• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Investigation of electron cyclotron wave absorption and current drive in CFETR hybrid scenario plasmas

    2023-10-08 08:20:36HanlinWANG王瀚林XiaojieWANG王曉潔ChaoZHANG張超YunyingTANG湯允迎andFukunLIU劉甫坤
    Plasma Science and Technology 2023年9期
    關(guān)鍵詞:張超

    Hanlin WANG(王瀚林),Xiaojie WANG(王曉潔),Chao ZHANG(張超),Yunying TANG(湯允迎) and Fukun LIU(劉甫坤)

    1 Institute of Plasma Physics,Chinese Academy of Sciences,Hefei 230031,People’s Republic of China

    2 University of Science and Technology of China,Hefei 230026,People’s Republic of China

    Abstract The investigation of electron cyclotron(EC) wave absorption and current drive has been performed for the China Fusion Engineering Test Reactor(CFETR) hybrid scenarios using the TORAY code.To achieve the physics goal of the EC system in CFETR,a total of four wave frequency values and nine locations of launching antennas have been considered,and the injection poloidal and toroidal angles have been scanned systematically.The electron cyclotron current drive(ECCD)efficiency of the 170 GHz EC system is quite low due to the wave-particle interactions being located at the low-field side.To optimize the ECCD efficiency,the wave frequency is increased up to 221-250 GHz,which leads to the power being deposited at the high-field side.The off-axis ECCD efficiency can be significantly enhanced by launching EC waves from the top window and injecting them towards the high-field side.The optimized ECCD efficiency at ρ=0.32 and at ρ=0.4 is 2.9 and 2.2 times that of 170 GHz,respectively.

    Keywords: current drive,ECCD efficiency,CFETR

    1.Introduction

    The China Fusion Engineering Test Reactor(CFETR) is a next generation device in the roadmap of China’s magnetic confinement fusion energy development,which is targeted at bridging the gap between ITER and the first commercial fusion power plant [1].In the early conceptual design of CFETR,the device parameters wereR/a=5.7/1.6 andB0=5 T(named phase I in the literature) [2].In the latest design,to achieve long-pulse operation with GW-level fusion power,the size and magnetic field of the device have been increased and set atR/a=7.2/2.2 andB0=6.5 T,respectively,and a hybrid scenario has been developed using integrated simulations [3].Compared to steady-state operation,hybrid operation has higher internal inductance and plasma currents as well as lowerβNand Greenwald density.

    Electron cyclotron resonance heating(ECRH) [4-7] and electron cyclotron current drive(ECCD) [8-11] are the two effects produced by the interaction between electromagnetic waves in the electron cyclotron(EC) frequency or its low harmonics with plasma.EC systems possess a number of attractive technological features.First,since electron cyclotron waves(ECWs) propagate in a vacuum,the EC launcher can be placed distant from the plasma.Second,the power deposition can be flexibly controlled by the toroidal magnetic field,wave frequency and antenna steering angle.Third,the physics mechanism by which ECW interacts with plasma is simple,and the coupling is insensitive to the conditions at the plasma boundary.Fourth,the interaction of ECW with the plasma edge is negligible,so there is no additional impurity release.Furthermore,a reliable high-power source can be obtained.

    ECRH/ECCD is a well-established and widely used scheme for plasma localized heating and non-inductivecurrent drive in tokamak fusion reactors.It can be used for start-up assistance,plasma heating,off-axis current drive and magnetohydrodynamic(MHD) instability suppression.In 2015,the conceptual design of an EC system on a small CFETR was proposed,and a 20 MW 170 GHz EC launcher was designed to be installed on the equatorial window[12].In 2018,the performance of ECRH/ECCD at three EC antenna positions(top,low-field side(LFS) and mid-plane launcher)in the flattop and ramp-up phase was studied in the steadystate operation of CFETR phase I [13].In 2019,the ECCD characteristics of equatorial and top port launchers in CFETR phase I plasma with a flat density profile were evaluated,and the current drive for the equatorial port launcher at different wave frequencies was simulated in a relatively low electron temperature plasma of CFETR phase II [14].After iterative design between physics and engineering research,CFETR hybrid scenario was proposed [3].The main task of the EC system was identified as the application of off-axis heating and current drives(H&CD) to improve confinement and MHD performance.Based on to the physical integrated simulation of the CFETR baseline hybrid scenario,the EC system was designed to drive 800 kA and 460 kA current at normalized plasma radiusρ=0.32 andρ=0.4,respectively,to provide modification of theqprofile,and to apply 130 kA drive current for neoclassical tearing mode(NTM)suppression nearq=2(ρ=0.51).

    In the engineering design,36 MW EC power needs to be injected into the plasma through three top launchers[15],and 18 transmission lines and a pair of focusing mirrors and steering mirrors needs to be installed in the pipeline of two of the three top windows.In addition,shielding blocks are required inside the pipeline to protect the components from neutron irradiation [16].It is a huge challenge for the EC system design to achieve high-power injection in a limited space.On the other hand,the CFETR blanket is penetrated by the EC system and the tritium breeding ratio(TBR) is hence reduced.In order to make sure that TBR>1.1 and achieve tritium self-sufficiency,the port size needs to be minimized.

    In order to meet the above requirements and constraints,the performance of ECW absorption and current drive in CFETR hybrid scenario plasmas is investigated in this study,and the balance between ECCD efficiency and engineering feasibility is considered.The paper is organized as follows.Section 2 describes the main parameters of CFETR hybrid plasma and the setup of the EC system.The simulation results and discussion of ECCD performance at 170 GHz are presented in section 3.The optimization of current drive by depositing ECW at the high-field side(HFS) is addressed in section 4.Finally,a conclusion is given in section 5.

    2.EC interactions in CFETR hybrid scenario plasma

    2.1.CFETR hybrid scenario

    In the analysis presented in this paper,the CFETR baseline hybrid scenario [3] has been considered.The main plasma parameters are as follows: major radiusR0=7.2 m,minor radiusa=2.2 m,plasma currentIP=13 MA and the vacuum toroidal magnetic field in the center isB0=6.5 T.The equilibrium of the CFETR hybrid scenario is constructed as per an EFIT code [17].All simulations are based on the electron density and temperature profiles of the CFETR hybrid baseline scenario,as shown in figure 1.The central electron densityne0=1.28×1020m-3,the central electron temperatureTe0=30.48 keV and the effective charge numberZeff≈2.5.Here,ρis the normalized plasma radius,which is the square root of the normalized toroidal magnetic flux.

