• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    A novel stability prediction approach for thin-walled component milling considering material removing process

    2017-11-17 08:32:05JiahaoSHIQinghuaSONGZhanqiangLIUXingAI
    CHINESE JOURNAL OF AERONAUTICS 2017年5期

    Jiahao SHI,Qinghua SONG,Zhanqiang LIU,Xing AI

    Key Laboratory of High Efficiency and Clean Mechanical Manufacture,Ministry of Education,Shandong University,Ji’nan 250061,China

    School of Mechanical Engineering,Shandong University,Ji’nan 250061,China

    A novel stability prediction approach for thin-walled component milling considering material removing process

    Jiahao SHI,Qinghua SONG*,Zhanqiang LIU,Xing AI

    Key Laboratory of High Efficiency and Clean Mechanical Manufacture,Ministry of Education,Shandong University,Ji’nan 250061,China

    School of Mechanical Engineering,Shandong University,Ji’nan 250061,China

    The milling stability of thin-walled components is an important issue in the aviation manufacturing industry,which greatly limits the removal rate of a workpiece.However,for a thin-walled workpiece,the dynamic characteristics vary at different positions.In addition,the removed part also has influence on determining the modal parameters of the workpiece.Thus,the milling stability is also time-variant.In this work,in order to investigate the time variation of a workpiece’s dynamic characteristics,a new computational model is firstly derived by dividing the workpiece into a removed part and a remaining part with the Ritz method.Then,an updated frequency response function is obtained by Lagrange’s equation and the corresponding modal parameters are extracted.Finally,multi-mode stability lobes are plotted by the different quadrature method and its accuracy is verified by experiments.The proposed method improves the computational efficiency to predict the time-varying characteristics of a thin-walled workpiece.

    1.Introduction

    Due to its wide applications in military,energy,and aerospace industries,milling of thin-walled components is of great significance.However,the high flexibility of a cutting toolworkpiece system and improper cutting parameters contribute to severe vibration,and the most important source of the problems that emerge during thin-walled components milling is regenerative chatter.

    Regenerative chatter is a kind of self-excited vibrations,and the cutting amount simultaneously depends on the paths left by the tooth tips of the current tooth and the previous tooth,so the cutting force varies as well as the chip thickness.There are many methods proposed to predict chatter stability,including frequency-domain methods1–3and time-domain methods.4–8However,all the se studies assumed that the dynamic characteristics of a system did not change during the whole machining process.

    As for a thin-walled workpiece,due to the variation of the dynamic characteristic with the motion of the cutter position,the stability also changes during the machining process.Bravo et al.9and Sheng et al.10divided the milling process into different stages and obtained frequency responsefunctions(FRFs)through an impact test.Although this method would be more accurate,it was almost impractical to conduct enough impact tests to obtain a workpiece’s dynamic characteristic during milling.In order to avoid repeated impact tests,a workpiece’s FRF was updated by the finite element method(FEM).11–15However,this method is of low efficiency since a workpiece should be remodeled and correspondingly,modal analysis should also be re-conducted.In this condition,Budak et al.16and Song et al.17utilized a structural dynamic modification scheme to improve the FEM-based method,where only a workpiece’s initial dynamic characteristic was needed.Similarly,taking into consideration the influence of material removal and the change of the mode shape along the cutting path and tool axis,Yang et al.18also obtained in-process workpiece dynamics through structural dynamic modification.Neglecting the influence of material removal,Li et al.19obtained position-dependent FRFs through the effective stiffness which was dependent on mode shape.Instead of the commonly adopted FEM,the multispan plate(MSP)mode was proposed to model the varying thickness of a flexible pocketstructure.20Compared with FEM-based methods,the MSP model offers 10–20 times higher computational efficiency.Combining the high computational efficiency of the MSP model and the versatility of FEM-based methods,Ahmadi21proposed finite strip modeling(FSM)to model thin-walled structures in pocket milling operations.

    It is worth noting that due to the change of the mode shape along the cutting path,some specific modes may also affect the stability of a thin-walled workpiece.Based on frequency methods,Budak and Altintas22obtained the stability of a flexible multi-mode structure.However,the dynamic characteristic was assumed as unchanged.Thvenot et al.11,12took the first several modes into consideration and determined the stability limitation by selecting the lowest envelop of each mode.According to Ref.23,this lowest envelop method(LEM)may cause some prediction errors when the modes of a workpiece are not well separated.Zhang et al.24predicted the stability of a multi-mode cantilever plate and updated the dynamic characteristic by an impact test.Song et al.25took the influences of different modes into consideration.However,material removal was neglected.

    Based on the above literature review,it can be seen that often the dynamic characteristic of a workpiece was obtained by the FEM.Apart from the MSP method,the re is no other independent numerical method which is not involved with the FEM.In addition,Refs.11,12considering both multi modes and material removal did not give a clear explanation about the relationship between the position,mode shape,and stability limitation.This paper focuses on the mathematic model of a thin-walled flexible part,and tries to conduct the oretical analysis of the time-variant modal parameters of the workpiece.

    The contribution of this paper lies in that the influences of the cutter position and material removal is investigated by the oretical analysis.Since a system does not need to be remodeled during the machining process,compared with the finite element method,the calculation efficiency can be improved a lot.The remainder of this paper is summarized as follows.The equation of motion of the flexible thin-walled part and modal analysis are given in Section 2.Then,the different quadrature method is briefly introduced to calculate stability lobes in Section 3,and the milling stability prediction offlexible part milling and experimental results are presented in Section 4.Conclusions are drawn in the last section.

    2.Time-varying model of thin-walled plate

    As shown in Fig.1,during the milling process,the material is continuously removed along the trajectory of the moving cutter.Correspondingly,the workpiece’s dynamic characteristics,such as natural frequency and stiffness,also change during this process.In this section,different from Refs.16–18,where the FEM is used to conduct modal analysis,a more efficient method is proposed to obtain the dynamic characteristics of the workpiece.

