• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Corrosion behavior of fine-graine Mg-7.5Li-3Al-1Zn fabricated by extrusion with a forward-backward rotating die (KoBo)

    2022-07-16 03:36:30AnnDokowskBogusAdmzykCieslkMilenKorlnikWitoldChrominskiJiriKusekJkuCiftiDriuszKuJrosMizer
    Journal of Magnesium and Alloys 2022年3期

    Ann Dokowsk ,Bogus?w Admzyk -Cie′slk ,Milen Korlnik ,Witold Chromi′nski ,Jiri Kusek ,Jku Cifti ,Driusz Ku,Jros?w Mizer

    aFaculty of Materials Science and Engineering,Warsaw University of Technology,141 Woloska,St,Warsaw 02-507,Poland

    b Department of Metals and Corrosion Engineering,University of Chemistry and Technology,Technicka 5,Prague 6 166 28,Czechia

    c Institute of Materials Engineering,Silesian University of Technology,Krasi′nskiego 8,Katowice 40-019,Poland

    Abstract The microstructure-dependent corrosion resistance of dual structured fine-graine Mg-7.5Li-3Al-1Zn has been investigated.The alloys were extruded using extrusion with a forward-backward rotating die (KoBo,a newly developed SPD method) at two different extrusion ratios.The fine-graine microstructures formed in the alloys were characterized,and the influenc of grain refinemen on corrosion resistance was analyzed.For fine-graine (α + β) Mg-Li alloys,a higher extrusion ratio led to more intensive grain refinement however,this relationship did not improve their corrosion resistance in a chloride-containing solution.The corrosion resistance of the alloys was mainly controlled by the refinemen of α(Mg) and β(Li),along with the distribution of second phases.The presence of MgLi2Al at grain boundaries facilitated their dissolution.

    Keywords: Corrosion;Grain refinement Grain size distribution;Magnesium alloy.

    1.Introduction

    Dual-phase structured Mg-Li alloys have drawn extensive scientifi attention,and they have been widely investigated in terms of their microstructure and the improvement of their mechanical properties by microstructure refinemen and second-phase strengthening using plastic or thermal processing [1-9].Many attempts have been made to evaluate the mechanical properties of ultrafine-graine (α+β) Mg-Li,which have been fabricated using severe plastic deformation (SPD)methods,such as high-pressure torsion [5,10],double-change angular pressing [11],and equal-channel angular extrusion[12].The occurrence of superplasticity was reported for dualstructured Mg-Li alloys processed by equal-channel angular pressing [13,14],heavy rolling and nitrate bath annealing[15],or forging [16].Another method giving a possibility of significan grain refinemen is a combination of an extrusion with applied additional plastic deformation by reversible torsion of the die (KoBo) [17].The KoBo method allows a very high deformation to be obtained at room temperature and has been previously used for Mg-Li alloys [18,19].

    There have been many trials to describe the corrosion resistance of dual-phase structured Mg-Li alloys;nevertheless,the associated corrosion mechanisms are quite poorly described in the literature.This phenomenon is due to the fact that the corrosion behavior of dual-structure Mg-Li is a complex process [20-24],and in addition to multiple microgalvanic processes caused by the presence of second-phase precipitation in the matrix [25,26],many other microstructure-dependent mechanisms proceed simultaneously [27,28].Pitting and filifor corrosion are the most observed types of corrosion in dual-structured Mg-Li alloys[22,23,29,30].It should be noted that the corrosion rate of dual-structured Mg-Li alloys is the highest when compared to singleα-structured and singleβ-structured Mg-Li [31].

    Generally,the corrosion resistance of Mg-Li alloys increases with microstructure refinemen [31-34].It has been shown that grain refinemen resulting from extrusion at an extrusion ratio of 20:4:1 improved the corrosion resistance of Mg-9.29Li-0.88Ca and changed the form of corrosion from pitting to general corrosion for extruded alloys with a higher extrusion ratio [35].In addition,it has been demonstrated that grain refinemen caused by rolling supported oxide fil formation [33].Yang et al.[22] showed that in Mg-8Li-3Zn-Al in 3.5 wt.% NaCl solution,Cl-ions led to the initiation and development of corrosion pits.It has also been noted thatβ(Li),which is more active thanα(Mg) (since Li is a very active metal),played the major role in the corrosion behavior of Mg-Li alloys [23,36].Another study showed that although the Volta potential ofα(Mg) phases is much higher than that ofβ(Li) phases,pitting occurrence was preferentially related to theα(Mg) phases,but not the (β)Li phases [36].

