• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    In-situ observation of twinning and detwinning in AZ31 alloy

    2023-01-08 10:22:06WuGongRuixioZhengStefnusHrjoTkuroKwskiKzuyAizw
    Journal of Magnesium and Alloys 2022年12期

    Wu Gong,Ruixio Zheng,Stefnus Hrjo,Tkuro Kwski,Kzuy Aizw,

    Nobuhiro Tsujib,c

    a J-PARC Center,Japan Atomic Energy Agency,2-4 Shirane Shirakata,Tokai,Naka,Ibaraki 319-1195,Japan

    b Center for Elements Strategy Initiative for Structural Materials,Kyoto University,Yoshidahonmachi,Sakyo-ku,Kyoto 606-8501,Japan

    c Department of Materials Science and Engineering,Kyoto University,Yoshida-honmachi,Sakyo-ku,Kyoto 606-8501,Japan

    d School of Materials Science and Engineering,Beihang University,Beijing 100191,China

    Abstract Twinning and detwinning behavior of a commercial AZ31 magnesium alloy during cyclic compression-tension deformation with a total strain amplitude of 4%(±2%)was evaluated using the complementary techniques of in-situ neutron diffraction,identical area electron backscatter diffraction,and transmission electron microscopy.In-situ neutron diffraction demonstrates that the compressive deformation was dominated by twin nucleation,twin growth,and basal slip,while detwinning dominated the unloading of compressive stresses and subsequent tension stage.With increasing number of cycles from one to eight:the volume fraction of twins at-2% strain gradually increased from 26.3% to 43.5%;the residual twins were present after 2% tension stage and their volume fraction increased from zero to 3.7% as well as a significan increase in their number;and the twinning spread from coarse grains to fin grains involving more grains for twinning.The increase in volume fraction and number of residual twins led to a transition from twin nucleation to twin growth,resulting in a decrease in yield strength of compression deformation with increasing cycles.A large number of<c>-component dislocations observed in twins and the detwinned regions were attributed to the dislocation transmutation during the twinning and detwinning.The accumulation of barriers including twin boundaries and various types of dislocations enhanced the interactions of migrating twin boundary with these barriers during twinning and detwinning,which is considered to be the origin for increasing the work hardening rate in cyclic deformation of the AZ31 alloy.? 2022 Chongqing University.Publishing services provided by Elsevier B.V.on behalf of KeAi Communications Co.Ltd.This is an open access article under the CC BY-NC-ND license(http://creativecommons.org/licenses/by-nc-nd/4.0/)Peer review under responsibility of Chongqing University

    Keywords:Magnesium;Neutron diffraction;Twinning;Detwinning;Dislocation transmutation.

    1.Introduction

    Basal slip and{10ˉ12}twinning are well known to be the basic deformation modes in magnesium(Mg)and its alloys.Basal slip is the principal deformation mode,however,it cannot accommodate the strain along thec-axis.{10ˉ12}twinning,the so-called tension twinning or extension twinning,whose critical resolved shear stress(CRSS)is slightly higher than the basal slip[1,2],can accommodate the tensile strains along thec-axis.Therefore,{10ˉ12}twinning is considered to be a key factor in improving the ductility of Mg alloys[1-3].{10ˉ12}twinning can be readily activated in the grains subjected to a tensile stress parallel to thec-axis[3]or a compressive stress perpendicular to thec-axis[3,4],but is absent in the opposite stress state.This polar feature of deformation twinning is the reason for the high plastic anisotropy in Mg and its alloys,especially in wrought conditions because of the texture[3-8].Another important feature of{10ˉ12}twinning is its reversibility,in which the orientation of deformation twins can revert to the initial orientation by reversing the applied stress[4,8-12]or even a reversal of internal stress during unloading[13-15],which is known as detwinning(or untwinning).Because of the reversible feature,twinning and detwinning have been confirme as the main plastic deformation modes in a variety of Mg alloys including pure Mg[8],Mg-7.7Al(at.%)[14],AZ31[4,9,12],ZK60[10,11],and AZ91[8],when the specimens were subjected to alternate loading conditions,such as cyclic deformations with compression-tension[4,9-11],tension-compression[4],or loading-unloading[13-15].

    In general,work hardening in plastic deformation of structural metallic materials is caused by the interactions between plastic deformation and barriers such as grain boundary[16-20],dislocations[21,22],and second-phase particles[14].Moreover,plastic deformation generally introduces various barriers in the microstructure,including dislocations,phase boundaries(i.e.,transformation-induced plasticity[23]),and twinning boundaries(TBs)[18,24-26],which are important strengthening mechanisms in the development of structural metallic materials.It has been reported that the TBs as the coherent boundaries with low excess energies contribute strength through interaction with dislocation motion and increase ductility through creating local sites for nucleating and accommodating dislocations[18,24,26].The TBs in Mg alloys are movable through twin growth or twin shrinkage,i.e.,detwinning[8,25].The pinning effect of TBs by the segregation of solute atoms can increase the strength of Mg alloys[25].Similarly,the motion of TBs can be suppressed by dislocations introduced by pre-strains,leading to changes in morphology of twins and the stress-strain response[27-30].Actually,dislocations are allowed to penetrate the TBs[2,31-34].Therefore,the interactions between dislocations and TBs,and the feature of dislocations after penetration of TBs are a concern for the mechanical properties.A dislocation transmutation has been reported in interactions between dislocations and TBs based on the experimental evidence,where the dislocations with Burgers vector of<a>were found to transmute into<a>or<c+a>after penetration of TBs[33,35].More recently,I1stacking faults,lying on the basal planes of twins,have been observed,and were considered to be associated with the glissile-to-sessile transition during twinning[36,37].The reaction between dislocations and TBs would establish a basis for work hardening during twinning deformation[38].Moreover,the hardening of twins by the increase in dislocation multiplicity(i.e.,dislocation type)within twins was reported through simulations by Kadiri and Opeddal[31]and Oppedal et al.[32].These studies mainly focused on the interaction between dislocations and motion of TBs during twinning,whereas in the detwinning process the effect of these interactions on the mechanical properties are still far from being understood.Therefore,to track the evolutions of twins and dislocation structures during cyclic deformation in Mg alloys is crucial for understanding the mechanical properties.

    Because of the unique crystallographic feature,twinning and detwinning behavior matches well with the information provided by diffraction techniques,such as electron backscatter diffraction(EBSD)and neutron diffraction(ND).Both techniques have their respective advantages.In-situND provides the bulk averaged crystallographic information such as volume fraction of twins[10,13,14,39]and lattice strain[11,13,14,39,40]for interpretation of macroscopic deformation behavior.Conversely,EBSD provides information focusing on local details such as area fraction of twins[8,12,27-29],morphology[12,27,27-29],variant selection[8,12,41],and crystallographic features of various boundaries[8,41,42].The obtained EBSD results can be used to interpret the work hardening behavior with respect to grain size dependence[12],orientation dependence[43],and boundary feature dependence[8,41]of twinning.Although great efforts have been made on the deformation mechanisms of low cycle fatigue properties in Mg and alloys,the relationship between the deformation mechanisms and the mechanical responses is yet to be fully understood.

    In the present study,the deformation mechanisms with respect to twinning,detwinning,and their interaction with dislocations during compression-tension cyclic deformation in a commercial AZ31 Mg alloy were evaluated systematically using a combination ofin-situND,identical area EBSD,and transmission electron microscopy(TEM)techniques.The mechanical responses in compression-tension cyclic deformation are discussed with bulk averaged twin volume fraction(TVF),the local details of twinned microstructure,and the dislocation structures.