    Figure 1.Electron density(blue)and temperature(red)profiles of the CFETR baseline hybrid scenario.

    2.2.EC resonances in CFETR

    In this paper,the following four wave frequencies are investigated,namelyf=170,210,221 and 250 GHz.The relationship between wave frequency and toroidal magnetic field satisfies

    wherefis the ECW frequency,nis the electron harmonic number andBtis the magnetic field of EC resonance.According to equation(1),the fundamental harmonic ordinary mode(O1-mode) is mainly considered in this study.

    The major radius of EC cold resonance is located atRce=28nR0(m)B0(T)/f(GHz).It can be observed that the radial region where the ECW interacts with the plasma is related to the ECW frequency and the magnetic field.Figure 2 provides a clear view of the relationship betweenRcewithB0for the four frequency values,and for the first and second harmonics.Here,the O2-mode refers to the second harmonic ordinary mode.In general,plasmas interact with ECW in EC frequency or its low harmonics,and the EC power may be absorbed before reaching the cold resonance in the case of LFS injection,especially in high electron temperatures plasmas.SinceB0is set at 6.5 T,the following conclusion can be reached.For 170 GHz,the first harmonic interaction occurs at the LFS,thus resulting in a lower ECCD efficiency due to trapped particle effects.For 210,221 and 250 GHz,theinteraction of the first harmonic occurs at the HFS,and the ECW can drive significantly higher currents at off-axis locations as a result of fewer collisions and trapped electrons.

    Figure 2.Magnetic field B0 versus the major radius of EC cold resonance Rce for ECW frequencies f=170,210,221 and 250 GHz.Horizontal black dashed line denotes the radius of vessel center R0=7.2 m.Upper and lower horizontal blue dashed lines are the radii locations of the last closed flux surface for the LFS and HFS,respectively.

    Figure 3.Definitions of poloidal angle(left) and toroidal angle(right) of ECW.Red solid lines correspond to the CRL,the pink dashed lines to the ECW incident path and the blue dashed line to the magnetic axis.Contour lines in the left diagram are the plasma equilibrium shape,the blue solid lines in the right diagram are the last closed flux surface.Red solid semi-circle is the position of the launching point.

    Figure 4.Candidate launching points and frequencies studied in CFETR hybrid scenario plasmas.Inner vertical lines denote the first harmonic CRL for ECW frequencies of 170(red),210(green),221(yellow) and 250 GHz(magenta).Contour lines are the magnetic equilibrium for CFETR hybrid scenario plasmas.

    Figure 5.EC-driven current(color scale)and the radial location of current density peak(blue contour lines)as a function of the poloidal angle and toroidal angle,for f=170 GHz.White dashed line delimits the region in which power absorption is larger than 95%.Figures(a),(b),(c)and(d) refer to the launching points A,B,C and E,respectively.

    Figure 6.Maximum EC-driven current per unit power versus normalized radius ρ for the candidate launching points,obtained by means of a scan of the poloidal and toroidal angles,for power absorption larger than 95%.Figures(a),(b),(c) and(d) refer to the results of ECW frequencies of 170,210,221 and 250 GHz,respectively.

    Although the cold resonance layer(CRL) of the second harmonic forf=250 GHz is located outside the plasma(R=10.48 m),the second harmonic absorption may occur in the plasma and affect the ECCD efficiency due to the downshift resonance absorption effect [18] in the high electron temperature of CFETR hybrid scenarios.Therefore, ordinary mode absorption at the second harmonic might also be considered at high wave frequencies.The cut-off density is about 3.6×1020m-3for 170 GHz,and the other three frequencies have higher cut-off density.Hence,the refraction effect does not play a major role except at large incident angle near the plasma boundary.

    The ray tracing code TORAY [19] is used to carry out the calculations of ECRH/ECCD performance in this study.TORAY code is a quasi-optical ray tracing code for EC Gaussian beam propagation.The power absorption is computed by solving the dispersion relation of ECW including momentum conservation in electron-electron collisions,while the current drive is computed by the adjoint approach reworked by Lin-Liu [20].The TORAY code has been successively benchmarked with other EC codes for ECCD in ITER [21].

    2.3.EC system setup

    The EC system consists of RF sources,transmission lines,EC launchers and auxiliary subsystems,such as high-voltage power supply and water cooling.The microwave source consists of at least 36 gyrotrons each with 1 MW output power.Each EC launcher mainly consists of a pair of focusing mirrors and steering mirrors.The launcher can change the location of EC power deposition by adjusting the incident angles of the steering mirror to achieve the desired physical objectives at different magnetic surfaces.The definitions of ECW incident angles are shown as figure 3.The poloidal angleθis the angle between the vertical positive direction and EC rays,and the toroidal angle φ is the angle between the major radius positive direction and EC rays.It should be noted that φ=180°corresponds to the case where EC wave injection is perpendicular to the magnetic field,and in this case,there is no ECCD [18,22].The poloidal angleθand toroidal angle φ are in units of degree.In the engineering design,two EC launchers are designed for off-axis ECCD and one EC launcher for NTM control.

    In consideration of TBR requirements and engineering constraints,five launching points(A-E) are selected for simulations of 170 GHz ECW,as shown in figure 4,where launching point E is located in the equatorial window and launching points A-D are located in the top window.In addition,four launching points in the top window(F-I) are considered for ECCD simulation at higher ECW frequencies.The locations of these candidate launching points are listed in table 1.

    3.ECCD at 170 GHz

    The investigation of EC power deposition and current drive performance requires a wide scan among ECW frequency,launching position,poloidal angle and toroidal angle.Based on the technical availability of the gyrotron,the frequency chosen for simulation in this section is 170 GHz.Numerical simulations have been carried out by scanning the injection angles for launching positions A-E atf=170 GHz.The ECdriven current per unit power is shown in figure 5 as a function of the injection angles,together with the contours ofthe radial location of the current density peak for the launching points A,B,C and E.The ECCD performance of launching points C and D is similar.Hence,the result for launching point D is not presented in figure 5.The region under the white dashed line indicates that the power absorption is larger than 95%.