    Due to their hexagonal close-packed (hcp) crystal structure,which results in a limited number of slip systems and anisotropic deformation,Mg-alloys are hard to deform[37,38].Hence,the possibility of significan grain refinemen(to fin grains with dimensions below 10 μm) for these materials is limited,but may be accomplished under conditions of permanent destabilization of their microstructure by methods where a high deformation rate can be applied [39].Due to its additional reversible oscillating die at the end of its extrusion injection cylinder,extrusion with a forward-backward rotating die (KoBo) allows for the deformation at lower temperatures than used so far of materials that are hard to deform (i.e.Mg-based alloys),by the introduction of a large deformation until a viscoplastic material fl w phenomenon occurs in the material [40].

    The KoBo is a newly developed technique among SPD methods,which may be used for the reduction of the dimensions of Mg-based alloys [41].Therefore,in this study the firs examination of microstructure-dependent corrosion in chloride-containing solution of two Mg-7.5Li-3Al-1Zn alloys extruded via a KoBo is described.

    2.Methodology

    2.1.Microstructural characterization

    The firs step in this study was to characterize the phase compositions of the alloys.Atomic absorption spectrometry(AAS,GBC 932 Plus) was performed to calculate the Li concentration in both the analyzed materials.X-ray diffraction(XRD,Bruker D8 Advance),operating at 40 kV and 40 mA with Cu Kαradiation,was used to characterize the detailed phase composition of the alloys.The results were recorded by stepwise scanning 2θf(wàn)rom 10° to 120°,with a step size of 0.02° and a count time of 10 s per step.A semi-quantitative analysis of the relative concentration of the phases present in the alloys was carried out by comparing the integrated intensities of the diffraction peaks from each of the known phases.

    The microstructure of the alloys was observed using a high-resolution scanning electron microscope (SEM,Hitachi SU8000).The extruded wires were cut into 3 mm-thick slices,polished with 1200-grit and 2400-grit SiC papers,and subsequently surfaces perpendicular to the extrusion direction were polished with a low-energy Ar+ion beam milling system(Hitachi IM4000 Ion Milling System) for 6 h.Observations were carried out immediately after sample preparation.

    A transmission electron microscope (TEM,JEOL JEM-1200EX) with an acceleration voltage of 120 kV was used to investigate the dislocation distribution and to characterize the details of the phases formed in the alloys.Samples in the form of thin foils were prepared using a Gatan Model 656 Dimple Grinder and a Gatan Model 691 Precision Ion Polishing System (PIPS) at 2.5 kV.The observations were carried out on cross-sections perpendicular to the extrusion direction.

    2.2.Corrosion tests

    Electrochemical measurements were carried out in naturally aerated,quiescent 0.1 M NaCl solution using an FAS1 Gamry potentiostat equipped with three electrodes:platinum as the counter electrode,saturated Ag/AgCl as the reference electrode,and the measured sample as the working electrode.The electrolyte was produced using analytical grade reagents and distilled water.The corrosion potential(Ecorr) was recorded for 1 h under open-circuit conditions.After immersion,potentiodynamic tests were conducted with a scan rate of 5 mV/s,starting 0.5 V below EOCPand finishin at 2 V vs.Ref.The polarization curves were fitte using Gamry Echem software in Tafel mode.The post-corrosion morphology of the samples was observed after 1 h immersion under open-circuit conditions using scanning electron microscopy (SEM,Hitachi SU8000).

    To compare the corrosion resistance of the alloys,the corrosion rate (Vc) was calculated based on traditional mass loss measurements.Samples were polished up to 4000-grit SiC paper,ultrasonically cleaned in isopropanol and dried in the air.Prior to immersion,the surface area of the samples was measured,and the samples were weighted.Afterwards samples were immersed for 1 h in naturally aerated 0.1 M NaCl.After immersion,samples were dried in the air and corrosion products were removed by samples immersion in 7% solution of nitric acid (HNO3) for 15 s (as per [42,43]).The Vcwas calculated [44]:

    where:Δm is a mass loss (g),t is a time of exposure (day),s is a surface area (m2).