    2.Experimental methods

    2.1.In-situ neutron diffraction

    Commercial AZ31 alloy(Mg-3 wt.%Al-1 wt.%Zn)extruded rods with a diameter of 52 mm were used in this study.The rods were extruded at 623 K with an extrusion ratio of 9.Cylindrical tensile specimens with a gage diameter of 6 mm and a length of 17 mm were cut from the as-extruded rod forin-situND experiment.The loading direction was parallel to the extrusion direction(ED).TheinsituND experiment during deformation was performed using a time-of-fligh(TOF)engineering neutron diffractometer“TAKUMI”at the Japan Proton Accelerator Research Complex(J-PARC)Fig.1a shows the geometrical arrangement of thein-situND experiment.The specimen was set up on the loading frame horizontally,with its loading axis angled-45° relative to the incident neutron beam.TAKUMI has two detector banks,south bank and north bank,positioned at+90° and-90° relative to the incident beam.As a result,the diffraction vectors observed by the south and north banks were parallel to the loading direction(hereafter,labeled as LD//)and perpendicular to the loading direction(hereafter,labeled as LD⊥),respectively.The incident beam was set as 5 mm in width and 5 mm in height.A combination of the incident beam size and 5 mm-width radial collimators placed in front of the detector banks define that a 5 mm cubic located at the gage center of the specimen was measured.The neutron wavelength range of 0.094-0.471 nm(i.e.,d-range of 0.067-0.333 nm)was selected for the present experiment.Details of the diffractometer have been described elsewhere[44].

    Fig.1.Multiscale experimental methods.(a)Diffraction geometry of the in-situ neutron diffraction experimental arrangements,(b)sequence of the cyclic compression-tension deformation applied to the AZ31 alloy.Ci and Ti represent the compression and tension steps of the ith cycle,and(c)schematic showing the dog-bone-shaped specimen for electron backscatter diffraction analysis cut from prestrained cylindrical tensile specimens(For interpretation of the references to color in this figure the reader is referred to the web version of this article).

    Fully reversed strain-controlled cyclic compression-tension deformation with a total strain amplitude of 4%(±2%)at a strain rate of 2×10-5s-1was applied to the cylindrical tensile specimens.All steps of the cyclic deformation were conducted with strain control through the strain gage attached to the specimen.The KFEM series strain gages(Kyowa Electronic Instruments Co.Ltd.)having a strain limit of 20%were used Fig.1.b shows the sequence of cyclic deformation.After each unloading step,an interruption of 10 min was set for collecting more statistics of diffraction profile Eight cycles were performed for thein-situND experiment.After theinsituND experiment,an additional compression to-2% strain was performed on the specimen as to be the initial condition for the identical area EBSD observation.As marked in Fig.1b,hereafter,the compression and tension steps of theith cycle are denoted asCiandTi,respectively.

    Diffraction profile were analyzed using the Z-Rietveld code to obtain integrated intensities of selected diffraction reflection via a single-peak fittin procedure[45].Evolution of the TVF was analyzed using the Material Analysis Using Diffraction program[46]combined with the MTEX program[47];the details are described elsewhere[39].

    2.2.Identical area electron backscatter diffraction observation

    Two cylindrical tensile specimens,Sample 1andSample2(marked as red dots in Fig.1b),were prepared according to the following procedures.Sample 1was compressed to-2% strain from the initial condition(i.e.,C1),andSample 2was compressed to-2% strain after eight cycles of compression-tension with±2%(i.e.,C9).As illustrated in Fig.1c,a small dog-bone-shaped specimen with a gage length of 2 mm and a gage cross section of 1×0.5 mm was cut from the prestrained specimen for EBSD analyses.The specimens for EBSD analysis were mechanically polished using a fin grade sandpaper followed by a fina polish using a colloidal silica suspension(OP-S,Struers).The microstructures were characterized using a TSL EBSD system equipped on a JEOL JSM-7100F scanning electron microscope(SEM).The EBSD analyses at the identical areas were performed on samples after providing step-by-step tension to various strains.Tensile tests were conducted using a Shimadzu tensile testing machine at ambient temperature outside of SEM equipment.The EBSD data were postprocessed using the commercial TSL OIM analysis software.

    Fig.2.Initial microstructure.(a)Inverse pole figur(IPF)map of the cross section of the extruded AZ31 magnesium alloy,(b)corresponding IPF showing initial basal texture(standard stereographic triangle showing extrusion direction),and(c)related bimodal grain size distribution.The initial diffraction profile of(d)axial(extrusion)and(e)radial directions.

    2.3.Transmission electron microscopy measurement

    The foil specimens for TEM observation were cut from the aforementioned cylindrical tensile specimen along the longitudinal section.TEM specimens were prepared by mechanical grinding,followed by twin-jet electropolishing.TEM characterization of microstructure was conducted using a JEOL JEM-2010 and was operated at 200 kV.

    3.Result s

    3.1.Initial microstructure characteristics

    The microstructure characteristics of the as-received extruded AZ31 alloy sample(denoted bySample 0)are shown in Fig.2.The inverse pole figur(IPF)map in Fig.2a was observed on the longitudinal section of the extruded rod,in which the colors correspond to the crystallographic orientations parallel to the ED.The IPF map and IPF(Fig.2b)of the ED demonstrate a typical basal texture generated by extrusion,i.e.,c-axes perpendicular to the ED[8,9,12,48].As shown in the grain size distribution chart in Fig.2c,the IPF map shows a twin-free and bimodal grain structure,which consists of fin and coarse equiaxed grains with average grain size of 11.7μm and 40.2μm,respectively.The average grain size of all grains is approximately 18μm.Bimodal microstructures consisting of fin and relatively coarse DRXed grains have been frequently observed in magnesium alloys subjected to extrusion at relatively low temperatures[49,50],which are related to the pinning of grain boundary by precipitates and also the sequence of precipitation and recrystallization[51].The extrusion parameters of the present material may be in the critical region for forming the bimodal grain structure.

    The ND profile of the initial condition in LD//(Fig.2d)and LD⊥(Fig.2e)exhibit different intensities.The{hkil}lattice planes close to the basal plane such as{0002},{10ˉ12},and{10ˉ13}were absent in the LD//diffraction pattern,whereas they were intense in the LD⊥pattern.The ND patterns show an initial texture consistent with that obtained by the EBSD analysis.

    Fig.3.Twinning and detwinning behavior during cyclic deformation tracked using in-situ neutron diffraction(ND).Evolution of ND profile along an axial direction corresponding to the cyclic compression-tension test,which shows alternate changes of diffraction reflections Change in macroscopic strain was superimposed for reference.

    Fig.4.(a)Detailed changes of the macroscopic strain,diffraction profiles and integrated intensity of the 0002 diffraction reflectio along the axial direction in cycle 1 showing the twinning and detwinning behavior directly and(b)evolutions of the integrated intensities of representative hkil diffraction reflection along the axial direction during cycle compression-tension deformation.

    3.2.Twinning and detwinning behavior tracked by in-situ neutron diffraction

    Using a pulsed neutron source and the TOF diffraction method,a wide range of wavelengths can be used to detect various{hkil}lattice planes simultaneously Fig.3 shows the evolution of the ND patterns along LD//corresponding to the cyclic compression-tension test.Note that several lines at around 17,25,and 41 ks showing no intensity were caused by the accidental stop of beam.As mentioned above,initial extrusion texture led to the absence of Bragg reflection such as{0002},{10ˉ13},and{10ˉ14}before deformation.In the subsequent deformation,the evolution of the diffraction pattern shows alternate increase and decrease in the aforementioned absent Bragg reflection corresponding to the cyclic loading.

    Fig.4a demonstrates the detailed changes of the diffraction patterns in cycle 1.The intensities of the{100}reflec tion decreased accompanied with an increase in the{0002}reflectio in compression,while the tendency changed conversely during unloading after compression and in the subsequent tensile deformation.It coincides with the lattice reorientation by{10ˉ12}twinning and detwinning in Mg and its alloys[10,11,13].Under the present initial texture,compressive loading parallel to ED promoted{102}twinning but was unfavorable for basal slip.In subsequent tension after compression,tensile stress applied on thec-axis of twins favored the activation of detwinning.A slight decrease in the integrated intensity of the{0002}reflectio also appeared during unloading after compression,which shows the occurrence of detwinning(see bottom graph in Fig.4a).The intergranular stress was considered as the origin of detwinning[11,13].