    2.1.Energy formula

    In Fig.1,a cantilevered thin-walled rectangular plate under milling machining,with a length of L,a width of W,and a thickness of h,is modeled.The spindle speed is Ω and the feed rate is c.The classical plate the ory,which is suitable for thinwalled plate analysis,is used,and only the bending effect of the thin-walled plate is considered.Since,during the milling process,the material is removed as the cutter moves along the cutting path,the shape of the plate is varying during this period.However,it is lucky that the shape of the plate is predictable,and the material removal volume is relatively small compared to that of the unprocessed plate.Therefore,it is reasonable to assume that the plate’s modal shape is unchanged and correspondingly,the kinetic energy,T,of the machined plate can be expressed as

    where ρ is the density,hris the thickness of the removed part,namely the radial cutting depth,w is the displacement along z direction,and the over-dot denotes differentiation with respect to time.It should be mentioned that A represents the surface area of the unprocessed plate while Ar(t)stands for that of the removed part,which is a function of the time.

    Fig.1 Model of a cantilevered plate.

    Similarly,the potential energy V*of the machined plate can be calculated as

    wheref(x,y)is a function of x and y,and D*and Dr*are the complex flexural rigidities of the unprocessed plate and removed part,respectively,which are given by

    where μ is the poisson ratio,E is the elastic module,i is an imaginary unit,and γ is the loss factor of the w*orkpiecefixture system.To distinguish from a real number,‘’is added in the upper right corner of the complex number.

    In this paper,the Rayleigh-Ritz method(RRM)is used to approximately express the transverse displacement w.The Rayleigh-Ritz solutions for this problem are of the following form

    where N is the number of Rayleigh-Ritz terms,qij(t)is the Rayleigh-Ritz coefficients,and ξi(x)and ηj(y)are admissible functions. ξi(x)and ηj(y)arefound by solving the clampedfree beam function and free-free beam function,respectively,which are expressed as26

    where αiand βjare roots of the characteristic equation,and satisfy coshαicosαj=-1 and coshβicosβj=1,respectively.

    Since the main aim is to extract the modal parameters,the external work done by the milling force is neglected.Therefore,the Lagrange of this system without a load is La=T-V*,where T and V*are the kinetic energy and strain energy obtained by Eqs.(1)and(2).The equation of motion of the system obtained by Lagrange’s equation is shown as

    where the double-over-dot denotes second-order differentiation with respect to time,0 is the column vector of N2×1,q(t)=[q11(t),q12(t),...,qNN(t)]T.For the machining condition shown in Fig.1,where the cutter moves from the left to the right,the radial cutting depth is ar,and the axial cutting depth is aa,so matrices S and U*can be calculated by

    and

    In Eqs.(8)and(9),u=m+(i-1)×N and v=n+(j-1)× N,where i,j,m,and n=1,2,...,N.(·)i,xrepresents first-order differentiation with respect to x,which is similar to(·)i,xx,(·)j,y,and(·)j,yy.

    It should be mentioned that Eqs.(1)–(10)show the process to obtain the governing equation of the cantilevered rectangular plate.For more complex workpieces,such as thin-walled plates and shells with different shapes,boundary conditions,and varying thickness,some mathematic skills are needed to deal with the m(e.g.,skills mentioned in Ref.27).Of course,for some quite complicated shapes,some reasonable simplifications are also needed.

    2.2.Modal analysis

    Eq.(7)describes the governing motion of the plate’s free vibration,and can be used to extract the natural frequencies and loss factors of different modes.Assuming q(t)in the form ofˉq exp (iλt),Eq.(7)can be rewritten as

    Since the stiffness matrix U*is a complex matrix,the generalized eigenvalue λ2is also a complex number.As a result,the derived complex eigenvalue problem,Eq.(11),gives the rorder natural frequency ωrand loss factor γras follows

    where Re[·]and Im[·]mean the real and imaginary parts,respectively.For a small loss factor,it has the following relationship with the damping ratio,ζr

    It should be mentioned that the loss factor of the workpiece-fixture system is different from that of a specific mode and should befirstly determined by a modal test.According to Eq.(13),the loss factor of a specific mode can be obtained by a modal experiment and the n based on Eq.(12),the loss factor of the workpiece-fixture system can be determined by the iteration method.

    Apart from the natural frequency and loss factor of each mode,the FRF of the treated plate is now of primary interest.Assuming a unit harmonic point load applied at point(xin,yin),the FRF with a response at point(xre,yre)can be calculated as

    where W(x,y)=[ξ1(x)η1(y),ξ2(x)η2(y),...,ξN(x)ηN(y)]T,and S and U*are calculated by Eqs.(8)–(10),respectively.After the calculation of the FRF,the rational fraction polynomials algorithm is adopted to fit the FRF curves to obtain the modal parameters.28

    3.Milling stability with multiple modes

    As shown in Fig.2,since the workpiece is flexible as compared to the tool,here,only the traverse vibration and cutting force in y-direction are considered.When considering n modes of the workpiece,the motion of equation can be expressed as

    where M=diag(m1,m2,...,mn),C=diag(c1,c2,...,cn),K=diag(k1,k2,...,kn),and Z(t)=aahz(t)[φ1,φ2,...,φn]T×[φ1, φ2,..., φn]which is periodic with Tp.mi,ci,and kirepresent the ith-order modal mass,damping,and stiffness,respectively.The term φistands for the ith-order mode shape of the cutter position and

    In Eq.(16),Ntis the number of cutter teeth,and Ktand Knare the tangential and normal linearized cutting force coefficients,respectively.φj(t)is the angular position of tooth j,and g(φj(t))is the switching function,which can be defined as

    where φstand φexare the start and exit angles of tooth j.

    Fig.2 Single degree-of-freedom milling system.

    Here,in this paper,the different quadrature method(DQM)is used to approximate the original delay differential equation(DDE)(Eq.(15))as a set of algebraic equations and the n construct a Floquet transition matrix for milling stability analysis.The DQM was originally introduced by Bellman to solve partial differential equations(PDEs).29Then it has been widely used in engineering and physics problems.The basic idea of the DQM is that a partial derivative of a function with respect to a coordinate direction at a sampling grid point within an interval along that direction can be approximated as a linear weighted sum of all the function values at the sampling grid points within the whole interval.Compared with other well-known approximation methods,such as the semi-discretized technique,the advantages of this semianalytical time-domain method are its simplicity and high computational efficiency.More details about this method are described in Ref.30

    Thefirst step of the DQM is re-expressing Eq.(15)as the following state-spaceform

    Considering the characteristic of the milling process,one can assume that the time interval[0,Tp]is composed of a free vibration period,[0,tf],and a forced vibration period,[tf,Tp],during which the cutter contacts with the workpiece.For the first time interval,the state of the system at the end of the free vibration duration t=tfcan be analytically expressed as

    Denoting the time span of the forced vibration duration Tc=Tp-tf,and letting τ=(t-tf)/Tcas the nondimensional time,Eq.(17)can be re-expressed as

    For the normalized second time interval[0,1],it can be discretized by the sampling grid points τi,i=0,1,...,m.According to the idea of the DQM,each component of the derivative,˙~x(τ),can be expressed as the weighted linear sums of~x(τ)at all the sampling grid points.Therefore,for each component of˙~x(τi),i=1,2,...,m,it can be rewritten in the following discreteform

    where?is the Kronecker product defined for two matrices A and B so that A ? B=[AijB],I2n×2nis the 2n×2n identity matrix,and D is a matrix with an order of m×(m+1)and calculated by the following mth-order Lagrange polynomial

    In this paper,Chebyshev-Gauss-Lobatto sampling grid points are used to determine the value of each τi.