    Corrosion rate of the investigated materials were compared with the results obtained for traditionally extruded and annealed Mg-7.5Li-3Al-1Zn alloy (coarse-grained alloy described in [45]).

    Fig.1.Extrusion with a forward-backward rotating die (KoBo).

    To describe the role of microstructure in the corrosion resistance of both alloys,the corrosion products formed on the samples as well as surfaces with chemically removed corrosion products had been chemically removed,were observed using SEM.Cross-sectional observations were also made.

    3.Deformation method and materials

    The materials examined in this study were extruded using the KoBo method.As shown in Fig.1,during KoBo extrusion,the input material is punch-pressed through the matrix where the oscillations of the bilaterally rotating die occur.This specifi combination allows for extrusion under conditions of permanent microstructure destabilization by applying a high deformation rate and leads to the formation of a fine-graine microstructure (approx.<10 μm) [40,46].The extrusion was performed under the following conditions:punch speed=0.2 mm/s,die rotation angle=8°,initial temperature of the billet=24 °C,and die oscillation frequency=5 Hz (±1 Hz).

    In this study,two fine-graine Mg-7.5Li-3Al-1Zn(AZ31+7.5 wt.%Li) alloys extruded using the KoBo were investigated.The firs was extruded at an extrusion ratio of R1=40:4,giving a deformation degree ofλ1=100,while the second was extruded at an extrusion ratio of R2=40:2,givingλ2=400.

    4.Results

    4.1.Microstructure characterization

    As Li is a chemically active metal,it was necessary to confir the Li concentration in the extruded rods.As listed in Table 1,the concentration of Li after extrusion to the fina dimension of ?4 mm slightly decreased from the initial amount of 7.5 wt.% to 7.0 wt.%,and to 5.7 wt.% after extrusion to ?2 mm.Similarly to their coarse-grained counterparts [45],both materials exhibited a dual-phased structure composed of light areas ofα(Mg) and dark areas ofβ(Li),Fig.2.The darkβ(Li) was irregularly distributed in the alloy extruded to ?4 mm,and its twisted shape (Fig.3a,b) may have been a result of the insufficien frequency of the die oscillation [41];however,this hypothesis needs to be further examined.As a result of the higher degree of deformation,a more uniform microstructure formed (Fig.2c,d).Coarse white Al,Mn-rich phases were precipitated within the matrix of both alloys (marked as P1 in Fig.2b,d).

    Table 1 Li concentration obtained by AAS (wt.%).

    Table 2 Semi-quantitative analysis obtained by XRD for the extruded Mg-7.5Li-3Al-1Zn.

    Moreover,various nano-sized precipitates were formed in the materials,and as shown in the XRD patterns,they were identifie as Mg17Al12,AlLi,and MgLi2Al (Fig.3).To confir their presence,TEM observations were carried out.As shown in Fig.4a,small round Mg17Al12precipitates were randomly distributed in the grain interiors in the alloy extruded to ?4 mm,Fig.4a.Randomly distributed Mg17Al12precipitates,which were similar in shape,were also identifie in the alloy extruded to ?2 mm (Fig.4c).The presence of elongated MgLi2Al precipitates at the grain boundaries was also confirmed and a higher number of them were formed in the alloy extruded to ?2 mm (Fig.4d).Additionally,the existence of round,coarse precipitates is shown in Fig.4b.This kind of precipitates can be identifie as AlLi.Unfortunately,we were not able to perform SAD to confir its presence;however,based on our previous observations,we suppose that the observed shape and distribution can support the classifi cation of these precipitates as AlLi [45].Surprisingly,a few ternary precipitates of and MgLiAl2were detected in the alloy extruded to ?4 mm (Fig.4c).When comparing the TEM microstructure of the alloys extruded at the two extrusion ratios,it can be seen that a higher number of second phases precipitated in the alloy extruded to ?2 mm (Fig.5).These precipitates were formed aroundβ(Li),and they are clearly visible as tiny white threads surrounding the dark areas ofβ(Li) in Fig.2b and d.Despite the differing degrees of deformation,the relative concentrations ofα(Mg) toβ(Li) did not change significantl,and in the alloy extruded to ?4 mm the ratio was 34.1 to 63.2%,while being 27.2 to 71.2% for ?2 mm(Table 2).