    Table 1.Locations of candidate launching points.

    According to the results in figure 5,it is possible to maximize the driven current on a specific magnetic surface by selecting the injection angle appropriately.Overall,the maximum ECCD for launching points A and B are located in the far off-axis,while the maximum ECCD for launching points C and E are located in the middle radius.The ECW launched from launching points C and E allow a larger range of power deposition locations,and the driven current decreases as the deposition location changes from middle off-axis to the plasma center.For the launching point A,it is hard to drive current near the magnetic axis.

    The results of the driven current and corresponding power absorption for various radial locations are listed in table 2.IEC/PECis the total driven current per unit power in units of kA/MW,γECis the ECCD efficiency in 1020A/(m2W),Pabsis the power absorption coefficient in W/W,jEC/PECis the drive current density per unit power in kA/(m2MW),and Δρis the half-profile width at 1/e of the current density peak.The widely used definition of ECCD efficiency in the literature is,

    whereneis the electron density andPECis the incident power of ECW.The maximization ofγECis the ultimate goal of the current drive system in a reactor.

    TheIEC/PECin row 2 is the maximum current obtained by scanning the toroidal and poloidal angles of each launching point.The values in rows 3-6 are the ECCD efficiency,injection angles,radial location of current density peak and power absorption coefficient corresponding to row 2,respectively.The values ofIEC/PECmaxima for points C and D are approximate,as are the deposition locationρa(bǔ)nd the power absorption coefficientPabs.This is due to the fact that the launching points C and D are geometrically almost in a straight line with respect to the magnetic axis.It can be observed that the maximum currents for the five launching points are located in the far off-axis.One reason is that the CRL of 170 GHz is located at the LFS,as can be seen in figure 2.Another reason is that the deposition location is moved more outwards due to the Doppler shifted effect caused by the large toroidal angle.

    The driven currents in rows 8 and 14 are the maximum currents nearρ=0.32 andρ=0.4,respectively,which are selected by scanning the injection angles.The values in rows 9-12 and 15-18 are the ECCD efficiency,injection angles,drive current density and power absorption coefficient corresponding to the maximum currents,respectively.It is found that the launching point C(atθ=132°and φ=209°)and D(atθ=133° and φ=218°) are the optimal settings for ECCD atρ=0.32 andρ=0.4,respectively.In addition,the ECCD efficiencies atρ=0.32 for launching points C,D and E are approximate,and the ECCD efficiencies atρ=0.4 for launching points C and D are approximate.

    To meet the requirement of NTM control,the maximum driven current(in row 21) with the current density peak located atρ=0.51 and profile width Δρ≤0.05 is selected by scanning the ECW injection angles.Here,the profile width Δρ≤0.05 is chosen based on the simulations of NTM evolution studied by the MHD task force.As the deposition width increases,the current required to stabilize the magnetic island increases.However,the EC power available for NTM control is limited.The values in rows 22-26 are the ECCD efficiency,injection angles,drive current density and power absorption coefficient corresponding to row 21,respectively.Note that the minimized profile widths in row 20 of launching points A and B are larger than 0.05,which indicates that these two launching points are not suitable for NTM control whenthe wave frequency is 170 GHz.The maximum currents for launching points C and D are approximate.Based on the above results,point C is selected as the launching point for ECCD and NTM control of the 170 GHz EC system,considering the engineering accessibility and the functional expansion of core heating.

    4.ECCD at higher frequency

    The ECCD efficiency of the CFETR hybrid scenario at 170 GHz is quite low.The main reason is that the interaction occurs in the LFS,where the impact of trapped particles is large.To optimize the ECCD efficiency,the EC interaction should occur at the HFS by increasing the wave frequency,as mentioned in section 2.2.Therefore,the power absorption and current drive performance have been evaluated by scanning injection angles and launching positions for 210,221 and 250 GHz,respectively.Each case yields a result,as shown in figure 5,hence there are a large number of figures.To get a clear view of the ECCD performance from these results,the driven current per unit powerIEC/PECobtained by scanning the whole range of injection angles under consideration is plotted versus the normalized radiusρ(at the radial location of the current density peak),as shown in figure 6.Each curve represents the maximum current that can be driven at a given normalized radiusρfor a specific frequency and launching point.Note that the maximum current is chosen from the driven current that corresponds to at least 95% power absorption.

    The results of 170 GHz are also plotted in figure 6 for comparison.Forf=170 GHz,the maximum driven current for profile tailoring or NTM stabilization is less than 10 kA MW-1,as discussed in section 3.It can be observed that the driven current is lower at the plasma center than midradius for launching points C,D and E.The ECCD efficiency is usually greater in the core plasma due to the higher temperature and smaller fraction of trapped particles.However,the CRL is located at the off-axis of the LFS,as shown in figure 2.This means that the ECW is difficult to deposit at the plasma center.On the other hand,the deposition radial location increases with the increase of toroidal angle,as shown in figures 5(c) and(d).Hence,the driven current at mid-radius for launching points C,D and E is higher than that at the core,because the current profile of a larger toroidal angle is broadened by the Doppler shift.This behavior is consistent with the studies of ECCD efficiency on JET [23].

    Table 2.Parameters relevant to the different launching points for ECCD applications.