    Finally,by noting that ti=tf+τiTcand combining Eqs.(19)–(21),the state transition relationship can be obtained as follows

    The stability of Eq.(15)can be approximated by the Floquet transition matrix Φ = Ψ-1Γ.Note that the integer m determines the dimension of matrices in Eq.(23)and the precision of the results.

    4.Case study and experimental verification

    4.1.Numerical study

    The previous analysis provides a the oretical method to predict the stability of thin-workpiece milling considering material removal and changes of the tool position.In this section,before conducting numerical and experimental analysis,the process to compute the stability lobe diagram(SLD)is firstly described.As shown in Fig.3,firstly,the loss factor is extracted from the modal experiment,and the material removal is determined by the cutting position.Based on the the oretical analysis in Section 2.1,the energy expression of the workpiece can be calculated.Then,based on Eqs.(11)and(12),the natural frequencies and FRFs of different positions of the workpiece can also be obtained.The modal parameters are extracted from the FRFs with the method mentioned in Section 2.2,and finally,the milling stability can be predicted with the extracted modal parameters.

    In this section,the geometrical parameters of the cantilever plate are listed in Table 1.The radial immersion ratio is fixed as 0.033,and the tangential and normal cutting force coefficients are Kt=6×108N/m2and Kn=2×108N/m2,respectively.A milling cutter with four edges is used in the down milling process.

    In order to describe the dynamic characteristics of the plate,as shown in Fig.4(a),eleven evenly distributed points are selected along the cutter path.Fig.4(b)and(c)illustrates the first two mode shapes of the plate.It can be seen that in the first mode shape,the points along the cutter path share similar deformation,while differ from each other in the second mode shape.It should be mentioned that the re is a node in the middle area of the cutter path.This regulation is also reflected in Fig.5.

    As described in Fig.3,firstly,a modal experiment is needed to obtain the loss factor of the workpiece before milling.It should be mentioned that,due to the existence of the node in the second mode,the impact point should not be selected in the middle of the plate,where the second mode cannot be excited.Therefore,as shown in Fig.4(a),the excited points are selected in the right upper corner of the plate.In this paper,due to the small difference between the damping ratios of first two modes,the loss factor of the system is assumed as the average of those of the first two modes.Based on the theoretic analysis in Sections 2.1 and 2.2,the first two natural frequencies at the se points are calculated and shown in Fig.6.The small difference between the results calculated by the presented method and the FEM verifies the accuracy of the previous the oretical analysis.It is obvious that the re is an increasing trend for the first mode(from 869 Hz to 876 Hz),while a sinuous trend for the second mode(between 1627 Hz and 1632 Hz).This may be because,in the first mode,with the remove of the material,a decrease of the mass results in a rise of the natural frequency.However,in the second mode,due to the sinuous mode shape along the se points,the natural frequency also presents a similar trend.

    Fig.3 Process to predict the SLD.

    Table 1 Geometrical parameters of the workpiece.

    Fig.4 Cutter positions of the flexible plate and its first two mode shapes.

    Fig.5 Normalized mode shapes of the cutting points of the first two modes.

    Fig.7 gives the experimental and the oretical FRFs of the workpiece.The overlap between the se two kinds of curves around the peak area also shows the reliability of the presented method.It is clear that with the moving of the cutter,the first mode almost remains unchanged,while the second mode firstly decays and the n disappears at point x=50 mm.After that,from points 50 mm to 100 mm,this mode shows a reverse trend and increases gradually.This phenomenon may account for the mode shape of the second mode,where the re is a node in the middle area of the plate.Based on Section 2.2,modal parameters are extracted from the FRFs and listed in Table 2.It can be seen that the first mode’modal parameters are almost identical to each other.However,for the second mode,the se three modal parameters all show an increasing trend from 0–50 mm and decreasing from 50 mm to 100 mm.It is easy to understand that the node at x=50 mm makes this area a rigid point.

    Fig.8 shows the SLDs of the se eleven points.As shown in Fig.8(a),the SLD of point x=0 is determined by the SLDs of both modes,which means that the bold solid line(SLD considering both modes)is the lowest envelope of the thin dash line(SLD of the first mode)and the thin solid line(SLD of the second mode).A similar phenomenon also exits in other positions.According to Ref.23,this is because the modes of the workpiece are well separated.However,when the se modes are close to each other and the contributions of other modes cannot be neglected,the zero-order approximation(ZOA)method can be used to calculate the SLD.Compared to the SLD of point 0,the SLD of the second mode is improved,and the bold solid line is mainly determined by the thin dash line.This trend also shows at points 2,3,4,and 5,and finally,in the middle point 5,the bold solid line totally overlaps with the thin dash line,which means that the SLD can be accurately calculated by only considering the first mode.This is because the node of the second mode can be considered as a fixed point,which means that chatter cannot occur and the limited depth approaches to an infinite value.In Fig.8,symbols‘+’, ‘×’,and ‘*’represent three different spindle speeds,namely 4200 r/min,5700 r/min,and 6500 r/min.It is easy to find that due to the variation of the SLD,stable zones and unstable zones are distributed in different regions.For symbol‘+’,the stable zone is predicted as 0–10 mm and 90–100 mm,while the unstable zone is 10–90 mm.Since symbol ‘×’is always below the SLD curve,the region is in a stable condition.As for symbol ‘*’,the regions in 0–20 mm and 80–100 mm are predicted as the stable zone,while that in 20–80 mm as the unstable zone.

    Fig.6 Variations of the first two natural frequencies.

    Fig.7 FRFs of different cutter positions.Solid lines:the oretic FRFs;dash lines:experimental FRFs.