    4.2.Corrosion testing

    Fig.2.SEM images showing microstructure of Mg-7.5Li-3Al-1Zn:(a) image showing overall microstructure of the alloy extruded to ?4 mm,(b) image showing distribution of coarse precipitates in the alloy extruded to ?4 mm,(c) image showing overall microstructure of the alloy extruded to ?2 mm,(d)image showing distribution of coarse precipitates in the alloy extruded to ?2 mm,(e) the representative EDX analyzes for precipitates labelled as P1.

    Fig.3.XRD patterns obtained for the examined materials.

    The electrochemical results for both the analyzed materials,performed in naturally aerated 0.1 M NaCl,are shown in Fig.6.The Ecorrevaluation during 1 h of immersion in naturally aerated 0.1 M NaCl for both analyzed materials is shown in Fig.6a.Depending on the deformation ratio,the Ecorrcurves exhibited different trends.Higher values of Ecorrwere recorded for Mg-7.5Li-3Al-1Zn extruded to ?2 mm.At the beginning of immersion,a rapid increase in Ecorrtook place,from the initial value of -1.53 V/Ref to -1.47 V/Ref.During the following 3 min,Ecorrslightly decreased,and then once again increased towards more positive values,reaching -1.45 V/Ref.Subsequently,an abrupt decline occurred to -1.52 V/Ref,the potential remaining around this value,in a nearly steady state,for the remainder of the experiment.Lower values of Ecorrin the analyzed solution,suggesting a poorer resistance to the corrosive environment due to a lower equilibrium potential that made the oxidation process easier [22,47],were registered for the Mg-7.5Li-3Al-1Zn extruded to ?4 mm.In this case,a rapid increase in Ecorroccurred at the start of the immersion,starting below-1.56 V/Ref,reaching a value of around -1.53 V/Ref after 5 min of immersion,and continuing at a near steady state just above -1.53 V/Ref for the remainder of the experiment.The observed initial rapid increase in the Ecorrvalues for the period of<5 min of immersion is unique for Mg-based alloys,and is rather associated with “cathodic activation”than with the suppression of anodic kinetics [31,48].Also,the variations around the steady-state value of Ecorr,recorded for both alloys during the immersion,are attributed to the changes in anodic kinetics under the corrosion conditions[31,48,49].

    Fig.4.TEM images in bright fiel and selected area diffraction (SAD) patterns obtained from the alloy extruded to ?4 mm (a and b),and the alloy extruded to ?2 mm (c and d).

    Fig.5.TEM images of the microstructure of the alloy extruded to ?4 mm (a),and the alloy extruded to ?2 mm (b).

    Fig.6.The results of electrochemical measurements performed in naturally aerated 0.1 M NaCl (a) Ecorr evaluation over 1 h,(b) potentiodynamic polarization curves.

    Fig.6b shows the polarization curves for the Mg-7.5Li-3Al-1Zn alloys deformed to ?2 and ?4 mm,and the characteristic electrochemical parameters calculated from the Tafel slopes are displayed in Table 3.The cathodic branches showed a similar trend in their slopes;however,slightly higher cathodic current densities (ic) were reported for Mg-7.5Li-3Al-1Zn extruded to ?4 mm than for the material extruded to ?2 mm.This trend suggests that the rate of water reduction is higher in the case of Mg-7.5Li-3Al-1Zn extruded to ?4 mm,and may be supported by the presence of second phases that act as local cathodes [50,51].In the anodic branches,a typical infl xion point is visible,related to the breakdown of the protective oxide fil formed on the alloys’ surfaces [49,52,53].This breakdown potential is clearly visible for both alloys;however,Ebwas higher for the material extruded to ?2 mm than for the material extruded to ?4 mm (Eb=-1.24 V/Ref for Mg-7.5Li-3Al-1Zn extruded to ?4 mm,and Eb=-0.97 V/Ref for Mg-7.5Li-3Al-1Zn extruded to ?2 mm,respectively).The portion of the active area of the anodic slope,after reaching Ecorrand preceding the infl xion point (Eb),was shorter for the alloy extruded with a lower extrusion ratio (extruded to ?4 mm) than for the material extruded with a higher extrusion ratio (extruded to ?2 mm),as shown in Fig.7.The greater the differences between these two values,the higher the resistance to the localized corrosion of the respective alloy.Additionally,the alloy extruded at a lower extrusion ratio (?4 mm) presented lower corrosion current density than that extruded with a higher extrusion ratio (Table 3).