    Forf=210 GHz,the ECCD results of launching points A,C and E are presented in figure 6(b).The launching points F-I are located too close to the CRL,which results in lower ECCD efficiency than that of launching point A for the plasma region of interest.The radial region that is available for ECCD is clearly visible in the plot.The lower limit is close to the plasma center in all the cases,while the upper limit of launching point C is close toρ=0.7,and those of the others are more outwards.In the radial range ofρ<0.2,the maximum driven current can be reached by means of a suitable choice of the injection angles for launching from the mid-plane.At the radial location close toρ=0.3,the launching point C is the optimized choice for ECCD among the candidate launching points.In the plasma region ofρ>0.45,the launching point A is slightly better for driven current.The maximum driven current is 18.56 kA MW-1,close toρ=0.32 and 16.35 kA MW-1close toρ=0.4,as listed in table 3.For NTM control,after selecting the results that satisfy the requirement of profile width Δρ≤0.05,the maximum current is 11.22 kA MW-1,close toρ=0.51.The driven current in the plasma core is slightly lower than offaxis for launching points C and E.The CRL off=210 GHz is located at the mid-radius of the HFS.The EC waves deposited at the HFS can interact with higher-energy electrons,the low collision rate results in higher ECCD efficiency nearρ=0.3.In addition,it is found that launching point A has a significant minimum value atρ=0.38,but is close to the peak value atρ=0.42.The reasons are as follows.The maximum current atρ=0.38 is 8.7 kA MW-1,which is obtained by aiming atθ=152°and φ=212°.However,the maximum current atρ=0.42 is reached by setting the injection angle close toθ=144° and φ=238°.Even the radial position ofρ=0.38 is close toρ=0.42.However,the toroidal angles of these two situations are quite different.In general,a larger toroidal angle results in higher ECCD efficiency due to the current profile being broadened by the Doppler shift.The reason is essentially that the deposition location is sensitive to the injection angle when the top launching point is close to the CRL.The same behavior can be found in the case of launching points A and I atf=221 GHz,which is due to the same reason.

    Forf=221 GHz,almost all the radial range is covered for ECW launched from points B,C and E,while the radial range of launching point I is 0.18≤ρ≤0.97.In the radial range ofρ<0.2,the maximum current is driven by launching from the mid-plane.In the radial range of 0.2<ρ≤0.3,launching point C is able to provide a larger driven current.Point B is the optimal launching position for ECCD in the range of 0.34≤ρ<0.45.The ECW launched from the top is good at driven current in the region ofρ≥0.45.It can be observed that,as the envelope of the maximum current moves from plasma core to the edge,the launching point corresponding to the maximum current moves from mid-plane to the top.The maximum driven current is 20.07 kA MW-1close toρ=0.32 and 19.27 kA MW-1close toρ=0.4.For NTM control,the maximum current is 15.21 kA MW-1close toρ=0.51.

    Forf=250 GHz,the driven current is plotted versus the normalized radiusρfor seven launching point positions.Overall,the EC waves launched from the LFS or mid-plane isgood at driving current near the magnetic axis,while the ECW launched from the top is good for tailoring the current profiles and active control of NTM.Note that the current in the range of 0.4<ρ<0.7 driven by ECW launched from the top is about 1.3 times that of the mid-plane.This is because the ECW is partially absorbed by the second harmonic interaction at the LFS before it reached the CRL of the first harmonic when EC power is launched from the midplane.The maximum driven current is 21.04 kA MW-1close toρ=0.32 and 18.32 kA MW-1close toρ=0.4.For NTM control,the maximum current is 14.65 kA MW-1close toρ=0.51.For launching points C and E,the current is higher at the core.One reason is the higher temperature and fewer trapped particles in the plasma center.Another reason is that the second harmonic absorption occurs in the LFS,which reduces the EC power available for the fundamental harmonic,when the wave is incident from launching points C or E.For the case of launching point E,the maximum currents atρ=0.44,0.45 and 0.46 are 13.71,4.25 and 13.18 kA MW-1,respectively.The driven current atρ=0.45 is much smaller than the adjacent values.The reason is that the maximum driven current atρ=0.45 is reached by settingθ=70° and φ=204°,which is far away from the region of the maximum driven current atρ=0.44(θ=89°and φ=205°)and 0.46(θ=88° and φ=204°).This is because the value of the deposition location of the region close toθ=88° and φ=204° is not continual after the rounding-off method.

    The maximum ECCD efficiency as a function of the ECW frequency for different launching points is shown in figure 7 for the radial positions atρ=0.32 andρ=0.4.Note that the top launching point A is too close to the CRL off=170 GHz,and the low-power absorption coefficient(less than 65%) in the radial range ofρ=0.32-0.51 is one of the reasons for the low ECCD efficiency.Similarly,the ECCD efficiency of launching point B at 170 GHz and launching point F at 250 GHz is slightly lower relative to the other launching points.

    Figure 7 provides the following information.(1)Overall,the ECCD efficiency exhibits a saturation setting in a wave frequency of 221-250 GHz.(2) The maximum ECCD efficiency atρ=0.32 is reached by launching ECW of 250 GHz from point A,which is almost 2.9 times the maximum of 170 GHz.(3) The maximum current atρ=0.4 is driven by launching ECW of 221 GHz from point B,which is about 2.2 times the maximum of 170 GHz.(4) When the wave frequency is 250 GHz,the ECCD efficiencies for toplaunching points A and I are slightly higher than those of the LFS outside launching point C and mid-plane launching point E.This is because the second harmonic absorption at the LFS reduces the EC power available for the fundamental harmonic when the wave is incident from launching points C or E.(5)The maximum ECCD efficiency atρ=0.32 forf=221 GHz is 0.185,which is close to the maximum ECCD efficiencyγEC=0.194 forf=250 GHz.This means that 221 GHz provides a compromise to achieve higher ECCD efficiency by using a lower frequency.

    Figure 7.Wave frequency f versus the maximum ECCD efficiency of the candidate launching points.Figures(a) and(b) refer to the radial positions ρ=0.32 and ρ=0.4,respectively.

    Figure 8.ECW frequency versus EC-driven current,obtained by selecting the maximum current among the cases that satisfy the requirement of NTM control for the candidates’ launching points.

    Table 3.Parameters relevant to the different launching points for ECCD applications.

    To minimize the window size of the tritium breeding blanket penetrated by the EC system means that the toroidal angle is as small as possible.From the injection angles of row 5 and row 11 in table 3,the toroidal angles corresponding to the top launching points A,B and H are relatively larger(φ>235°).Considering the balance between ECCD efficiency,engineering achievability and TBR requirements,the 221 GHz ECW launched from point E is preferable for off-axis current drive in CFETR hybrid scenario plasmas.

    The maximum NTM control current for the candidates’launching points is a function of ECW frequency,as shown in figure 8.In the results carried out by scanning the injection angles,the half-profile widths of launching points B,C,D and E are larger than 0.05 atf=250 GHz.This means that these launching points do not meet the requirements of NMT control at any injection angles.Similarly,launching points A and B are not able to stabilize the NTM,whenf=170 GHz.