    4.2.Experimental verification

    A milling experiment is carried out by a high-speed machining center VMC0540d with the maximum spindle speed of 30000 r/min.A GRAS 40PP microphone with a sensitivity of 50 mV/Pa is used to measure the sound pressure.The machined surface topography is also checked by a laser microscope(Keyence VK-X250).The milling experimental equipment is shown in Fig.9.The material of the workpiece is aluminum alloy 7075,whose geometric parameters are listed in Table 1,and that of the tool is cemented carbide.

    The surface topography on the machined workpiece and the sound signal during the milling process are shown in Fig.10.Chatter marks are clear from the surface topography,and the surface of the stable zone is smooth with a lower roughness value in a spindle speed of 4200 r/min.In addition,the sound pressure during the milling process also shows a recognizable change.In the periods of 0–0.4 s and 3.7–4 s,the magnitude of the sound pressure is getting large obviously(about 10 Pa).However,for the time from 0.4 s to 3.7 s,the sound pressure shows a significant decrease to around 3.5 Pa.Correspondingly,the unstable zone,determined by the sound pressure,is 0–10 mm and 87.5–100 mm,while the stable zone is 10–87.5 mm.In Fig.10(b),during the milling period,the sound pressure stands at a small value,approximately 5 Pa.Meanwhile,the re are also no chatter marks in the surface topography in a spindle speed of 5700 r/min.Therefore,all the regions are in a stable condition.In a spindle speed of 6500 r/min(see Fig.10(c)),the re are three different areas in the sound pressure,namely 0–0.75 s,0.75–3.25 s,and 3.25–4 s.In the first and third time periods,both magnitudes are in higher values,about 20 Pa,which is higher than that in the second period,only around 3 Pa.Therefore,the correspondingly measured unstable zone in this milling condition is 0–18.75 mm and 81.25–100 mm,while the stable zone is 18.75–81.25 mm.Chatter marks in the surface topography during the third time period also reflect the existence of chatter.In the comparisons of the ranges of the stable domain and the chatter domain between experimental and theoretical analysis in Section 4.1,two results are in good agreement.Thus,the correctness of the proposed method can be verified.

    Table 2 The first two modal parameters.

    Fig.8 Dynamic SLDs of the milling process with different modes.

    Fig.9 Experimental setup.

    5.Conclusions

    (1)A highly efficient numerical method is proposed to obtain the dynamic characteristics of a thin-walled workpiece,and the extracted modal parameters are used to plot multi-mode stability lobes.

    (2)During the material removal process,the first-order natural frequency shows a growing trend,increasing from 869 Hz to 876 Hz.However,the second-order natural frequency firstly increases from 1627 Hz to 1632 Hz and the n decreases to 1628 Hz.After that,this natural frequency reaches its maximum value(1633 Hz)at the end of the milling process.

    Fig.10 Time waves of sound pressure and surface topography.

    (3)The first two modal parameters have different influences on the milling stability at different cutting positions.In the two ends of the cutting area,the limited axial depth is mainly determined by the second modal parameters.On the contrary,the stability lobes are only affected by the first modal parameters.

    (4)The computation results are in agreement with experimental data.

    Acknowledgements

    This study was co-supported by the National Natural Science Foundation of China(No.51575319),the Young Scholars Program of Shandong University(No.2015WLJH31),the Major National Scienceand Technology Project(No.2014ZX04012-014),and the Tai Shan Scholar Foundation(No.TS20130922).

    1.Altintas Y.Manufacturing automation:metal cutting mechanics,machine tool vibration,and CNC design.2nd ed.New York:Cambridge University Press;2012.

    2.Budak E,Altintas Y.Analytical prediction of chatter stability in milling-part II:general formulation.J Dyn Syst–T ASME 1998;120(1):22–30.

    3.Zhou X,Zhang DH,Luo M,Wu BH.Chatter stability prediction in four-axis milling of aero-engine casings with bull-nose end mill.Chinese J Aeronaut 2015;28(6):1766–73.

    4.Luo M,Mei JW,Zhang DH.Time-domain modeling of a cutter exiting a workpiece in the slot milling process.Chinese J Aeronaut 2015;29(6):1852–8.

    5.Davies MA,Pratt JR,Dutterer B,Burns TJ.Stability prediction for low radial immersion milling.Trans ASME J Manuf Sci Eng 2002;124(2):217–25.

    6.Faassen RPH,Wouw VDN,Nijimeijer H,Oosterling JAJ.An improved tool path model including periodic delay for chatter prediction in milling.J Comput Nonlinear Dyn 2007;2(2):167–79.

    7.Totis G,Albertelli P,Sortino M,Monno M.Efficient evaluation of process stability in milling with spindle speed variation by using the Chebyshev collocation method.J Sound Vib 2014;333(3):646–68.

    8.Ozoegwu CG.Least squares approximated stability boundaries of milling process.Int J Mach Tool Manuf 2014;79(4):24–30.

    9.Bravo U,Altuzarra O,Lopez LNLD,Sanchez JA.Stability limits of milling considering the flexibility of the workpiece and the machine.Int J Mach Tool Manuf 2005;45(15):1669–80.

    10.Sheng Q,Zhao JB,Wang TR.Three-dimensional stability prediction and chatter analysis in milling of thin-walled plate.Int J Adv Manuf Tech 2011;86(5–8):1–10.

    11.Thevenot V,Arnaud L,Dessein G,Cazenave LG.Integration of dynamic behaviour variations in the stability lobes method:3D lobes construction and application to thin-walled structure milling.Int J Adv Manuf Tech 2006;27(7):638–44.

    12.Thevenot V,Arnaud L,Dessein G,Cazenave LG.Influence of material removal on the dynamic behavior of thin-walled structures in peripheral milling.Mach Sci Technol 2006;10(3):275–87.

    13.Tang A,Liu Z.Three-dimensional stability lobe and maximum material removal rate in end milling of thin-walled plate.Int J Adv Manuf Tech 2009;43(1):33–9.

    14.Adetoro O,Sim W,Wen P.An improved prediction of stability lobes using nonlinear thin wall dynamics.J Mater Process Technol 2010;210(6–7):969–79.

    15.Biermann D,Kersting P,Surmann T.A general approach to simulating workpiece vibrations during five-axis milling of turbine blades.CIRP Ann – Manuf Technol 2010;59(1):125–8.