    Fig.7.The difference between Ecorr and Eb calculated for both analyzed materials showing susceptibility to localized corrosion.

    Table 3 The electrochemical parameters calculated from Tafel extrapolation based on results from potentiodynamic polarization tests recorded in 0.1 M NaCl.

    The results for the measured mass loss rates are shown in Fig.8.The mass loss results represent the corrosion rate directly,and as presented,the extrusion of Mg-7.5Li-3Al-1Zn to ?4 mm made this alloy the most resistant to the 0.1 M NaCl.The corrosion rate after 1 h of immersion gave results of 0.02 g·day-1·cm-2,which was significantl lower that for coarse-grained Mg-7.5Li-3Al-1Zn (0.5 g·day-1·cm-2).The higher extrusion ratio increased the corrosion activity of the alloy extruded to ?2 mm,giving a corrosion rate of 0.07 g·day-1·cm-2making it still lower than that calculated for its coarse-grained counterpart but higher than that the one obtained for the KoBo extruded alloy to ?4 mm.This indicates,that among SPD extruded dual-structured Mg-Li alloys,higher grain refinemen is not capable of reducing the corrosion rate.

    Fig.8.Corrosion rate calculated after 1 h of immersion in 0.1 M NaCl for conventionally extruded and annealed Mg-7.5Li-3Al-1Zn (coarse-grained),and for Mg-7.5Li-3Al-1Zn KoBo extruded to ?=4 mm and ?=2 mm.

    4.3.Post-corrosion observations

    Fig.9.SEM surface observations of Mg-7.5Li-3Al-1Zn extruded to ?4 mm,after 1 h immersion in naturally aerated 0.1 M NaCl:(a) image showing overall corrosion after immersion,(b) image showing localized corrosion,(c) cross-sectional observations,(d) EDX analysis performed at point A1 in panel c.

    Fig.10.Cross-sectional observations of the corrosion products formed on the Mg-7.5Li-3Al-1Zn extruded to ?2 mm,after 1 h immersion in naturally aerated 0.1 M NaCl:(a) image showing overall corrosion after immersion,(b) image showing localized corrosion,(c) cross-sectional observations,(d) EDX analysis performed at point B1 in panel c.

    SEM images of the surface and its chemical composition(EDX) were obtained after immersion of the samples for a period of 1 h.Figs.9 and 10 depict corrosion attack on the surface and cross-sectional observations of Mg-7.5Li-3Al-1Zn extruded to ?4 mm and to ?2 mm after immersion for 1 h in 0.1 M NaCl.The surface of both alloys suffered from an intense local corrosion attack aligned along some preferred paths (Figs.9a and 10a).The SEM images of the corroded surfaces of both alloys taken with higher magnificatio show that localized corrosion attack was intense and led to the strong dissolution of local areas (Figs.9b and 10b).The cross-sectional images of the samples after immersion under open-circuit conditions revealed that corrosion in Mg-7.5Li-3Al-1Zn extruded to ?4 mm spread apparently selectively,and propagated into the interior of the material (Fig.9c).Theα(Mg) phase had a relatively higher potential of -2.37 vs.SHE,whereasβ(Li) had a much lower potential of -3.41 V vs.SHE [30,54];therefore,in the case of dual-structured Mg-Li alloys,β(Li) was more prone to dissolve thanα(Mg).Based on this preference,it can be claimed that the extension of corrosion proceeded throughβ(Li),as marked in Fig.9c.In the case of the sample extruded with a higher extrusion ratio (to ?2 mm),corrosion spreading at the sample/solution interface led to the formation of a poorly protective layer with a width of<3 μm and was also accompanied by selective and deep local damage to the material (Fig.10c).EDX analyzes shown in Figs.9d and 10d revealed that the corrosion products formed on the surfaces of both alloys were enriched in Mg and Al,suggesting that besides conglomerates with the needle-like crystals typical for brucite(shown in the inset in Fig.10b),other compounds enriched in Al were present,which may support better passivation of the Mg-Li alloys [55,56].Ni and Cu detected during EDX analysis were present because prior to the observations the samples were coated with Ni-Cu.