    From figure 8,the following general conclusion can be drawn.(1) The maximum current for NTM control is driven by injecting ECW of 221 GHz from point B.The current of 15.21 kA MW-1is driven by aiming the injection angle toθ=132°and φ=218°,as listed in column 5 and row 18 oftable 3.(2) Forf=250 GHz,only the top launching points(A and F-I) appear in the figure.This is because the deposition widths of the mid-plane launching point E and the outside launching point C cannot meet the requirement of NTM control.(3) The maximum NTM control current of launching point C forf=221 GHz is 15.01 kA MW-1.It is close to that of launching point B,but with a lower toroidal angle φ=203°(the corresponding poloidal angleθ=107°).Therefore,to maximize the driven current under engineering restrictions,the 221 GHz ECW launched from point C is the optimal design for NTM control in CFETR hybrid scenario plasmas.

    5.Conclusion

    To achieve the hybrid operating scenario of CFETR,the EC system needs to meet the physical goal of off-axis current drive.To provide a theoretical basis for the design of the EC antenna system,ECW absorption and current drive performance has been evaluated in CFETR hybrid scenario plasmas.A total of four wave frequency values(170,210,221 and 250 GHz) and nine launching points(include the equatorial and top window) have been considered.To cover the whole radial region,the injection poloidal and toroidal angles have been scanned systematically.

    For a 170 GHz EC system,launching point C is chosen for off-axis ECCD and NTM control,and this design takes core heating into account as well.To optimize the ECCD efficiency,the wave frequency is increased up to 221-250 GHz.It is found that the off-axis ECCD efficiency can be significantly enhanced by launching high-frequency ECW from the top window and injecting it towards the HFS.The optimized ECCD efficiencies atρ=0.32 and atρ=0.4 are 2.9 and 2.2 times that of 170 GHz,respectively.

    Considering the maximization of driven current and TBR,the optimal EC antenna design scheme is as follows:select the launching point E with 221 GHz ECW for off-axis current drive; inject 221 GHz ECW into the plasma from launching point C for NTM control.However,since the technique for high-frequency gyrotrons still needs to be developed,the frequency of the EC system concept design is chosen to be 170 GHz.Since the low ECCD efficiency of 170 GHz atB0=6.5 T,decreasing the toroidal magnetic field may be a potential strategy.The same ECCD efficiency can still be obtained at 170 GHz,with the same plasma equilibrium andqprofile except that theB0is reduced to(170/221)×6.5 T=5 T.

    Acknowledgments

    The authors gratefully acknowledge the work of the TORAY development teams,and Hanlin Wang thanks Dr Jiale Chen and Xiaojing Wang for fruitful discussions about the physics targets of the EC system.This study is supported by the National Key R&D Program of China(Nos.2017YFE0300500 and 2017YFE0300503) and the Comprehensive Research Facility for Fusion Technology Program of China(No.2018-000052-73-01-001228).