    16.Budak E,Tunc LT,Alan S,Hozgven HN.Prediction of workpiece dynamics and its effects on chatter stability in milling.CIRP Ann–Manuf Technol 2012;61(1):339–42.

    17.Song QH,Liu ZQ,Wan Y,Ju GG,Shi JH.Application of Sherman–Morrison–Woodbury formulas in instantaneous dynamic of peripheral milling for thin walled component.Int J Mech Sci 2015;96–97:79–90.

    18.Yang Y,Zhang WH,Ma YC,Wan M.Chatter prediction for the peripheral milling of thin-walled workpieces with curved surfaces.Int J Mach Tool Manu 2016;109:36–48.

    19.Li ZY,Sun YW,Guo DM.Chatter prediction utilizing stability lobes with process damping in finish milling of titanium alloy thinwalled workpiece.Int J Adv Manuf Technol 2017;89(9):2663–74.

    20.Meshreki M,Attia H,Kovecses J.Development of a new model for the varying dynamics offlexible pocket-structures during machining.J Manuf Sci E–T ASME 2011;133(4):041002.

    21.Ahmadi K.Finite strip modeling of the varying dynamics of thinwalled pocket structures during milling.Int J Adv Manuf Tech 2017;89(9):2691–9.

    22.Budak E,Altintas Y.Analytical prediction of chatter stability in milling-part II:application of the general formulation to common milling system.J Dyn Syst– T ASME 1998;120(1):31–6.

    23.Wan M,Ma YC,Zhang WH,Yang Y.Study on the construction mechanism of stability lobes in milling process with multiple modes.Int J Adv Manuf Technol 2015;79(1):589–603.

    24.Zhang XJ,Xiong CH,Ding Y.A new solution for stability prediction in flexible part milling.In:Jeschke S,Liu HH,Schiberg D,editors.Intelligent robotics and applications.Berlin:Springer;2011.p.452–64.

    25.Song QH,Shi JH,Liu ZQ,Wan Y.A time-space discretization method in milling stability prediction of thin-walled component.Int J Adv Manuf Technol 2017;89(9):2675–89.

    26.Moradi H,Vossoughi G,Behzad M,Movahhedy MR.Vibration absorber design to suppress regenerative chatter in nonlinear milling process:application for machining of cantilever plates.Appl Math Model 2015;39(2):600–20.

    27.Chakraverty S.Vibration of plates.New York:CRC Press;2009.28.Richardson MH,Formenti DL.Parameter estimation from frequency response measurements using rational fraction polynomials. First international modal analysis conference 1982;1982:167–81,Florida,USA.New York:Springer.

    29.Bellman R,Casti J.Differential quadrature and long-term integration.Math Anal Appl 1971;34(2):235–8.

    30.Ding Y,Zhu LM,Zhang XJ,Ding H.Stability analysis of milling via the differential quadrature method.Trans ASME J Manuf Sci E 2013;135(4):1–10.

    5 December 2016;revised 1 January 2017;accepted 13 February 2017

    Available online 8 June 2017

    Material removal effect;

    Multi-mode;

    Stability;

    Thin-walled workpiece;

    Vibration

    *Corresponding author at:Key Laboratory of High Efficiency and Clean Mechanical Manufacture,Ministry of Education,Shandong University,Ji’nan 250061,China.

    E-mail address:ssinghua@sdu.edu.cn(Q.SONG).

    Peer review under responsibility of Editorial Committee of CJA.

    Production and hosting by Elsevier

    http://dx.doi.org/10.1016/j.cja.2017.05.011

    1000-9361?2017 Chinese Society of Aeronautics and Astronautics.Production and hosting by Elsevier Ltd.

    This is an open access article under the CC BY-NC-ND license(http://creativecommons.org/licenses/by-nc-nd/4.0/).

    ?2017 Chinese Society of Aeronautics and Astronautics.Production and hosting by Elsevier Ltd.This is an open access article under theCCBY-NC-NDlicense(http://creativecommons.org/licenses/by-nc-nd/4.0/).

