看日本二区| 99热这里只有是精品50| 国产一区二区在线观看日韩 | 正在播放国产对白刺激| 国产爱豆传媒在线观看 | 一本精品99久久精品77| 亚洲熟女毛片儿| 久久天堂一区二区三区四区| 久久久久九九精品影院| 成人18禁在线播放| 黄色成人免费大全| 亚洲美女黄片视频| 国产精品一区二区三区四区久久| 日韩大码丰满熟妇| 非洲黑人性xxxx精品又粗又长| 亚洲成av人片在线播放无| 国产三级在线视频| 亚洲欧美一区二区三区黑人| aaaaa片日本免费| 一本大道久久a久久精品| 国产成人系列免费观看| 国产成人影院久久av| 一本精品99久久精品77| 亚洲成人免费电影在线观看| 国产精品日韩av在线免费观看| 日韩有码中文字幕| 可以在线观看毛片的网站| 日韩成人在线观看一区二区三区| 国产精品 国内视频| 午夜福利成人在线免费观看| 一级黄色大片毛片| 国产高清视频在线观看网站| 精品一区二区三区四区五区乱码| 欧美乱妇无乱码| 黄色毛片三级朝国网站| 国产成人系列免费观看| 桃红色精品国产亚洲av| 可以在线观看毛片的网站| 午夜福利18| or卡值多少钱| www国产在线视频色| av免费在线观看网站| 深夜精品福利| 午夜激情福利司机影院| 男男h啪啪无遮挡| 一区福利在线观看| 欧美人与性动交α欧美精品济南到| 欧美日本视频| 亚洲美女视频黄频| 99精品久久久久人妻精品| 日韩国内少妇激情av| 久久天堂一区二区三区四区| 国产成人aa在线观看| 9191精品国产免费久久| 国产在线观看jvid| 高清毛片免费观看视频网站| 一区二区三区国产精品乱码| 亚洲精品久久成人aⅴ小说| 黄色片一级片一级黄色片| 国产伦一二天堂av在线观看| 天堂√8在线中文| 国产高清videossex| 麻豆久久精品国产亚洲av| 久久精品国产亚洲av高清一级| 亚洲av中文字字幕乱码综合| 一级a爱片免费观看的视频| aaaaa片日本免费| 免费在线观看影片大全网站| www日本黄色视频网| 久久久久久久精品吃奶| 亚洲精品国产一区二区精华液| 亚洲一区中文字幕在线| 五月伊人婷婷丁香| 久久精品国产亚洲av高清一级| 午夜福利成人在线免费观看| 亚洲av五月六月丁香网| 1024香蕉在线观看| 日本一二三区视频观看| 久久久久久久久免费视频了| 欧美日韩黄片免| 中文字幕人成人乱码亚洲影| 老鸭窝网址在线观看| 女人爽到高潮嗷嗷叫在线视频| 久久精品夜夜夜夜夜久久蜜豆 | 日本撒尿小便嘘嘘汇集6| 国产精品免费视频内射| 90打野战视频偷拍视频| 亚洲真实伦在线观看| 一区福利在线观看| 欧美日韩一级在线毛片| 国产精品一区二区精品视频观看| 90打野战视频偷拍视频| 色av中文字幕| 日本免费一区二区三区高清不卡| 成人手机av| 亚洲欧美日韩东京热| 91av网站免费观看| 成人精品一区二区免费| 国产精品av视频在线免费观看| 国产真实乱freesex| 欧美日韩瑟瑟在线播放| 九色成人免费人妻av| 成年女人毛片免费观看观看9| 999久久久精品免费观看国产| 男女之事视频高清在线观看| 久久久精品大字幕| www日本黄色视频网| 欧美日韩福利视频一区二区| 变态另类成人亚洲欧美熟女| 久久久国产精品麻豆| 日本三级黄在线观看| 老熟妇仑乱视频hdxx| 欧美zozozo另类| 亚洲av成人精品一区久久| 亚洲欧美日韩无卡精品| 久99久视频精品免费| 成人国产综合亚洲| a级毛片a级免费在线| 伦理电影免费视频| 日韩成人在线观看一区二区三区| 欧美日韩一级在线毛片| 精品不卡国产一区二区三区| 狠狠狠狠99中文字幕| 韩国av一区二区三区四区| 99热只有精品国产| 日韩欧美在线二视频| 亚洲欧美日韩无卡精品| 