    Evolutions of the integrated intensity of representative{hkil}Bragg reflection along LD//are compared in Fig.4b.The grains with{10ˉ10}and{110}Bragg reflection whose integrated intensities decreased during twinning and partially reversed during detwinning,were define as“matrix.”In contrast,the grains with{0002}Bragg reflectio(together with{10ˉ13}and{10ˉ14}Bragg reflections that exhibited the opposite tendency of integrated intensity change were define as“twins.”The integrated intensity for grains with{101}Bragg reflectio showed less variation,which shows that twinning was unfavorable in them,but is known to be dominated by basal slip[11,13].

    The axial distribution function(ADF)of the basal pole has been proved to be reliable for determining the TVF in Mg alloys having axisymmetric texture[7,39,48,52].The ADF of the basal pole at unloading conditions of each step is plotted in Fig.5a.The 0° and 90° of the horizontal axis represent that thec-axes of the grains are parallel and perpendicular to the loading direction,respectively.As seen,the intensity of the basal pole distributed around 0° after compression is evidently higher than that after tension,and gradually increases with cycle number.This coincides with the texture changes caused by the twinning in the compression deformation and the detwinning in the tensile deformation.Assuming that extension twinning is the only origin for texture changes,the TVF can be calculated from the variation of the ADF of the basal pole using the following equation[52]:

    whereχis the tilt angle between thec-axis and the compression direction,I(χ)is the intensity at angleχ,andI0(χ)is the initial intensity of the twin-free condition.In the previous study,45° and 57° were selected as the dividing points for separating the matrix and the twin orientations[48,52].These dividing points may differ depending on the chemical composition and the initial texture.In the present study,50°was selected as the dividing point according to which I(50°)remains constant throughout the deformation(Fig.5a).

    Fig.5.(a)Axial distributions of basal poles in the sample subjected to various deformation cycles and(b)Evolution of twin volume fraction during cyclic deformation evaluated using in-situ neutron diffraction.

    Fig.5b shows that TVF evaluated from the ADF of the basal pole,and it increased with the compressive strain.Moreover,the TVF at the largest value of compressive strain(-2%)increased with the increase in cycle number.It was observed that the TVF of 26.3% at the firs cycle increased to 43.5% at the eighth cycle.In tension,the TVF increment caused by twinning during compression was almost removed but partly remained although the tensile deformation reached the largest strain value(+2%).This indicates the presence of residual twins.Similar to the trend in TVF,the volume fraction of residual twins after each tension step increased with increasing number of cycles;that is,almost zero at the firs cycle increased to 3.7% at the eighth cycle.

    3.3.Detwinning behavior tracked by identical area electron backscatter diffraction

    The evolutions of TVF and volume fraction of residual twins during cyclic deformation were quantitatively evaluated byin-situND,and their trends are in agreement with the qualitative results in rolled AZ31B Mg alloy[4]and extruded ZK60A[10].The morphological details of the twins in previous studies,however,are insufficient

    Here,the identical area EBSD analysis was performed onSample 1andSample 2to investigate how twins introduced by different deformation histories evolve when a tensile loading is applied Fig.6a1 and b1 shows the positions in the stressstrain curves where the EBSD analses were carried out,and Fig.6a2-a5 and b2-b5 shows the corresponding twin maps,where the twins were highlighted in red.Before tension deformation,Sample 1exhibited lower area fractions of twins(16.0%)than that ofSample 2(47.5%).Moreover,the number percentage of the grains containing twins was 20% forSample 1and 44% forSample 2,indicating that not only the twin fraction increased,but also additional grains were involved in twinning with increasing cycles.In the subsequent step-bystep tension,the twins gradually shrank with tensile strain in both samples Fig.7a shows the misorientation angle distributions along the yellow lines(A-A′)in Fig.6a2-a5.The misorientation angles of the TBs are close to 86.3°.As the deformation progresses,the twins become narrower.Basically,the narrowing of each twin was realized by the movement of one-sided TB.This needs to be verifie by further studies.

    Fig.6.Detwinning behavior during tensile deformation tracked by identical area electron backscatter diffraction analysis.(a1)Measurement positions on the stress-strain curve of the a2-a5 in Sample 1(-2% strained),(a2-a5)twin maps showing the microstructure evolution due to detwinning in Sample 1,(b1)measurement positions on the stress-strain curve of the b2-b5 in Sample 2(-2% strained after eight cycles of deformation),and(b2-b5)twin maps showing the microstructure evolution due to detwinning in Sample 2.Twins are highlighted in red(For interpretation of the references to color in this figur legend,the reader is referred to the web version of this article).

    Fig.7b shows a comparison of area fractions of the twins obtained using EBSD analyses with TVF evaluated byinsituND.There are some differences,which may be related to the relatively small statistical area of the EBSD analysis.Nevertheless,it can be seen that the area fraction of twins dropped from 16.0% to 1.4% inSample 1and 47.5% to 5.8%inSample 2by tension.The EBSD results also confirme the presence of residual twins similar to that evaluated usinginsituND.

    Despite the inhomogeneity of grain size,the texture was homogeneous in the whole sample.The average Schmid factors for{102}twinning calculated by TSL OIM software are 0.444 and 0.451 for fin and coarse grains,respectively,suggesting the equivalent favorability for twinning in crystallographic aspect Fig.7c shows the different evolution in the area fraction of twins between coarse and fin grains.The twins were mainly observed in the coarse grains inSample 1andSample 2,indicating that twinning prefers to occur in the coarse grains rather than in the fin grains.This confirm the finding of many studies on the grain size dependence of deformation twinning[12,19,20,53,54].InSample 2,additional fin grains were also involved in twinning,suggesting that cyclic compressive-tensile deformation promoted the twinning activity in fin grains Fig.7d shows that the decrement rates of the area fraction of twins in coarse and fin grains were almost similar with each other in the same sample.As we know,twinning can generally be divided into two steps,namely,twin initiation and twin growth through moving TBs.Detwinning is similar to the process of grain growth,but the TBs move in the opposite direction to shrink the twins[42,55].The EBSD results indicate that twinning had a grain size effect,while detwinning exhibited a weak sensitivity to the grain size.It may be understood that the grain size has a significan effect on twin initiation but hardly affects the movement of TBs,because the latter occurs inside the grains and results in less interaction with grain boundaries.

    Fig.7.(a)Profile present misorientation angles relative to the orientations along A-A′lines in Fig.6a2-a5 showing the motion of twin boundaries due to detwinning,(b)comparison of area fraction of twins with volume fraction of twins evaluated using electron backscatter diffraction and neutron diffraction,respectively.Comparison of(c)evolution of area fraction of twins and(d)corresponding decrement caused by tensile deformation between coarse and f ne grains.The coarse grains(highlight)and fin grains(without highlight)of Sample 1 and Sample 2 for evaluation are shown in the inset of(c)and(d).

    Fig.8.Comparison of grain size distributions of residual twins between Sample 1 and Sample 2 after tension.

    Fig.8 shows the number of residual twins as a function of their equivalent grain diameter inSample 1andSample 2after tension.As the number of cycles increased fromT1toT9,the equivalent grain diameter of the residual twins became slightly coarser(average grain size:0.7μm→1.0μm)and the number density(number/indexed area)of residual twins increased significantl(1.60×104mm-2→3.15×104mm-2).