    中文字幕高清在线视频| 国产精品久久久久久人妻精品电影| 精品国产乱码久久久久久男人| 国产亚洲av嫩草精品影院| 亚洲国产精品久久男人天堂| av电影中文网址| 不卡一级毛片| 中文字幕人妻丝袜一区二区| 1024手机看黄色片| 国产激情欧美一区二区| 欧美亚洲日本最大视频资源| 日韩三级视频一区二区三区| 亚洲人成电影免费在线| 日日夜夜操网爽| 在线观看www视频免费| 国产蜜桃级精品一区二区三区| 日本免费a在线| 国产精品美女特级片免费视频播放器 | 国产又黄又爽又无遮挡在线| 国产精品1区2区在线观看.| 一级a爱片免费观看的视频| 天天添夜夜摸| 日本撒尿小便嘘嘘汇集6| 国产激情欧美一区二区| 人人妻,人人澡人人爽秒播| 美女高潮到喷水免费观看| 欧美成狂野欧美在线观看| 欧美另类亚洲清纯唯美| 人妻久久中文字幕网| 变态另类成人亚洲欧美熟女| 日韩大尺度精品在线看网址| 91老司机精品| 久久久久免费精品人妻一区二区 | 国产又爽黄色视频| 欧美黑人欧美精品刺激| 亚洲av电影在线进入| 日韩av在线大香蕉| 1024手机看黄色片| 精品午夜福利视频在线观看一区| 淫妇啪啪啪对白视频| 男男h啪啪无遮挡| 亚洲欧美精品综合一区二区三区| 亚洲国产欧美日韩在线播放| 最好的美女福利视频网| 一进一出好大好爽视频| 国产一区二区在线av高清观看| 亚洲av成人av| 国内毛片毛片毛片毛片毛片| 极品教师在线免费播放| 黄色视频不卡| 99精品欧美一区二区三区四区| 一二三四在线观看免费中文在| 可以在线观看毛片的网站| www国产在线视频色| 一区二区三区精品91| 免费观看人在逋| 在线免费观看的www视频| 亚洲性夜色夜夜综合| 在线永久观看黄色视频| 亚洲国产欧洲综合997久久, | 观看免费一级毛片| 国产亚洲精品一区二区www| 变态另类成人亚洲欧美熟女| 妹子高潮喷水视频| 亚洲无线在线观看| 欧美成人免费av一区二区三区| 两性午夜刺激爽爽歪歪视频在线观看 | 国产野战对白在线观看| 中文字幕另类日韩欧美亚洲嫩草| 欧美另类亚洲清纯唯美| 久久久久免费精品人妻一区二区 | 午夜福利18| 搡老岳熟女国产| 成人手机av| 精品熟女少妇八av免费久了| 黄色片一级片一级黄色片| 俺也久久电影网| 视频区欧美日本亚洲| a在线观看视频网站| 久久天躁狠狠躁夜夜2o2o| 午夜福利视频1000在线观看| 欧美丝袜亚洲另类 | 97超级碰碰碰精品色视频在线观看| 国产亚洲精品综合一区在线观看 | 欧美激情高清一区二区三区| 欧美日韩亚洲国产一区二区在线观看| 婷婷精品国产亚洲av| 日韩精品免费视频一区二区三区| 国产成人影院久久av| 黄片播放在线免费| 97碰自拍视频| 精品国产乱码久久久久久男人| 91麻豆av在线| 一级黄色大片毛片| 免费在线观看完整版高清| 男人操女人黄网站| 亚洲一区二区三区不卡视频| 国内揄拍国产精品人妻在线 | 欧美激情久久久久久爽电影| 国产欧美日韩一区二区三| 十八禁人妻一区二区| 国内久久婷婷六月综合欲色啪| 国产黄片美女视频| 久久精品影院6| 日本一区二区免费在线视频| 日韩精品中文字幕看吧| 宅男免费午夜| x7x7x7水蜜桃| 99国产精品一区二区三区| 精品国产一区二区三区四区第35| 国产精华一区二区三区| 色播在线永久视频| av欧美777| 高清毛片免费观看视频网站| 精品高清国产在线一区| 日本五十路高清| 午夜亚洲福利在线播放| 最新美女视频免费是黄的| 国产高清视频在线播放一区| а√天堂www在线а√下载| 亚洲精品国产一区二区精华液| 亚洲精品一卡2卡三卡4卡5卡| 91麻豆精品激情在线观看国产| 1024视频免费在线观看| 99国产精品99久久久久| 国产野战对白在线观看| av超薄肉色丝袜交足视频| 天堂影院成人在线观看| 欧美一区二区精品小视频在线| videosex国产| 亚洲精品国产一区二区精华液| 午夜两性在线视频| 欧美日韩中文字幕国产精品一区二区三区| 精品欧美一区二区三区在线| 一边摸一边做爽爽视频免费| 嫩草影院精品99| 久久精品国产99精品国产亚洲性色| 亚洲午夜精品一区,二区,三区| 18禁国产床啪视频网站| 两人在一起打扑克的视频| 久久久久国产精品人妻aⅴ院| 国产精品久久久人人做人人爽| 后天国语完整版免费观看| 亚洲午夜理论影院| 国产一卡二卡三卡精品| xxxwww97欧美| 亚洲中文字幕日韩| 国产精品av久久久久免费| 99热这里只有精品一区 | 日本一本二区三区精品| 午夜福利18| 久久天躁狠狠躁夜夜2o2o| 啦啦啦观看免费观看视频高清| 欧美又色又爽又黄视频| 久久久久国内视频| 久久久久免费精品人妻一区二区 | 亚洲人成电影免费在线| 国产精品一区二区精品视频观看| 色综合站精品国产| 国产高清videossex| 999精品在线视频| 俄罗斯特黄特色一大片| 久久热在线av| 亚洲 国产 在线| 黄频高清免费视频| 久久人妻av系列| 久久精品人妻少妇| www.www免费av| 一区二区三区国产精品乱码| 男人舔女人下体高潮全视频| 亚洲成人久久爱视频| 亚洲专区字幕在线| 中文字幕人妻丝袜一区二区| 国产亚洲欧美精品永久| 精品国产亚洲在线| 日日干狠狠操夜夜爽| 欧美大码av| 男人舔奶头视频| 久久久久久久精品吃奶| 黄色毛片三级朝国网站| 日韩精品免费视频一区二区三区| 美女 人体艺术 gogo| 免费无遮挡裸体视频| 亚洲精品美女久久久久99蜜臀| 十分钟在线观看高清视频www| 白带黄色成豆腐渣| 亚洲精品国产精品久久久不卡| 特大巨黑吊av在线直播 | 国产极品粉嫩免费观看在线| 少妇熟女aⅴ在线视频| 久久人人精品亚洲av| 亚洲狠狠婷婷综合久久图片| 精品久久久久久久久久久久久 | 男女做爰动态图高潮gif福利片| 国产熟女午夜一区二区三区| 欧美日韩精品网址| 亚洲无线在线观看| 国产成人av激情在线播放| 91成人精品电影| 一区二区三区精品91| 搡老熟女国产l中国老女人| 久久天堂一区二区三区四区| 欧美中文日本在线观看视频| 