    猜你喜歡
    張超
    張超,《平安夜》,不銹鋼,高310cm,2023
    張超個人簡介
    散文百家(2021年11期)2021-11-12 03:06:38
    My New Invention
    How to Protect Us from Infectious Diseases
    張超個人簡介
    散文百家(2021年4期)2021-04-30 03:15:20
    張超個人簡介
    散文百家(2021年2期)2021-04-03 14:08:22
    BOUNDEDNESS OF VARIATION OPERATORS ASSOCIATED WITH THE HEAT SEMIGROUP GENERATED BY HIGH ORDER SCHRDINGER TYPE OPERATORS?
    張超攝影展
    攝影與攝像(2020年7期)2020-09-10 07:22:44
    張超作品
    創(chuàng)意立體燈籠賀卡
    亚洲精品国产一区二区精华液| 黑人巨大精品欧美一区二区mp4| aaaaa片日本免费| 最近最新免费中文字幕在线| 丁香欧美五月| 99精品欧美一区二区三区四区| 岛国在线观看网站| 9色porny在线观看| 亚洲成a人片在线一区二区| 长腿黑丝高跟| 亚洲自拍偷在线| 日本黄色视频三级网站网址| 精品国内亚洲2022精品成人| 国产麻豆成人av免费视频| 露出奶头的视频| 国产真人三级小视频在线观看| 老熟妇乱子伦视频在线观看| 日本在线视频免费播放| www.www免费av| 亚洲熟妇熟女久久| 嫩草影视91久久| 搞女人的毛片| 黄片播放在线免费| 欧美一级毛片孕妇| 麻豆国产av国片精品| 久久香蕉精品热| 久久人人97超碰香蕉20202| 男男h啪啪无遮挡| e午夜精品久久久久久久| 99riav亚洲国产免费| 成在线人永久免费视频| 亚洲自拍偷在线| 亚洲国产高清在线一区二区三 | 妹子高潮喷水视频| 国产精品99久久99久久久不卡| e午夜精品久久久久久久| 操美女的视频在线观看| 国产精品秋霞免费鲁丝片| www.www免费av| 国产高清有码在线观看视频 | 欧美在线一区亚洲| 亚洲狠狠婷婷综合久久图片| av天堂在线播放| 激情在线观看视频在线高清| 亚洲国产日韩欧美精品在线观看 | √禁漫天堂资源中文www| 18美女黄网站色大片免费观看| 久久精品国产亚洲av高清一级| 久久精品影院6| 国产蜜桃级精品一区二区三区| 亚洲欧美日韩无卡精品| 手机成人av网站| 欧美中文综合在线视频| 一本久久中文字幕| 欧美黑人欧美精品刺激| 欧美+亚洲+日韩+国产| 国产片内射在线| 亚洲av日韩精品久久久久久密| 国产主播在线观看一区二区| 色在线成人网| 免费看a级黄色片| 国产伦一二天堂av在线观看| 黄片播放在线免费| 亚洲av电影不卡..在线观看| 久久午夜亚洲精品久久| 国产伦人伦偷精品视频| 深夜精品福利| avwww免费| 亚洲第一av免费看| 999久久久国产精品视频| 99国产极品粉嫩在线观看| 变态另类成人亚洲欧美熟女 | 美女午夜性视频免费| 日本五十路高清| 此物有八面人人有两片| 亚洲精品中文字幕在线视频| 在线观看舔阴道视频| 成熟少妇高潮喷水视频| 久久精品国产99精品国产亚洲性色 | 亚洲av片天天在线观看| 91老司机精品| 欧美黄色淫秽网站| 亚洲久久久国产精品| av欧美777| 亚洲全国av大片| 亚洲精品一卡2卡三卡4卡5卡| 亚洲中文日韩欧美视频| 久久人妻av系列| 伦理电影免费视频| 国产成人欧美在线观看| 久久性视频一级片| 久久亚洲真实| 亚洲精品中文字幕一二三四区| 一夜夜www| 丝袜美腿诱惑在线| 久久久久久久午夜电影| 99国产精品免费福利视频| 欧美黑人精品巨大| 午夜福利欧美成人| 中文字幕人成人乱码亚洲影| 国产蜜桃级精品一区二区三区| 国产主播在线观看一区二区| 国产精品久久久av美女十八| 大型黄色视频在线免费观看| 亚洲伊人色综图| 18禁观看日本| 亚洲精品一区av在线观看| 国产av在哪里看| 久久久国产欧美日韩av| 亚洲成人免费电影在线观看| 黄色 视频免费看| 亚洲va日本ⅴa欧美va伊人久久| 日日爽夜夜爽网站| 99国产精品99久久久久| 可以在线观看毛片的网站| 亚洲中文日韩欧美视频| 九色国产91popny在线| 制服诱惑二区| 免费看十八禁软件| 欧美在线一区亚洲| 久久人妻福利社区极品人妻图片| 天堂√8在线中文| 日韩欧美三级三区| 少妇被粗大的猛进出69影院| av欧美777| 日本欧美视频一区| 亚洲欧美日韩无卡精品| 999久久久国产精品视频| 97碰自拍视频| av天堂在线播放| 国产成人系列免费观看| 国产又爽黄色视频| 啦啦啦免费观看视频1| 少妇被粗大的猛进出69影院| 99精品欧美一区二区三区四区| 丰满的人妻完整版| 欧美午夜高清在线| 国产欧美日韩精品亚洲av| 欧美日韩中文字幕国产精品一区二区三区 | 桃色一区二区三区在线观看| 国产精品亚洲av一区麻豆| 色播亚洲综合网| 亚洲七黄色美女视频| av有码第一页| 欧美黑人精品巨大| 亚洲国产看品久久| 国产精品久久久av美女十八| 一进一出好大好爽视频| 在线免费观看的www视频| 久久香蕉国产精品| 成人免费观看视频高清| 亚洲男人天堂网一区| 午夜福利一区二区在线看| 免费看a级黄色片| 伊人久久大香线蕉亚洲五| 午夜视频精品福利| 纯流量卡能插随身wifi吗| 老司机靠b影院| 久久精品91蜜桃| 国产精品亚洲一级av第二区| 97人妻天天添夜夜摸| 色婷婷久久久亚洲欧美| 成人特级黄色片久久久久久久| 美国免费a级毛片| 欧美日韩瑟瑟在线播放| 变态另类成人亚洲欧美熟女 | 男女床上黄色一级片免费看| 99精品欧美一区二区三区四区| 女生性感内裤真人,穿戴方法视频| 亚洲男人天堂网一区| 亚洲熟妇熟女久久| 无遮挡黄片免费观看| 中文字幕人成人乱码亚洲影| 国产蜜桃级精品一区二区三区| 国产男靠女视频免费网站| 午夜精品国产一区二区电影| 波多野结衣av一区二区av| 久99久视频精品免费| 久久这里只有精品19| 欧美人与性动交α欧美精品济南到| 三级毛片av免费| 久久久久精品国产欧美久久久| 