    Fig.9 presents the boundary maps and Kernel average misorientation(KAM)maps to express the changes in boundary density and dislocation density with cyclic deformation,respectively.The boundary maps ofSample 1andSample 2,including low angle grain boundaries(LAGBs:2°~15°),high angle grain boundaries(HAGBs:>15°),and{10ˉ12}twin boundaries(TBs:86.3°±5°)combined with the{10ˉ12}twins highlighted in red,are shown in Fig.9a and b,respectively.Considerably more TBs inSample 2thanSample 1can be observed.The LAGBs mainly distributed in twins(see inset of Fig.9b)similar to the previous study[8,30].The quantitative comparison of various boundaries was expressed by boundary density(length of boundary/indexed area)in Fig.9c.The sample before deformation(i.e.,Sample 0)was added for reference.As seen,the boundary densities of all boundaries(LAGBs+HAGBs)are 350 mm-1,861 mm-1,and 1205 mm-1forSample 0,Sample 1,andSample 3,showing a remarkably increasing tendency with increasing number of cycles.The increment in boundary density of all the boundaries is mainly contributed by those of TBs(0 mm-1→345 mm-1→509 mm-1)and LAGBs(80 mm-1→164 mm-1→305 mm-1).Interestingly,the HAGBs with excluding the TBs also exhibited a slight increase with increasing cycles,which may be contributed by the twin-twin boundaries or LAGBs to HAGBs transition Fig.9d and e show the KAM maps ofSample 1andSample 2,respectively.The KAM value,as a parameter representing the dislocation density,is obviously higher inSample 2than that ofSample 1.The average KAM values of matrix and twins were separated and compared in Fig.9f.The KAM value of matrix increased slightly(0.5 °→0.55 °)aftera-2% compressive strain,and then increased to 0.79 ° inSample 2.The KAM values of twins exhibited a similar tendency to that of matrix,but were consistently higher than the latter.In brief,the cyclic deformation introduced various barriers including TBs,LAGBs,and dislocations in matrix and twins.Combined with the volume fraction and number density of residual twins described above,these microstructure parameters are crucial to influenc the mechanical responses.

    Fig.9.Grain boundaries on image quality maps of(a)Sample 1 and(b)Sample 2 showing low angle grain boundaries(LAGBs),high angle grain boundaries(HAGBs),and{10ˉ12}twin boundaries(TBs:86.3°±5°),and(c)the corresponding changes in boundary density after different cycles(S0,S1,and S2 refer to Sample 0,Sample 1,and Sample 2).The inset in(b)enlarged the frame area to show the distribution of LAGBs.KAM maps of(d)Sample 1 and(e)Sample 2,and(c)the corresponding changes in average KAM value of matrix and twins after different cycles(For interpretation of the references to color in this figure the reader is referred to the web version of this article).

    3.4.Mechanical responses in cyclic deformation

    The stress-strain curves of the cyclic compressive-tensile deformation shown in Fig.10a demonstrate a strong asymmetry between compression and tension,which is quite similar to those typically found in wrought Mg alloys[4,10].In the firs compression stage,there was a plateau with weak work hardening after yielding.Such a plateau is a typical mechanical response when{102}twinning is dominant in textured Mg alloys[13,48].The plateau was caused by the avalanche-like formation of twinning[13].A pseudo-elastic behavior that appeared during unloading after compression is frequently associated with the detwinning driven by the intergranular stress[11,13].In the subsequent tensile deformation,the stress-strain relationship shows a curved shape that continues from the unloading after compression without a linear elastic region.It can be considered that the occurrence of detwinning accommodating strain resulted in the absence of an elastic region in the tension stage.When the absolute strain in tension exceeded zero strain,an inflectio point that was followed with a work hardening stage appeared.This inflec tion point is considered to be a transition from detwinning dominant deformation to dislocation slip dominant deformation.Note that there are some stress drops in the stress-strain curves,which are the products of strain gage control method.Because when the twins formed at the surface where the strain gage attached,a sudden increase in strain led to a rapid decrease in crosshead speed,and then resulted in a stress drop in stress strain curve.

    Fig.10.Stress-strain curves in cyclic deformation.(a)Engineering stress-strain curves of cyclic deformation showing a strong asymmetry between compression and tension,(b)stress-strain curves of compression,and(c)stress-strain curves of tension.

    For simplicity,the stress-strain curves were separated into a compressive stress part in Fig.10b and a tensile stress part in Fig.10c.In Fig.10b and c,stress and strain values of compression curves were plotted in positive values,and the strain values at unloaded conditions were shifted to zero.With increasing the loading cycles,the stress-strain curves in compression and tension evolved as follows:

    ?In compression,the yield strength define by the deviation from the linear elastic response decreased gradually,but in the following plastic deformation,the work hardening rate increased gradually,resulting in an increase in the absolute peak stress at the largest compressive strain.

    ?In tension,the stress increased at the beginning of deformation,but the inflectio point of the slope of the work hardening gradually shifted to a high strain level,resulting in a decrease in the peak stress at the largest tensile strain.

    3.5.Interaction between dislocations and twin boundaries

    In the present study,plastic deformation was dominated by twinning and detwinning through the motions of TBs,and accommodated partly by dislocation movement.Therefore,the interactions between dislocation and TBs may play a crucial role in controlling the plastic deformation behavior.In this section,special attention was focused on the interactions between the dislocations and the TBs,and the relevant results obtained by TEM analysis were summarized.

    Sample 1with abundant{10ˉ12}twins introduced bya-2%compressive strain was selected for TEM analysis Fig.11a shows the microstructure of a typical grain containing a deformation twin.The compression direction(i.e.,the ED)is almost parallel to the horizontal direction.According to the selected area electron diffraction(SAED)patterns(Fig.11bd),the matrix,twinned,and detwinned regions were determined and labeled in Fig.11a.The SAED patterns in Fig.11b and c show that the matrix and twins share the common zone axis(ZA)of<110>but theirc-axes are oriented approximately perpendicular to each other.An accurate crystallographic orientation relationship between matrix and twin was determined from the SAED pattern obtained at the matrix/twin interface(Fig.11d).The matrix and twins shared a common ZA<110>,a common{102}(i.e.,the twin plane),and a deviation of 86.3° between theirc-axes.The crystallographic orientation relationship is consistent with the classic{10ˉ12}twin mode(Fig.11e),although recent studies have reported that the basal planes of the matrix and twin have a perpendicular relationship in a single crystal of Mg[56].

    Under the diffraction condition that ZA is parallel to<110>of both matrix and twin as illustrated by Fig.11e,abundant straight dislocations are visible in both matrix and twin(Fig.11a).Most of the dislocations are aligned parallel to the basal planes in both the matrix and twin;therefore,they are likely to be the basal dislocations.

    Fig.11.(a)Transmission electron microscopy image showing straight dislocations within the matrix and the twin parallel to basal plane traces.SAED patterns of(b)matrix,(c)twin,and(d)both the matrix and the twin on<11ˉ20>ZA.(e)Schematic illustration showing orientation relationship of{10ˉ12}twinning.(f)Schematic illustration showing dislocation distributions in the matrix,twin,and the detwinned region.TB1 and TB2 mean the twin boundaries.

    Because the incident beam was parallel to the twin plane,the matrix/twin interface should be narrow under this observation condition.As can be seen,only the lower left side of the interface(see TB1 in Fig.11a)was observed clearly,but a dark band exists between the twin and matrix on the higher right side of the interface(near TB2 in Fig.11a).By comparing the SAED patterns between the dark band region and the adjacent matrix,it was found that they had almost the same orientation with a misorientation angle of approximately 1.5°As mentioned above,detwinning already started during unloading in compression.The dark band is considered as the detwinned region,and a similar morphology of the detwinned region was also observed using EBSD(Fig.6).The dislocations in the detwinned region are highly dense and have a straight shape being parallel to the basal plane of the matrix.According to the results shown in Fig.11a and a schematic drawn in Fig.11f,the dislocations in the matrix,twinned,and detwinned regions show differences in orientation and density.