亚洲国产欧美日韩在线播放| 欧美zozozo另类| 国产成人av激情在线播放| 亚洲美女黄片视频| 操出白浆在线播放| 欧美精品亚洲一区二区| 搡老妇女老女人老熟妇| 一级毛片女人18水好多| 午夜福利欧美成人| 午夜老司机福利片| 国产99白浆流出| 午夜亚洲福利在线播放| 男男h啪啪无遮挡| 日韩三级视频一区二区三区| 人妻久久中文字幕网| 老熟妇仑乱视频hdxx| 国产黄色小视频在线观看| 亚洲人成网站高清观看| 在线观看一区二区三区| 在线看三级毛片| 亚洲人成网站在线播放欧美日韩| 亚洲人成77777在线视频| 99热这里只有精品一区 | 在线观看舔阴道视频| 日韩欧美三级三区| 日本在线视频免费播放| 日韩中文字幕欧美一区二区| 亚洲第一青青草原| 悠悠久久av| 波多野结衣巨乳人妻| 成人一区二区视频在线观看| 最近最新中文字幕大全电影3 | 男女午夜视频在线观看| 亚洲久久久国产精品| 禁无遮挡网站| 高潮久久久久久久久久久不卡| 99久久久亚洲精品蜜臀av| 国产黄a三级三级三级人| 女警被强在线播放| 黑人操中国人逼视频| 亚洲国产毛片av蜜桃av| 亚洲国产精品成人综合色| 校园春色视频在线观看| 精品不卡国产一区二区三区| 久久精品影院6| 视频在线观看一区二区三区| 久久伊人香网站| av免费在线观看网站| 香蕉av资源在线| 国产国语露脸激情在线看| 白带黄色成豆腐渣| 他把我摸到了高潮在线观看| 久久九九热精品免费| 黄色毛片三级朝国网站| 丁香欧美五月| 青草久久国产| 热re99久久国产66热| 久久国产乱子伦精品免费另类| 精品免费久久久久久久清纯| 熟女少妇亚洲综合色aaa.| 久久国产精品影院| 99热只有精品国产| 欧美色视频一区免费| 欧美最黄视频在线播放免费| 午夜免费成人在线视频| 久久精品国产亚洲av高清一级| 日韩欧美在线二视频| 亚洲熟女毛片儿| 精品免费久久久久久久清纯| 女人爽到高潮嗷嗷叫在线视频| 男女做爰动态图高潮gif福利片| 国产亚洲欧美98| 亚洲一区二区三区色噜噜| 老鸭窝网址在线观看| 女人爽到高潮嗷嗷叫在线视频| 99在线人妻在线中文字幕| 日韩欧美国产在线观看| 国内揄拍国产精品人妻在线 | 亚洲国产欧美日韩在线播放| 欧美成狂野欧美在线观看| 国产乱人伦免费视频| 少妇裸体淫交视频免费看高清 | 岛国在线观看网站| 免费观看人在逋| 一区二区三区国产精品乱码| 国产亚洲欧美在线一区二区| 日日爽夜夜爽网站| 变态另类丝袜制服| 高潮久久久久久久久久久不卡| 黄色女人牲交| 国产激情久久老熟女| 亚洲真实伦在线观看| 国产熟女午夜一区二区三区| 久久婷婷成人综合色麻豆| 又大又爽又粗| 又紧又爽又黄一区二区| cao死你这个sao货| 免费无遮挡裸体视频| 免费女性裸体啪啪无遮挡网站| 国产激情偷乱视频一区二区| 久久久久久国产a免费观看| 日本一本二区三区精品| 精品乱码久久久久久99久播| 中文在线观看免费www的网站 | 在线观看午夜福利视频| 亚洲五月色婷婷综合| 日韩av在线大香蕉| 白带黄色成豆腐渣| 亚洲国产欧美一区二区综合| 老司机在亚洲福利影院| 亚洲精华国产精华精| 两性午夜刺激爽爽歪歪视频在线观看 | 丝袜美腿诱惑在线| 韩国av一区二区三区四区| 琪琪午夜伦伦电影理论片6080| 精品国产乱子伦一区二区三区| 久久天堂一区二区三区四区| 制服人妻中文乱码| 免费在线观看完整版高清| 国产片内射在线| 亚洲国产看品久久| 午夜福利成人在线免费观看| 美女免费视频网站| 精品日产1卡2卡| 免费看a级黄色片| 国产国语露脸激情在线看| 一区二区三区高清视频在线| 操出白浆在线播放| 亚洲成人久久性| 一本一本综合久久| 老司机靠b影院| 亚洲国产欧美一区二区综合| 久久国产亚洲av麻豆专区| 久久国产精品男人的天堂亚洲| 久久久久九九精品影院| 成人一区二区视频在线观看| 欧美av亚洲av综合av国产av| 久久精品91无色码中文字幕| 亚洲精品av麻豆狂野| 97人妻精品一区二区三区麻豆 | 一本精品99久久精品77| 此物有八面人人有两片| 欧美在线一区亚洲| 50天的宝宝边吃奶边哭怎么回事| 此物有八面人人有两片| 最近最新免费中文字幕在线| 亚洲 欧美一区二区三区| 97人妻精品一区二区三区麻豆 | 好看av亚洲va欧美ⅴa在| 90打野战视频偷拍视频| 国产熟女xx| 国产精品自产拍在线观看55亚洲| 好看av亚洲va欧美ⅴa在| 亚洲av电影在线进入| 热re99久久国产66热| 久久久国产精品麻豆| 看片在线看免费视频| 亚洲中文av在线| 一级毛片精品| 欧美性猛交黑人性爽| 国产精品野战在线观看| 嫩草影院精品99| 91在线观看av| 久久久水蜜桃国产精品网| 在线播放国产精品三级| 999久久久国产精品视频| 国产精品久久久久久人妻精品电影| 国产免费男女视频| 男女做爰动态图高潮gif福利片| 嫁个100分男人电影在线观看| 国产免费男女视频| 久久久久久久久久黄片| 色综合欧美亚洲国产小说| 欧美一区二区精品小视频在线| 啪啪无遮挡十八禁网站| 色播在线永久视频| 91麻豆精品激情在线观看国产| 精品熟女少妇八av免费久了| 午夜激情av网站| 哪里可以看免费的av片| 桃色一区二区三区在线观看| 夜夜看夜夜爽夜夜摸| 一夜夜www| 麻豆一二三区av精品| 两个人免费观看高清视频| 国产日本99.