99久久国产精品久久久| 欧美日韩黄片免| 色精品久久人妻99蜜桃| 国产成+人综合+亚洲专区| 亚洲性夜色夜夜综合| 国产精品电影一区二区三区| 久久精品国产清高在天天线| av片东京热男人的天堂| 国产一级毛片七仙女欲春2| 一夜夜www| 免费一级毛片在线播放高清视频| 99热只有精品国产| www国产在线视频色| 国产精品影院久久| 久9热在线精品视频| 黑人巨大精品欧美一区二区mp4| 日本a在线网址| 中文字幕av在线有码专区| 免费电影在线观看免费观看| 久久久久国产一级毛片高清牌| 此物有八面人人有两片| 最近在线观看免费完整版| 欧美成人午夜精品| 人成视频在线观看免费观看| 特级一级黄色大片| 丝袜美腿诱惑在线| 成人精品一区二区免费| 国产欧美日韩精品亚洲av| 99热这里只有是精品50| 精品国产美女av久久久久小说| 欧美极品一区二区三区四区| 人人妻,人人澡人人爽秒播| 99精品久久久久人妻精品| 妹子高潮喷水视频| 高清毛片免费观看视频网站| 婷婷精品国产亚洲av| 久久精品国产亚洲av高清一级| 搡老熟女国产l中国老女人| or卡值多少钱| 欧美一级a爱片免费观看看 | 一级片免费观看大全| 精品高清国产在线一区| 国产高清激情床上av| 中文字幕精品亚洲无线码一区| 国产精品一区二区精品视频观看| 国产亚洲精品久久久久5区| 亚洲欧美日韩高清在线视频| 日韩 欧美 亚洲 中文字幕| 可以在线观看的亚洲视频| 中国美女看黄片| 欧美大码av| 欧美在线黄色| 午夜激情福利司机影院| 精品国产超薄肉色丝袜足j| 亚洲七黄色美女视频| 久久精品亚洲精品国产色婷小说| 久久中文字幕一级| √禁漫天堂资源中文www| 精品久久久久久,| 可以免费在线观看a视频的电影网站| 亚洲av成人不卡在线观看播放网| 香蕉国产在线看| 欧美三级亚洲精品| 久久精品91无色码中文字幕| 757午夜福利合集在线观看| 在线观看美女被高潮喷水网站 | 午夜老司机福利片| 国产爱豆传媒在线观看 | 亚洲成人免费电影在线观看| 国产精品久久久久久人妻精品电影| 搡老熟女国产l中国老女人| 欧美一区二区国产精品久久精品 | 午夜两性在线视频| 少妇裸体淫交视频免费看高清 | 日韩精品中文字幕看吧| 欧美日韩乱码在线| 无限看片的www在线观看| 久久中文字幕人妻熟女| netflix在线观看网站| 淫秽高清视频在线观看| 看片在线看免费视频| 老汉色av国产亚洲站长工具| 男女那种视频在线观看| 美女黄网站色视频| 午夜久久久久精精品| 日韩欧美三级三区| 久久久久久久久免费视频了| 88av欧美| 看免费av毛片| 亚洲精品国产精品久久久不卡| 黄色毛片三级朝国网站| 亚洲av日韩精品久久久久久密| 一级毛片高清免费大全| 国产亚洲欧美在线一区二区| 国产精品野战在线观看| 国产黄a三级三级三级人| 国内精品久久久久精免费| 日韩欧美三级三区| 久久国产精品人妻蜜桃| 亚洲av美国av| 精品国产乱子伦一区二区三区| 一二三四社区在线视频社区8| 最近最新中文字幕大全电影3| 亚洲,欧美精品.| 精品国产乱子伦一区二区三区| 国产高清视频在线观看网站| 日本一本二区三区精品| 深夜精品福利| 亚洲午夜理论影院| 久久天躁狠狠躁夜夜2o2o| 国内少妇人妻偷人精品xxx网站 | 可以免费在线观看a视频的电影网站| 久久精品aⅴ一区二区三区四区| 久久热在线av| 国产亚洲欧美在线一区二区| 女人爽到高潮嗷嗷叫在线视频| 日韩av在线大香蕉| 妹子高潮喷水视频| 久久久久性生活片| 亚洲片人在线观看| 亚洲在线自拍视频| 精品久久久久久久毛片微露脸| 国内精品一区二区在线观看| 久久久久国内视频| 一进一出抽搐gif免费好疼| 日本撒尿小便嘘嘘汇集6|