    The well-known“g?b=0′′invisibility criterion(wheregandbare the diffraction vector and the Burgers vector,respectively)was used to distinguish the types of dislocations Fig.12a shows a TEM image when the specimen was tilted to a two-beam condition withg=0002 reflectio of the matrix.Under this diffraction condition,the<a>dislocations withb=1/3<110>are invisible.In contrast,the dislocations with<c>-component in the Burgers vector have good contrast for this condition.As can be seen,the matrix part is blank,suggesting that the dislocations in the matrix observed in Fig.11a are<a>dislocations.Interestingly,abundant dislocations are visible in the detwinned region,indicating that these dislocations have a<c>-component in the Burgers vector.In the same way,a strong diffraction contrast from the<c>-component can be observed in the twinned region underg=0002 reflectio in twins(Fig.12b).

    4.Discussion

    4.1.Formation of<c>-component dislocations during twinning and detwinning

    <c>-component dislocations in Mg alloys are generated base on two independent mechanisms.One is pyramidal slip[5,57,58]and the other is dislocation transmutation.The socalled dislocation transmutation during twinning was reported in various HCP metals such as Mg and Zr[31-33,35,59].When the<a>dislocations introduced by a basal slip or prismatic slip in the matrix of Mg or Zr penetrate to the{10ˉ12}TBs,the Burgers vector of<a>in the matrix will be transformed into<c+a>or<a>in twins.Moreover,abundant stacking faults lying in the basal planes of twins have been frequently observed in various hcp metals such as Be[60],Zr[59,61],Ti[61],and Mg[36,37].Recently,these stacking faults in Mg have been determined to be the I1stacking faults formed by glissile-to-sessile transition during twinning analogous to the Basinski mechanism[36,37].Therefore,the present observed<c>-component dislocations aligned parallel to the basal planes in twins are possibly sessile partial dislocations of I1stacking faults formed by the reaction between the basal dislocations and TBs.

    Fig.12.Dislocation transmutation.(a)Bright-fiel image of the matrix with g=0002 showing dislocations having<c>-component Burgers vector in the detwinned region,(b)bright-fiel image of the twin with g=0002 showing dislocations having<c>-component Burgers vector within the twin,and(c)schematic illustration showing the generation of<c>-component Burgers vector dislocations in the detwinned region.The observation areas of(a)and(b)are the rectangles shown in Fig.11a.

    Considering that the basal plane of the matrix in Fig.11a was not completely parallel to the compression direction and then the Schmid factor for basal slip cannot be neglected.Undoubtedly,the straight<a>dislocations lying in the basal plane in the matrix were introduced by a basal slip at an early stage of compressive deformation.The dislocations in twins with<c>-component also lying in the basal plane may inherit from the<a>dislocations in the matrix through dislocation transmutation.With further compressive deformation,<a>dislocations may also be introduced in twins by basal slip[3].

    Detwinning is similar to twin growth,both of which are completed through motion of TBs but in opposite directions.Therefore,the dislocation transmutation that occurred during twinning may also occur during detwinning.When<a>dislocations were introduced in twins by basal slip during compressive deformation,these dislocations had a chance to be transmuted into<c>-component dislocations during detwinning,as that occurred during twinning.It has been reported that basal slip can be active in twins[3],and the basal slip was feasible in the twins observed in Fig.11 because its basal plane-normal were not parallel to the loading direction.In brief,the generation of<c>-component dislocations in the detwinned region can be comprehended by the illustration in Fig.12c.First,the{10ˉ12}twins formed in the matrix under the compressive deformation,then the<a>dislocations were introduced by basal slips in twins when the resolved shear stress applied on the basal plane exceeded the CRSS.In the subsequent unloading and tension stages,detwinning occurred to shrink the twins,and interactions between the dislocations in twins and the motion of TBs led to the dislocation transmutation.As a result,dislocations with<c>-component remained in the detwinned region.

    4.2.Mechanical response and microstructure evolution during cyclic deformation

    The present material has a strong extrusion texture.This condition favors extensive{10ˉ12}twinning in compressive deformation and detwinning in subsequent tensile deformation[4,10].The evolutions of twinning and detwinning play key roles during cyclic loading deformation.Here,the stressstrain curves and variations of the TVF of the second and seventh cycles were picked up as shown in Fig.13a and b for discussion.

    Fig.13.Relationship between deformation mechanisms and stress-strain behavior.Comparison of stress-strain curves and variations of the twin volume fraction between the second and seventh cycles in(a)compression and(b)tension,respectively.(c)Schematic showing the comparison of twinning and detwinning behavior in the second and seventh cycles.

    InC2,an apparent elastic region with a linear relationship between the stress and strain can be observed,but not inC7.Correspondingly,an increase in the TVF was observed from the beginning ofC7.The early yielding may be attributed to the growth of residual twins because the CRSS for twin growth is significantl lower than that for twin initiation[4,55].As illustrated in Fig.13c,the fraction of residual twins in the sample beforeC7is higher and distributed in more grains than that beforeC2,which can be predicted from the EBSD results shown in Fig.6.As has been reviewed systematically,numerous studies related to the effect of pre-strain on twinning and detwinning behavior have been conducted in recent years[62],and they concluded that the twin boundary mobility associated with mechanical properties depends on the size of twins and dislocation density in the pre-strained sample[27-29].Small twins with less dislocations introduced by a light pre-strain showed an improvement on twin boundary mobility,whereas a heavy pre-strain suppressed the motion of twin boundary significantl due to the high dislocation density[27].Here,the higher KAM value in twins than that in matrix may lead the twin shrinkage more difficul than twin growth,and then resulted in more residual twins with increasing number of cycles.The residual twins provide sufficien sites for accommodating the strain via twin growth,and thus reduces the yield strength.In the subsequent plastic compressive deformation,the increasing rates of TVF with the strain became nearly linear(Fig.13a).The higher fraction of initial residual twins and early yielding led to a higher fraction of twins at the end ofC7than that ofC2.

    The stress-strain curve indicates thatC7exhibits higher work hardening behavior than that ofC2,resulting in higher stress at the end of compression.As supported by the EBSD analysis(Fig.9),various barriers were introduced in microstructure during cyclic deformation,which are considered to be the reasons for the enhanced work hardening with increasing number of cycles as follows:

    ?The accumulation of dislocations in matrix and twins;

    ?An increase in the number of TBs and dislocation density in the matrix enhanced the interactions between the TBs and dislocations;

    ?The twinning spreading from coarse grains toward fin grains increased the interactions between the grain boundaries and the TBs.

    The stress-strain curves ofT2andT7in tension shown in Fig.13b demonstrate a similar shape in the detwinning dominant stage where the linear relations between the stress and strain were not observed from the beginning of tensile deformation.According to the evolution of TVF,the stressstrain curve can be subdivided into two regimes.For strain region of 0~0.027(regime 1),TVF decreased linearly with strain indicating the detwinning-dominated regime.For strain>0.027(regime 2),the decrease rate of TVF slows down and to saturate indicating the exhaustion of detwinning.As described above,more grains were involved in twinning atC7than atC2.In regime 1,the twinned regions being favorable for detwinning act like soft grains in comparison with the twin-free grains.Accordingly,stresses during the detwinning stage atT7are expected to be lower than atT2,due to the increase in TVF with increasing cycles.However,the stress-strain curves exhibited an opposite behavior,where the stress in regime 1 atT7is higher than that atT2(Fig.13b).This implies that significan work hardening is accompanied by detwinning.To interpret this,we focused on the shrinkage of twins and the barriers in twins.Numerous LAGBs are observed in twins and their boundary density as well as the KAM value increased with cycle number.The LAGBs(i.e.,dislocation walls)and dislocations in twins can serve as barriers to suppress the motion of TBs.