久久人人爽av亚洲精品天堂| 夜夜躁狠狠躁天天躁| 老司机深夜福利视频在线观看| 亚洲av片天天在线观看| 亚洲一区中文字幕在线| 日韩免费av在线播放| av在线播放免费不卡| 国产欧美日韩精品亚洲av| 免费在线观看完整版高清| 国产一卡二卡三卡精品| 女性生殖器流出的白浆| 性色av乱码一区二区三区2| 18禁美女被吸乳视频| cao死你这个sao货| 欧美日韩一级在线毛片| 国产极品粉嫩免费观看在线| 午夜成年电影在线免费观看| 精品国产国语对白av| 成年版毛片免费区| 黑人巨大精品欧美一区二区mp4| 免费在线观看日本一区| 人妻久久中文字幕网| 精品欧美一区二区三区在线| bbb黄色大片| 亚洲第一欧美日韩一区二区三区| 欧美一级毛片孕妇| 狂野欧美激情性xxxx| 精品午夜福利视频在线观看一区| 成人国语在线视频| 99精品欧美一区二区三区四区| 91字幕亚洲| 国产欧美日韩一区二区三区在线| 精品电影一区二区在线| 成人国产一区最新在线观看| 91成人精品电影| 亚洲国产看品久久| 十八禁网站免费在线| 亚洲第一青青草原| or卡值多少钱| 丝袜美腿诱惑在线| 日日干狠狠操夜夜爽| 18禁美女被吸乳视频| 免费高清视频大片| 777久久人妻少妇嫩草av网站| 国产伦一二天堂av在线观看| 美女国产高潮福利片在线看| 老司机在亚洲福利影院| 亚洲一区二区三区色噜噜| 精品少妇一区二区三区视频日本电影| 超碰成人久久| 欧美精品啪啪一区二区三区| 久久国产精品影院| 国产99白浆流出| 亚洲欧美激情在线| 丝袜美足系列| 精品久久久久久久久久免费视频| 一级毛片精品| 午夜激情av网站| 不卡一级毛片| 亚洲精品一区av在线观看| 久久久久亚洲av毛片大全| 国产真人三级小视频在线观看| 丰满的人妻完整版| 国产一区二区激情短视频| 欧美日韩亚洲综合一区二区三区_| 女性生殖器流出的白浆| 久久久精品欧美日韩精品| 久久久精品欧美日韩精品| 丝袜美腿诱惑在线| av欧美777| 精品人妻在线不人妻| 国产精品久久久人人做人人爽| 亚洲视频免费观看视频| 亚洲成av片中文字幕在线观看| 男女床上黄色一级片免费看| 免费高清在线观看日韩| 免费搜索国产男女视频| 后天国语完整版免费观看| 免费不卡黄色视频| 精品久久久久久成人av| xxx96com| 国产亚洲精品av在线| 女性被躁到高潮视频| 每晚都被弄得嗷嗷叫到高潮| 色在线成人网| 国产主播在线观看一区二区| 亚洲,欧美精品.| 两个人免费观看高清视频| 国产精品久久久人人做人人爽| 日本精品一区二区三区蜜桃| 欧美激情极品国产一区二区三区| 高清黄色对白视频在线免费看| 桃红色精品国产亚洲av| 一进一出抽搐动态| 欧美乱妇无乱码| 亚洲一卡2卡3卡4卡5卡精品中文| 日韩有码中文字幕| 日本三级黄在线观看| 巨乳人妻的诱惑在线观看| 欧美黑人欧美精品刺激| 亚洲一码二码三码区别大吗| 精品熟女少妇八av免费久了| 亚洲欧美激情综合另类| 亚洲欧洲精品一区二区精品久久久| 久久人妻av系列| 亚洲精品av麻豆狂野| 国产精品国产高清国产av| 老司机在亚洲福利影院| 999久久久精品免费观看国产| 18禁观看日本| 国产在线观看jvid| 亚洲激情在线av| 免费高清视频大片| 90打野战视频偷拍视频| 久久久久国内视频| 少妇裸体淫交视频免费看高清 | 国产精品影院久久| 精品久久久久久,| 欧美日本中文国产一区发布| 亚洲人成77777在线视频| 亚洲av熟女| 亚洲人成伊人成综合网2020| 欧美中文日本在线观看视频| 一区二区三区国产精品乱码| 人人妻,人人澡人人爽秒播| avwww免费| 国产成人精品在线电影| www.www免费av| 国产欧美日韩综合在线一区二区| 欧美一级毛片孕妇| 脱女人内裤的视频| 欧美激情久久久久久爽电影 | 人人妻人人澡欧美一区二区 | 亚洲狠狠婷婷综合久久图片| 国产一区二区三区在线臀色熟女| 在线观看午夜福利视频| 久久精品国产99精品国产亚洲性色 | 伊人久久大香线蕉亚洲五| 天天躁狠狠躁夜夜躁狠狠躁| 99热只有精品国产| 丝袜美腿诱惑在线| 亚洲成国产人片在线观看| 久久伊人香网站| 夜夜躁狠狠躁天天躁| 久久精品国产综合久久久| 亚洲色图av天堂| 日本免费一区二区三区高清不卡 | 老鸭窝网址在线观看| 在线观看日韩欧美| 成熟少妇高潮喷水视频| 精品国产国语对白av| 国产精品98久久久久久宅男小说| 国产精品影院久久| 国产蜜桃级精品一区二区三区| 99在线人妻在线中文字幕| 中国美女看黄片| 国产精品亚洲av一区麻豆| 9色porny在线观看| 精品卡一卡二卡四卡免费| 成人精品一区二区免费| 九色亚洲精品在线播放| 91九色精品人成在线观看| 亚洲国产高清在线一区二区三 | 真人一进一出gif抽搐免费| 欧美中文日本在线观看视频| 黄色a级毛片大全视频| 欧美日韩精品网址| 免费在线观看影片大全网站| 午夜福利,免费看| 免费观看人在逋| 久久香蕉激情| 天堂影院成人在线观看| 欧美国产精品va在线观看不卡| 亚洲精品在线观看二区| 啦啦啦 在线观看视频| 久久精品91无色码中文字幕| 欧美黄色淫秽网站| 久久青草综合色| 精品国产超薄肉色丝袜足j| 最好的美女福利视频网| 国产欧美日韩一区二区三| 久久久久久国产a免费观看| 青草久久国产| 在线观看日韩欧美| 国产精品 欧美亚洲| 99精品在免费线老司机午夜| 国产精品国产高清国产av| 午夜福利高清视频| 一a级毛片在线观看| 久久久久久国产a免费观看| 亚洲一码二码三码区别大吗| 一级作爱视频免费观看| 日本在线视频免费播放| 好看av亚洲va欧美ⅴa在| 老司机靠b影院| 日韩欧美一区视频在线观看| 琪琪午夜伦伦电影理论片6080| 一级,二级,三级黄色视频| 亚洲av电影不卡..