    After the corrosion products were removed,it was clearly seen that the corroded areas could be identifie with grain boundaries.There are two reasons of this:microgalvanic corrosion would be expected to occur between MgLi2Al and the grain boundary,and the grain boundaries are more prone to serve as an anode with respect to the cathodic grain interior because of their higher distortion (Fig.11).As shown in Fig.11b,the intergranular corrosion extends to intragranular locations,and the attack led to the dissolution ofβ(Li).Clearly,more intensive corrosion occurred at the surface of the material deformed at a higher extrusion ratio.

    5.Discussion

    Fig.11.Images taken after corrosion products were removed:(a) Mg-7.5Li-3Al-1Zn extruded to ?4 mm,(b) Mg-7.5Li-3Al-1Zn extruded to ?2 mm.

    Fig.12.The comparative images of the surfaces.

    The results obtained in this study gave a new insight into the corrosion of dual-structured Mg-Li alloys,which contributed to a better understanding of this process.Our combined microstructural,electrochemical,and analytical study highlighted the differences between the spreading corrosion mechanisms and evaluated the role of various microstructural features in their propagation.It would be expected that higher grain refinemen would give a positive influenc on the corrosion resistance of metallic materials in alkaline and near neutral solutions [35,57].For AZ31B alloy,the effect of grain size played a significan role in the case of an untwined microstructure,for which the corrosion rate was higher when the grain size increased from 65 to 250 μm [58].Also,Li et al.[29] described the corrosion resistance of Mg-5Li alloy,which was improved due to more refine grains.The presented study shows that declaring a definit ve relationship between the grain size and corrosion resistance of metallic materials,especially dual-structured ones,may be an unjustifie interpretation.Grain refinemen via KoBo extrusion improved the corrosion resistance of dual-structured alloys when compared to their coarse-grained counterparts.Among group of fine-graine (α+β) Mg-Li alloys,a higher extrusion ratio led to more intensive grain refinement however,this relationship did not improve their corrosion resistance in chloridecontaining solution.This phenomenon is attributed to two critical factors.First of all,corrosion attack on both the analyzed alloys with fine-graine structure started at the grain boundaries where MgLi2Al was formed.The more refine structure possessed a higher number of grain boundaries with precipitated MgLi2Al where the corrosion may be initialized,and the reactions occurring at grain boundaries were not compensated by reactions leading to the formation of a protective layer.Secondly,an important findin is that the corrosion process is extended throughβ(Li),which is more active thanα(Mg).A microgalvanic coupling betweenβ(Li) andα(Mg)has been previously reported [31,59].In our previous study,we claimed that the corrosion resistance of dual-phased conventionally extruded Mg-7.5Li-3Al-1Zn alloys depends on theα(Mg) toβ(Li) area ratio,where one acts as a cathode and drives the local system to a state of equilibrium [45].This effect forces the second phase to actively corrode,and therefore the amount ofβ(Li) andα(Mg) in the case of coarsegrained dual-structured Mg-Li alloys plays a predominant role in their corrosion mechanisms.In the case of fine-graine dual-structured Mg-Li alloys,regardless of the degree of deformation,the ratio of the relative concentration ofα(Mg) toβ(Li)did not change significantl,and taking this into consideration,it is reasonable to assume that grain refinement and the results of this refinemen on both phases are major factors influencin the corrosion mechanisms in the examined alloys.