    As revealed by TEM observation shown in Fig.12,abundant dislocations with<c>-component in the twinned region and detwinned region generated by dislocation transmutation during twinning and detwinning were confirmed The cyclic deformation not only increased the number of TB and dislocation density but also increased the degree of dislocation multiplicity,i.e.,dislocation type.Kadiri and Oppedal[31]and Oppedal et al[32].have reported that the dislocation multiplicity can provide extra hardening through modeling studies.Liu et al[63].conductedin-situTEM observation on Mg single crystal during tension-compression cyclic deformation and found that the stress for detwinning was higher than that of twinning.More types of defects in twins than that in matrix could be responsible to the observed twinning-detwinning asymmetry.Here,the increase in TBs and dislocation density and multiplicity led to the enhanced interaction between dislocations and motion of TBs,and this is considered to increase the stress during the detwinning stage in regime 1.

    In regime 2,there is no deformation mode accommodating the strain due to the exhaustion of detwinning,and then the stress-strain curve behaves more elastically.The reduced peak stress at the largest tensile strain in a large number of cycles was due to larger strain needed for detwinning a larger amount of twinned region,which squeezed the strain of regime 2 for elastic strain hardening.

    From the above discussion,the activities of twinning and detwinning during cyclic deformation are closely related to the microstructure parameters including grains size and dislocation structures.Moreover,the favorability of twinning and detwinning is also strongly depended on the crystallographic orientation of the grains,but was not deeply discussed in present work and will be investigated and reported in the near future.

    5.Conclusions

    In summary,in-situND,identical area EBSD,and TEM techniques were employed to systematically evaluate the cyclic compression-tension deformation behavior of the extruded AZ31 alloy.The specifi conclusions are as follows:

    (1)The compressive deformation was dominated by twinning.Detwinning occurred during unloading after compression and dominated the tensile deformation.A basal slip was also activated in both the matrix and twins.

    (2)With increasing number of cycles,the TVF at-2%strain gradually increased from 26.3%(1st cycle)to 43.5%(8th cycle).Meanwhile,the twinning spread from coarse grains to fin grains involving more grains for twinning.

    (3)The lattice defects including TBs,LAGBs and dislocations were introduced by cyclic deformation and their densities increased with cyclic number.

    (4)After the tension step,the volume fraction and number of residual twins increased with cycle number,which led to the decrease in yield stress in the subsequent compression.

    (5)Dense<c>-component dislocations observed in twins and matrices near the TBs were generated by the dislocation transmutation during twinning and detwinning,respectively.

    (6)The accumulation of dislocations and the increase in the number of TBs did not contribute to work hardening independently,but through the interaction between them during twinning and detwinning to enhance the work hardening,which is believed to play a crucial role in cyclic deformation of the commercial AZ31 alloy.

    Acknowledgments

    This work was financiall supported by the Elements Strategy Initiative for Structural Materials(ESISM,grant No.JPMXP0112101000)in Kyoto University.RXZ was supported by National Natural Science Foundation of China(NSFC,No.51901007).SH and KA were supported by JSPS KAKENHI Nos.JP18H05479 and JP18H05476.The neutron diffraction experiments at the Materials and Life Science Experimental Facility of the J-PARC were performed under a project program(Project No.2014P0102).