在线观看| 好看av亚洲va欧美ⅴa在| 久久久久久人人人人人| 国产高清激情床上av| 男女之事视频高清在线观看| 国产精品美女特级片免费视频播放器 | 成人三级做爰电影| 99久久综合精品五月天人人| 国产激情欧美一区二区| 久久久久久免费高清国产稀缺| 日韩 欧美 亚洲 中文字幕| 国产三级黄色录像| 黄片大片在线免费观看| 校园春色视频在线观看| 国产熟女xx| 久久人人97超碰香蕉20202| 日韩三级视频一区二区三区| 国产精品久久视频播放| 成人三级做爰电影| 国产伦一二天堂av在线观看| 日本免费一区二区三区高清不卡 | 丝袜人妻中文字幕| 成熟少妇高潮喷水视频| 国产亚洲精品av在线| ponron亚洲| 88av欧美| a级毛片在线看网站| 国产人伦9x9x在线观看| 亚洲一区中文字幕在线| 中文字幕人成人乱码亚洲影| 99国产精品一区二区蜜桃av| 女人精品久久久久毛片| 亚洲专区字幕在线| 亚洲精品一区av在线观看| videosex国产| 大香蕉久久成人网| tocl精华| 在线播放国产精品三级| 免费无遮挡裸体视频| 巨乳人妻的诱惑在线观看| 最近最新免费中文字幕在线| 日韩欧美在线二视频| 欧美日韩瑟瑟在线播放| 丁香欧美五月| 极品教师在线免费播放| 99香蕉大伊视频| 国产精品永久免费网站| 亚洲专区国产一区二区| 欧美日韩精品网址| 久热爱精品视频在线9| 午夜福利欧美成人| 91国产中文字幕| 黄片播放在线免费| 一二三四在线观看免费中文在| 国产精品香港三级国产av潘金莲| 青草久久国产| 91大片在线观看| 老司机深夜福利视频在线观看| 午夜免费成人在线视频| 黄色视频,在线免费观看| 欧美中文日本在线观看视频| 久久精品亚洲熟妇少妇任你| 涩涩av久久男人的天堂| 久久人妻福利社区极品人妻图片| 好男人在线观看高清免费视频 | 亚洲专区中文字幕在线| 午夜免费观看网址| or卡值多少钱| 国内精品久久久久久久电影| 男男h啪啪无遮挡| 日韩欧美国产一区二区入口| videosex国产| 久久这里只有精品19| 国产亚洲精品综合一区在线观看 | 欧美乱码精品一区二区三区| 亚洲av五月六月丁香网| 日韩 欧美 亚洲 中文字幕| 女人高潮潮喷娇喘18禁视频| 色在线成人网| 日韩三级视频一区二区三区| 操出白浆在线播放| 亚洲熟女毛片儿| 久久中文字幕人妻熟女| 午夜福利成人在线免费观看| 男人舔女人的私密视频| 欧美日韩乱码在线| 99riav亚洲国产免费| 国产熟女xx| 久久人妻福利社区极品人妻图片| 怎么达到女性高潮| 男女做爰动态图高潮gif福利片 | 国产欧美日韩一区二区三区在线| 色综合站精品国产| 91精品国产国语对白视频| 在线免费观看的www视频| 老司机午夜福利在线观看视频| 咕卡用的链子| 大型av网站在线播放| 看片在线看免费视频| 久久国产乱子伦精品免费另类| 在线观看免费午夜福利视频| 亚洲精品中文字幕在线视频| 99精品久久久久人妻精品| 脱女人内裤的视频| 久久精品人人爽人人爽视色| 国产精品电影一区二区三区| 亚洲中文av在线| 久久影院123| 男女下面进入的视频免费午夜 | 成年人黄色毛片网站| 变态另类成人亚洲欧美熟女 | 国产精品乱码一区二三区的特点 | 欧美大码av| 村上凉子中文字幕在线| 中出人妻视频一区二区| 亚洲伊人色综图| 在线观看免费午夜福利视频| 国产一级毛片七仙女欲春2 | 中文字幕另类日韩欧美亚洲嫩草| 9热在线视频观看99| 免费观看人在逋| 成人精品一区二区免费| 久久香蕉国产精品| 国产精品一区二区在线不卡| 午夜福利欧美成人| www国产在线视频色| 不卡一级毛片| 久久久国产成人免费| 丝袜在线中文字幕| 日韩高清综合在线| 黄色成人免费大全| 成人免费观看视频高清| 久久精品亚洲熟妇少妇任你| 国产精品日韩av在线免费观看 | 悠悠久久av| cao死你这个sao货| 成人特级黄色片久久久久久久| 日韩高清综合在线| 亚洲成人免费电影在线观看| 亚洲国产精品成人综合色| 久久精品91蜜桃| 日韩高清综合在线| 国产乱人伦免费视频| 黄色视频,在线免费观看| 国产乱人伦免费视频| 国产精品久久久久久人妻精品电影| 老司机深夜福利视频在线观看| 宅男免费午夜| 国产成人精品久久二区二区免费| 美女高潮喷水抽搐中文字幕| 国产aⅴ精品一区二区三区波| 午夜福利欧美成人| 精品国内亚洲2022精品成人| www.999成人在线观看| 老司机深夜福利视频在线观看| 免费看十八禁软件| 激情在线观看视频在线高清| tocl精华| 亚洲中文字幕日韩| 久久精品91无色码中文字幕| 欧美一区二区精品小视频在线| 日本 欧美在线| 老熟妇乱子伦视频在线观看| 亚洲av熟女| 日本黄色视频三级网站网址| 欧美乱妇无乱码| 亚洲欧美激情在线| 亚洲七黄色美女视频| 香蕉久久夜色| 成人亚洲精品一区在线观看| 国产1区2区3区精品| 亚洲激情在线av| 色综合婷婷激情| 99热只有精品国产| 两个人看的免费小视频| 久久天堂一区二区三区四区| 一级毛片高清免费大全| 亚洲精品粉嫩美女一区| 国内精品久久久久精免费| 黄片小视频在线播放| 在线国产一区二区在线| 露出奶头的视频| 亚洲av成人一区二区三| 长腿黑丝高跟| 国产伦一二天堂av在线观看| 中文字幕另类日韩欧美亚洲嫩草| 中文字幕精品免费在线观看视频| www.999成人在线观看| www日本在线高清视频| 国产精品免费一区二区三区在线| 成人18禁高潮啪啪吃奶动态图| 18禁国产床啪视频网站| 亚洲成a人片在线一区二区| 婷婷六月久久综合丁香| www.精华液| 在线永久观看黄色视频| 国产激情欧美一区二区| av有码第一页| 色综合婷婷激情| 桃红色精品国产亚洲av| 国产午夜福利久久久久久| 亚洲五月婷婷丁香| 一级黄色大片毛片| 很黄的视频免费| 久久久国产欧美日韩av| 国产激情久久老熟女| 久久久久久国产a免费观看| 波多野结衣巨乳人妻| 亚洲av日韩精品久久久久久密| 欧美精品亚洲一区二区| 99riav亚洲国产免费| 夜夜看夜夜爽夜夜摸| 精品欧美一区二区三区在线| 亚洲国产看品久久| 成人三级做爰电影| 淫秽高清视频在线观看| 国产伦一二天堂av在线观看| 久久人妻熟女aⅴ| 国产欧美日韩一区二区三区在线| 欧美色欧美亚洲另类二区 | 国产成人系列免费观看| 级片在线观看| 88av欧美| 怎么达到女性高潮| 人人妻人人爽人人添夜夜欢视频| 免费在线观看视频国产中文字幕亚洲| 免费女性裸体啪啪无遮挡网站| 又黄又爽又免费观看的视频| 中文字幕另类日韩欧美亚洲嫩草| 99久久久亚洲精品蜜臀av| 一级作爱视频免费观看| 免费看美女性在线毛片视频| 免费观看精品视频网站| 老熟妇仑乱视频hdxx| 免费在线观看完整版高清|