免费观看| 精品国产超薄肉色丝袜足j| 两个人视频免费观看高清| 成人精品一区二区免费| 国产欧美日韩一区二区三| 国产精品亚洲av一区麻豆| 国产成人欧美| 视频在线观看一区二区三区| 国产精品亚洲美女久久久| 亚洲精品美女久久av网站| 精品日产1卡2卡| 亚洲精品在线观看二区| 国产熟女午夜一区二区三区| 侵犯人妻中文字幕一二三四区| 国产成人影院久久av| 亚洲 欧美 日韩 在线 免费| 久99久视频精品免费| 成人国产一区最新在线观看| 久久久国产成人精品二区| 国产一区在线观看成人免费| 日本三级黄在线观看| 国产一卡二卡三卡精品| 国产精品电影一区二区三区| 极品教师在线免费播放| 成人国产综合亚洲| 俺也久久电影网| 麻豆久久精品国产亚洲av| 别揉我奶头~嗯~啊~动态视频| 亚洲 国产 在线| 夜夜夜夜夜久久久久| 美女免费视频网站| 级片在线观看| 免费高清视频大片| 亚洲国产欧美网| 欧美激情高清一区二区三区| 精品福利观看| 国产av又大| 嫩草影视91久久| 欧美黄色淫秽网站| 一区二区日韩欧美中文字幕| 九色国产91popny在线| 变态另类丝袜制服| 久久精品亚洲精品国产色婷小说| 国产精品 国内视频| 日韩中文字幕欧美一区二区| 黄色片一级片一级黄色片| 91成人精品电影| 成人亚洲精品av一区二区| 一进一出好大好爽视频| 丁香六月欧美| 久久中文字幕一级| 一级a爱视频在线免费观看| 俺也久久电影网| ponron亚洲| 国产区一区二久久| 国产主播在线观看一区二区| 国内精品久久久久精免费| 淫秽高清视频在线观看| 色老头精品视频在线观看| 丝袜人妻中文字幕| 999久久久国产精品视频| 欧美黄色淫秽网站| 久久草成人影院| 亚洲国产看品久久| 人人澡人人妻人| videosex国产| 欧美不卡视频在线免费观看 | 国产精品永久免费网站| 啦啦啦 在线观看视频| 国产亚洲精品综合一区在线观看 | 99热这里只有精品一区 | 久久久久久人人人人人| 国产精品亚洲av一区麻豆| 欧美黑人精品巨大| 日本一本二区三区精品| 亚洲狠狠婷婷综合久久图片| 国产黄片美女视频| 别揉我奶头~嗯~啊~动态视频| 2021天堂中文幕一二区在线观 | 十八禁网站免费在线| 国产99久久九九免费精品| 国产精品av久久久久免费| 亚洲色图av天堂| 一本一本综合久久| 亚洲美女黄片视频| 一本精品99久久精品77| 91成年电影在线观看| 国产免费男女视频| 大香蕉久久成人网| 男人舔奶头视频| 午夜福利成人在线免费观看| 中文字幕人妻丝袜一区二区| av电影中文网址| 久久天躁狠狠躁夜夜2o2o| 一区二区三区高清视频在线| 久久久久国产一级毛片高清牌| 国产91精品成人一区二区三区| 免费一级毛片在线播放高清视频| 亚洲一码二码三码区别大吗| 精品国产亚洲在线| 十分钟在线观看高清视频www| 久久99热这里只有精品18| 夜夜躁狠狠躁天天躁| 国内毛片毛片毛片毛片毛片| 国产视频一区二区在线看| 精品熟女少妇八av免费久了| 日韩 欧美 亚洲 中文字幕| 精品久久久久久久久久免费视频| 亚洲九九香蕉| 国产精品亚洲一级av第二区| 很黄的视频免费| 男人舔女人下体高潮全视频| 亚洲 欧美一区二区三区| 搡老妇女老女人老熟妇| 精品一区二区三区视频在线观看免费| 最新在线观看一区二区三区| 国产欧美日韩一区二区三| 久久国产亚洲av麻豆专区| 99国产精品一区二区蜜桃av| 12—13女人毛片做爰片一| 中出人妻视频一区二区| 亚洲国产欧洲综合997久久, | 桃红色精品国产亚洲av| 人人妻人人澡欧美一区二区| 一本精品99久久精品77| 欧美性猛交╳xxx乱大交人| 午夜激情av网站| 欧美日韩福利视频一区二区| 日韩精品免费视频一区二区三区| 中文字幕av电影在线播放| 亚洲av熟女| 每晚都被弄得嗷嗷叫到高潮| 久久久久久亚洲精品国产蜜桃av| 欧美激情 高清一区二区三区| 99久久99久久久精品蜜桃| 久久精品91无色码中文字幕| 神马国产精品三级电影在线观看 | 精品少妇一区二区三区视频日本电影| 精品无人区乱码1区二区| 久久婷婷人人爽人人干人人爱| 国产1区2区3区精品| 亚洲一码二码三码区别大吗| 久久久久久九九精品二区国产 | 黄色成人免费大全| 很黄的视频免费| 他把我摸到了高潮在线观看| 9191精品国产免费久久| 日韩大码丰满熟妇| 91成人精品电影| 黑人欧美特级aaaaaa片| 男女之事视频高清在线观看| 丝袜在线中文字幕| 熟女少妇亚洲综合色aaa.| 亚洲精品国产精品久久久不卡| 老熟妇乱子伦视频在线观看| 无人区码免费观看不卡| 男女做爰动态图高潮gif福利片| 亚洲中文日韩欧美视频| 在线观看午夜福利视频| 亚洲美女黄片视频| 高潮久久久久久久久久久不卡| 久久精品国产亚洲av高清一级| 黄色 视频免费看| 欧美一级毛片孕妇| 国产一区二区在线av高清观看| 欧美日韩精品网址| 老司机午夜十八禁免费视频| 18禁国产床啪视频网站| 熟妇人妻久久中文字幕3abv| 欧美成狂野欧美在线观看| 美女免费视频网站| 日日爽夜夜爽网站| 午夜福利在线观看吧| 午夜免费成人在线视频| 精华霜和精华液先用哪个| 国产成人欧美在线观看| 长腿黑丝高跟| 女性被躁到高潮视频| 国产极品粉嫩免费观看在线| 国产免费av片在线观看野外av| 久久精品国产综合久久久| 午夜福利视频1000在线观看| 美女免费视频网站| 日日爽夜夜爽网站| 在线观看午夜福利视频| 亚洲自拍偷在线| 黄片播放在线免费| 大型av网站在线播放| 成人国产一区最新在线观看| 91大片在线观看| 男女之事视频高清在线观看| 老熟妇仑乱视频hdxx| 在线播放国产精品三级| 91av网站免费观看| 久久久久久人人人人人| 国内久久婷婷六月综合欲色啪| 极品教师在线免费播放| 身体一侧抽搐| 成人亚洲精品av一区二区| 午夜福利免费观看在线| 欧美三级亚洲精品| 一卡2卡三卡四卡精品乱码亚洲| 琪琪午夜伦伦电影理论片6080| 国产精品亚洲一级av第二区| 狂野欧美激情性xxxx| 美女高潮到喷水免费观看| 在线观看免费视频日本深夜| 最新在线观看一区二区三区| 99在线人妻在线中文字幕| 一级a爱视频在线免费观看| xxxwww97欧美| 免费高清视频大片| 亚洲专区国产一区二区| 国产亚洲欧美98| 哪里可以看免费的av片| 变态另类成人亚洲欧美熟女| 性欧美人与动物交配| 女生性感内裤真人,穿戴方法视频| 一级a爱视频在线免费观看| 久久久国产成人精品二区| 女生性感内裤真人,穿戴方法视频| 女同久久另类99精品国产91| 国产v大片淫在线免费观看| 亚洲无线在线观看| 999久久久精品免费观看国产| 99热这里只有精品一区 | 精品久久久久久,|