    欧美激情国产日韩精品一区| 伦理电影大哥的女人| 亚洲欧美精品自产自拍| 精品久久久久久电影网 | 中文字幕av在线有码专区| 黄色日韩在线| 国产精品无大码| 淫秽高清视频在线观看| 精品无人区乱码1区二区| 国产高清三级在线| 午夜福利在线观看免费完整高清在| 少妇人妻一区二区三区视频| 听说在线观看完整版免费高清| 男插女下体视频免费在线播放| 亚洲精品456在线播放app| 国产午夜精品一二区理论片| 2022亚洲国产成人精品| 国产精品爽爽va在线观看网站| 欧美色视频一区免费| 九九爱精品视频在线观看| 91精品一卡2卡3卡4卡| 国产精品综合久久久久久久免费| 一边亲一边摸免费视频| 水蜜桃什么品种好| 国产在线男女| 人人妻人人澡欧美一区二区| 日韩成人av中文字幕在线观看| 精品无人区乱码1区二区| av专区在线播放| 国产精品一区二区性色av| 亚洲精品色激情综合| av国产久精品久网站免费入址| 亚洲av不卡在线观看| 欧美日本视频| 91av网一区二区| 国产黄色小视频在线观看| 99热这里只有是精品在线观看| 欧美变态另类bdsm刘玥| 亚洲乱码一区二区免费版| 九九热线精品视视频播放| 国产精品久久久久久精品电影小说 | 人妻制服诱惑在线中文字幕| 成人国产麻豆网| 日本免费a在线| 青春草国产在线视频| 麻豆一二三区av精品| 精品人妻偷拍中文字幕| 亚洲最大成人av| 一级黄片播放器| 18+在线观看网站| 91午夜精品亚洲一区二区三区| 高清av免费在线| 国产老妇伦熟女老妇高清| 天堂网av新在线| 欧美三级亚洲精品| 国产精品人妻久久久影院| 国产精华一区二区三区| 亚洲在线观看片| 精品熟女少妇av免费看| 精品久久国产蜜桃| 少妇熟女欧美另类| 久久鲁丝午夜福利片| 少妇人妻一区二区三区视频| 欧美激情在线99| 亚洲人成网站在线播| 国产精品一区二区三区四区免费观看| 五月伊人婷婷丁香| 丰满少妇做爰视频| 国产又黄又爽又无遮挡在线| 三级国产精品欧美在线观看| 91久久精品国产一区二区三区| 熟女人妻精品中文字幕| 亚洲av中文字字幕乱码综合| 日本与韩国留学比较| 一级毛片久久久久久久久女| 亚洲人成网站在线播| 人人妻人人澡人人爽人人夜夜 | 国产黄a三级三级三级人| 1024手机看黄色片| 亚洲成av人片在线播放无| 国产精品乱码一区二三区的特点| 菩萨蛮人人尽说江南好唐韦庄 | 人妻制服诱惑在线中文字幕| 99热网站在线观看| 在线免费十八禁| 欧美潮喷喷水| 欧美又色又爽又黄视频| 国产精品女同一区二区软件| 精品久久久久久成人av| 亚洲电影在线观看av| 亚洲国产欧洲综合997久久,| 午夜激情欧美在线| 九草在线视频观看| 爱豆传媒免费全集在线观看| 亚洲成人久久爱视频| 成人欧美大片| 亚洲欧美日韩无卡精品| 国产精品久久视频播放| 日本一本二区三区精品| 亚洲精品乱码久久久久久按摩| 最近视频中文字幕2019在线8| 建设人人有责人人尽责人人享有的 | 人人妻人人澡欧美一区二区| 午夜福利在线观看吧| 国产大屁股一区二区在线视频| 日本免费在线观看一区| 国产精品日韩av在线免费观看| 免费黄色在线免费观看| 不卡视频在线观看欧美| 美女黄网站色视频| 亚洲人与动物交配视频| www.av在线官网国产| 久久精品夜夜夜夜夜久久蜜豆| 18禁在线无遮挡免费观看视频| 精品人妻一区二区三区麻豆| 又粗又爽又猛毛片免费看| 最近视频中文字幕2019在线8| 成人二区视频| 插逼视频在线观看| 国产亚洲最大av| 国产单亲对白刺激| 熟女电影av网| 国产精品精品国产色婷婷| 国产精品久久久久久久久免| 国产极品精品免费视频能看的| 亚洲内射少妇av| 99热这里只有是精品在线观看| 人妻制服诱惑在线中文字幕| 又粗又硬又长又爽又黄的视频| 非洲黑人性xxxx精品又粗又长| 亚洲性久久影院| 黄片wwwwww| 最后的刺客免费高清国语| 久久久久久久亚洲中文字幕| av在线观看视频网站免费| 一区二区三区四区激情视频| 成人美女网站在线观看视频| 日本五十路高清| 嫩草影院新地址| 久久久久久久久久久丰满| 精品熟女少妇av免费看| 欧美性感艳星| 十八禁国产超污无遮挡网站| 人人妻人人澡欧美一区二区| 禁无遮挡网站| 高清视频免费观看一区二区 | 亚洲国产最新在线播放| 小蜜桃在线观看免费完整版高清| 日韩精品有码人妻一区| 国产精品美女特级片免费视频播放器| 麻豆成人av视频| 久久精品夜夜夜夜夜久久蜜豆| 大香蕉97超碰在线| 欧美人与善性xxx| 久久99热这里只有精品18| 日韩亚洲欧美综合| 久久鲁丝午夜福利片| 色吧在线观看| 欧美丝袜亚洲另类| 高清午夜精品一区二区三区| or卡值多少钱| 国产精品久久电影中文字幕| 国产乱人视频| 国产精品久久久久久av不卡| 亚洲人成网站在线观看播放| 亚洲伊人久久精品综合 | 国产高清不卡午夜福利| 久久久精品欧美日韩精品| 中文字幕免费在线视频6| 永久网站在线| av视频在线观看入口| 久久久a久久爽久久v久久| 亚洲精品乱码久久久久久按摩| 两个人视频免费观看高清| 乱码一卡2卡4卡精品| 日韩av不卡免费在线播放| 亚洲欧美日韩卡通动漫| 精品久久久久久久人妻蜜臀av| 五月伊人婷婷丁香| 国产麻豆成人av免费视频| 亚洲国产精品合色在线| 国产精品三级大全| 中文字幕亚洲精品专区| 亚洲精品乱码久久久久久按摩| 久久6这里有精品| 亚洲av成人精品一区久久| 男女啪啪激烈高潮av片| 国模一区二区三区四区视频| 欧美日韩国产亚洲二区| av又黄又爽大尺度在线免费看 | 午夜福利高清视频| 亚洲婷婷狠狠爱综合网| 欧美+日韩+精品| 国产精品,欧美在线| 青春草国产在线视频| 亚洲成人av在线免费| 成年女人永久免费观看视频| 高清在线视频一区二区三区 | 亚洲欧美日韩高清专用| 成年版毛片免费区| 亚洲av电影在线观看一区二区三区 | 欧美成人a在线观看| 啦啦啦韩国在线观看视频| 国产一区二区三区av在线| 日本一二三区视频观看| 少妇高潮的动态图| 舔av片在线| 精品人妻一区二区三区麻豆| www日本黄色视频网| 亚洲av免费高清在线观看| 欧美+日韩+精品| 爱豆传媒免费全集在线观看| 99热这里只有精品一区| 蜜臀久久99精品久久宅男| 欧美成人a在线观看| 赤兔流量卡办理| 日本wwww免费看| 国产中年淑女户外野战色| h日本视频在线播放| 亚洲欧洲日产国产| 真实男女啪啪啪动态图| 只有这里有精品99| 简卡轻食公司| 国产熟女欧美一区二区| 两个人视频免费观看高清| 插逼视频在线观看| 丝袜美腿在线中文| 国产伦理片在线播放av一区| 亚洲内射少妇av| 日本三级黄在线观看| 国产乱人视频| 在现免费观看毛片| 国产精品国产高清国产av| 97在线视频观看| av线在线观看网站| 亚洲成人中文字幕在线播放| 亚洲欧美日韩高清专用| 欧美不卡视频在线免费观看| 日本免费a在线| 国产探花在线观看一区二区| 99热网站在线观看| 欧美另类亚洲清纯唯美| 国产三级中文精品| 2021少妇久久久久久久久久久| 欧美人与善性xxx| 亚洲熟妇中文字幕五十中出| 亚洲国产精品国产精品| 久久99蜜桃精品久久| 亚洲最大成人手机在线| 国产精品一区二区在线观看99 | 亚洲精品影视一区二区三区av| 波多野结衣巨乳人妻| 99久久中文字幕三级久久日本| 超碰97精品在线观看| 大话2 男鬼变身卡| 午夜免费激情av| 人妻制服诱惑在线中文字幕| 在线观看美女被高潮喷水网站| 亚洲在线自拍视频| 久久久成人免费电影| 建设人人有责人人尽责人人享有的 | 欧美精品国产亚洲| 九九爱精品视频在线观看| 亚洲真实伦在线观看| 老司机影院成人| 国产精品99久久久久久久久| 嫩草影院精品99| 一级爰片在线观看| 国内揄拍国产精品人妻在线| 亚洲精品456在线播放app| 中文字幕av成人在线电影| 插阴视频在线观看视频| 国产精品.久久久| 嫩草影院精品99| 国产色婷婷99| 久久久久久久久大av| 极品教师在线视频| 国产精品国产三级专区第一集| 亚洲四区av| h日本视频在线播放| 超碰av人人做人人爽久久| 99热精品在线国产| 国产欧美另类精品又又久久亚洲欧美| 亚洲不卡免费看| 亚洲精品,欧美精品| 中文乱码字字幕精品一区二区三区 | 国产成人精品久久久久久| 91在线精品国自产拍蜜月| 国产色婷婷99| 国产高清视频在线观看网站| 一级爰片在线观看| 久久久久久久久久黄片| 观看免费一级毛片| 99久久中文字幕三级久久日本| 老司机福利观看| 日日啪夜夜撸| 最近的中文字幕免费完整| 日本-黄色视频高清免费观看| 69av精品久久久久久| 日韩成人伦理影院| 青春草亚洲视频在线观看| 国产色婷婷99| 长腿黑丝高跟| videos熟女内射| 少妇丰满av| 国产单亲对白刺激| 国产 一区精品| 日韩一区二区三区影片| 永久免费av网站大全| 成人午夜高清在线视频| 十八禁国产超污无遮挡网站| 日日啪夜夜撸| 97热精品久久久久久| kizo精华| 亚洲国产精品专区欧美| 热99re8久久精品国产| 色综合色国产| 久久精品久久精品一区二区三区| 亚洲,欧美,日韩| 久久久精品94久久精品| 免费一级毛片在线播放高清视频| 亚洲熟妇中文字幕五十中出| 免费观看精品视频网站| 中文精品一卡2卡3卡4更新| av线在线观看网站| 99热网站在线观看| 国产综合懂色| 色吧在线观看| 一级爰片在线观看| 亚洲av成人av| 日韩视频在线欧美| 变态另类丝袜制服| 啦啦啦韩国在线观看视频| 亚洲av免费在线观看| 久久久久久久久久久丰满| 在线观看一区二区三区| 欧美成人午夜免费资源| 久久久成人免费电影| 内地一区二区视频在线| 热99在线观看视频| 国产精品永久免费网站| 菩萨蛮人人尽说江南好唐韦庄 | 久久99蜜桃精品久久| 久久人人爽人人片av| 国产乱人视频| 韩国av在线不卡| 亚洲精品乱码久久久久久按摩| 简卡轻食公司| 国产三级中文精品| 国产精品一二三区在线看| 久久久午夜欧美精品| 在线免费观看不下载黄p国产| 纵有疾风起免费观看全集完整版 | 成人鲁丝片一二三区免费| 日本五十路高清| 韩国av在线不卡| 男人舔奶头视频| 最近的中文字幕免费完整| 成人毛片60女人毛片免费| 日韩亚洲欧美综合| 精品不卡国产一区二区三区| 国产亚洲av嫩草精品影院| 精品不卡国产一区二区三区| 美女cb高潮喷水在线观看| 你懂的网址亚洲精品在线观看 | 国产av在哪里看| 三级毛片av免费| 又粗又爽又猛毛片免费看| 国产成人aa在线观看| 欧美精品一区二区大全| 水蜜桃什么品种好| 国产亚洲5aaaaa淫片| 午夜激情福利司机影院| 日本五十路高清| 建设人人有责人人尽责人人享有的 | 成人漫画全彩无遮挡| 日日摸夜夜添夜夜添av毛片| 美女xxoo啪啪120秒动态图| 亚洲性久久影院| 青青草视频在线视频观看| 久久久久久久久久成人| 久久6这里有精品| 亚洲色图av天堂| 久久韩国三级中文字幕| 最近中文字幕2019免费版| 插阴视频在线观看视频| 1000部很黄的大片| 精品无人区乱码1区二区| 蜜臀久久99精品久久宅男| 日本黄色片子视频| 26uuu在线亚洲综合色| 中文字幕制服av| 免费播放大片免费观看视频在线观看 | 99久久九九国产精品国产免费| 国产免费视频播放在线视频 | 高清日韩中文字幕在线| 国产成人a区在线观看| 99在线人妻在线中文字幕| 美女脱内裤让男人舔精品视频| 国产在视频线精品| 边亲边吃奶的免费视频| 久久久久性生活片| 婷婷色综合大香蕉| 尤物成人国产欧美一区二区三区| 亚洲国产欧美在线一区| 国产在线男女| 校园人妻丝袜中文字幕| 免费av不卡在线播放| 午夜免费激情av| 国产精品一区二区性色av| 熟女人妻精品中文字幕| 国产午夜精品久久久久久一区二区三区| 国产单亲对白刺激| 久久婷婷人人爽人人干人人爱| 中文在线观看免费www的网站| 亚洲精品色激情综合| 欧美潮喷喷水| 免费看美女性在线毛片视频| 黄色配什么色好看| 一边摸一边抽搐一进一小说| 身体一侧抽搐| 中文字幕精品亚洲无线码一区| 国产极品天堂在线| 久热久热在线精品观看| 美女国产视频在线观看| 欧美97在线视频| 国产精品日韩av在线免费观看| 国产亚洲精品av在线| 嫩草影院新地址| 亚洲av二区三区四区| 春色校园在线视频观看| 日韩av在线免费看完整版不卡| 久久精品国产亚洲网站| 婷婷色综合大香蕉| 老师上课跳d突然被开到最大视频| 亚洲av福利一区| 亚洲人成网站在线观看播放| 日日干狠狠操夜夜爽| .国产精品久久| 亚洲最大成人手机在线| 久久久午夜欧美精品| 久热久热在线精品观看| 高清日韩中文字幕在线| 成人午夜精彩视频在线观看| 青青草视频在线视频观看| 女人久久www免费人成看片 | 国产极品天堂在线| 亚洲av电影不卡..在线观看| 亚洲一级一片aⅴ在线观看| 国产探花在线观看一区二区| 欧美一区二区亚洲| 国产高清不卡午夜福利| 国产人妻一区二区三区在| 日产精品乱码卡一卡2卡三| 久久精品国产99精品国产亚洲性色| 日本熟妇午夜| 听说在线观看完整版免费高清| 国内精品一区二区在线观看| 春色校园在线视频观看| 久久欧美精品欧美久久欧美| 中文字幕免费在线视频6| 美女黄网站色视频| 久久久久久久久中文| 久久精品久久精品一区二区三区| 全区人妻精品视频| 精品无人区乱码1区二区| 黄片wwwwww| 久久人妻av系列| 一级毛片电影观看 | 欧美一区二区国产精品久久精品| 一个人看视频在线观看www免费| 午夜福利在线观看吧| 1000部很黄的大片| 又爽又黄无遮挡网站| 久久亚洲精品不卡| 成人一区二区视频在线观看| 一级毛片久久久久久久久女| 人体艺术视频欧美日本| 狂野欧美白嫩少妇大欣赏| 91av网一区二区| 国产亚洲av片在线观看秒播厂 | 亚洲欧美日韩卡通动漫| 国产一级毛片七仙女欲春2| 免费黄色在线免费观看| 国内揄拍国产精品人妻在线| 成人一区二区视频在线观看| 久久精品久久精品一区二区三区| 久久精品91蜜桃| 国产麻豆成人av免费视频| 亚洲精品成人久久久久久| 日韩欧美国产在线观看| 狂野欧美激情性xxxx在线观看| 九草在线视频观看| 欧美色视频一区免费| 亚洲自拍偷在线| 中文字幕人妻熟人妻熟丝袜美| 成年女人永久免费观看视频| 精品酒店卫生间| 毛片女人毛片| 国产精品无大码| 国产综合懂色| 欧美性感艳星| 国产精品久久久久久久电影| 99热这里只有是精品在线观看| 国产伦精品一区二区三区视频9| 成人一区二区视频在线观看| 一区二区三区四区激情视频| 我的老师免费观看完整版| 国产单亲对白刺激| 黑人高潮一二区| 亚洲成av人片在线播放无| 美女内射精品一级片tv| 国产三级中文精品| 国产在线一区二区三区精 | 男女那种视频在线观看| 舔av片在线| 欧美日韩综合久久久久久| 水蜜桃什么品种好| 国内揄拍国产精品人妻在线| 免费一级毛片在线播放高清视频| 卡戴珊不雅视频在线播放| 一区二区三区高清视频在线| 亚洲av电影不卡..在线观看| 日本猛色少妇xxxxx猛交久久| 人妻制服诱惑在线中文字幕| 亚洲国产色片| 免费播放大片免费观看视频在线观看 | 亚洲av日韩在线播放| 日本黄色片子视频| 久久久久久久久久黄片| 内射极品少妇av片p| 国内精品宾馆在线| 91av网一区二区| 久久久精品大字幕| 午夜亚洲福利在线播放| 亚洲av日韩在线播放| 国产v大片淫在线免费观看| 亚洲精品色激情综合| 久久精品国产亚洲av涩爱| 99久国产av精品国产电影| 深夜a级毛片| 欧美一级a爱片免费观看看| 嫩草影院新地址| 麻豆久久精品国产亚洲av| 91精品国产九色| АⅤ资源中文在线天堂| 国产精品.久久久| 最近2019中文字幕mv第一页| 精品久久久久久电影网 | 六月丁香七月| 久久精品人妻少妇| 别揉我奶头 嗯啊视频| or卡值多少钱| 你懂的网址亚洲精品在线观看 | 97超视频在线观看视频| 高清视频免费观看一区二区 | 99热全是精品| 亚洲av成人精品一二三区| 小蜜桃在线观看免费完整版高清| 成人午夜高清在线视频| 人体艺术视频欧美日本| 亚洲国产精品成人久久小说| 久久精品国产自在天天线| 一级毛片aaaaaa免费看小| 一个人观看的视频www高清免费观看| 久久精品人妻少妇| 亚洲天堂国产精品一区在线| 视频中文字幕在线观看| 亚洲精品aⅴ在线观看| 国产精品久久电影中文字幕| 日韩强制内射视频| 亚洲电影在线观看av| 如何舔出高潮| 久久精品综合一区二区三区| 老司机影院毛片| 国产69精品久久久久777片| 国产男人的电影天堂91| 黄色配什么色好看| 少妇人妻精品综合一区二区| 最近最新中文字幕免费大全7| 国产精品99久久久久久久久| 在线免费十八禁| 久久婷婷人人爽人人干人人爱| 欧美日本视频| 欧美色视频一区免费| 成人国产麻豆网| 久久亚洲国产成人精品v| 一本一本综合久久| 免费播放大片免费观看视频在线观看 | 久久欧美精品欧美久久欧美| av在线老鸭窝| 丝袜美腿在线中文| 国产极品天堂在线| 亚洲在线观看片| 91精品伊人久久大香线蕉| 日韩一本色道免费dvd| 国产亚洲av片在线观看秒播厂 | 一本一本综合久久| 成人国产麻豆网| 亚洲无线观看免费| 国产精品久久久久久精品电影小说 | 婷婷色av中文字幕| 久久精品影院6| 国产精品1区2区在线观看.| 桃色一区二区三区在线观看| 精品午夜福利在线看| 三级经典国产精品| 久久久国产成人免费| 91aial.com中文字幕在线观看| 欧美另类亚洲清纯唯美| 黑人高潮一二区| 尾随美女入室| 亚洲国产最新在线播放| 日韩av不卡免费在线播放| 欧美另类亚洲清纯唯美|