    Fig.12 summarizes the microgalvanic corrosion mechanisms in the Mg-7.5Li-3Al-1Zn alloys extruded to ?4 and ?2 mm.The microgalvanic processes in dual-phase Mg-Li alloys are mainly controlled by the anodic to cathodic area ratio ofβ(Li)α(Mg) [45].Nevertheless,at the beginning of the process,in stage I,due to either the formation of a galvanic cell between the MgLi2Al precipitate and grain boundary,or a higher distortion of the grain boundary when compared to the grain interiors,the most preferential corrosion sites were grain boundaries (marked with the red arrow in Fig.12).Although at the beginning of immersion more sites of corrosion initiation were present on the alloy with higher grain refinement the predominant corrosion mechanism occurred during stage II,where microgalvanic corrosion proceeded betweenα(Mg) andβ(Li),and intergranular corrosion was supplemented by an intragranular process.In this case,microgalvanic corrosion was controlled by the area ratio of cathodic to anodic grain interiors.As commonly known for heterogeneous microstructures,the corrosion system was composed of half-cell electrodes,where the phase with the lower potential was anodic,and the phase with higher potential cathodic.Therefore,after reaching stage I,anodic dissolution ofβ(Li) was observed.Moreover,the higher refinemen of both phases resulted in a higher number of microgalvanically coupledα(Mg)/β(Li) grains with a lower area ratio than in the material where the grains were larger.In the latter case the number of microgalvanically coupledα(Mg)/β(Li)grains was lower,and the area ratio ofα(Mg)/β(Li) was higher.This trend influence the spatial distribution of the cathodic and anodic reactions,resulting in a higher degree of penetration for the alloy with the more refine grains.

    6.Conclusion

    In this study,through observing the microstructure and investigating the corrosion behavior of KoBo extruded Mg-7.5Li-3Al-1Zn alloys extruded to ?4 and ?2 mm,the effects ofα(Mg) andβ(Li) distribution,their relative ratio,and the role of second phases have been examined.The following conclusions can be drawn:

    ?The KoBo extrusion to the dimension of ?4 mm led to the formation of non-uniform fine-graine microstructure in dual-structured Mg-7.5Li-3Al-1Zn alloys.The increase in the extrusion ratio caused the formation of homogenous fine-graine dual-structured microstructure.

    ?In the case of fine-graine dual-structured Mg-Li alloys,the main roles in the corrosion mechanism were played by the refinemen ofα(Mg) andβ(Li) and the distribution of second phases.The presence of MgLi2Al at grain boundaries facilitated their dissolution.

    ?For fine-graine (α+β) Mg-Li alloys,a higher extrusion ratio led to more intensive grain refinement however,this relationship did not improve their corrosion resistance in chloride-containing solution.

    成年女人毛片免费观看观看9| 国产爱豆传媒在线观看| 18+在线观看网站| 熟妇人妻久久中文字幕3abv| 国产黄a三级三级三级人| 亚洲成人中文字幕在线播放| 午夜福利在线在线| 日韩欧美 国产精品| 国产精品久久久久久久久免 | 欧美国产日韩亚洲一区| 国产麻豆成人av免费视频| 免费搜索国产男女视频| 在现免费观看毛片| 我要搜黄色片| 十八禁人妻一区二区| 国产一区二区在线av高清观看| 一级毛片久久久久久久久女| 俺也久久电影网| 真人一进一出gif抽搐免费| 亚洲欧美日韩高清专用| 久99久视频精品免费| 首页视频小说图片口味搜索| 亚洲人成网站在线播| 又爽又黄a免费视频| 亚洲欧美日韩高清在线视频| 亚洲av不卡在线观看| 亚洲天堂国产精品一区在线| 亚洲av成人精品一区久久| 欧美一级a爱片免费观看看| 精品久久久久久久人妻蜜臀av| 国产午夜精品论理片| 亚洲 国产 在线| 五月玫瑰六月丁香| 日韩 亚洲 欧美在线| 久久久精品大字幕| 日韩人妻高清精品专区| 黄色视频,在线免费观看| 午夜激情福利司机影院| 国产精品99久久久久久久久| 欧美三级亚洲精品| 国产精品1区2区在线观看.| 久久草成人影院| xxxwww97欧美| 亚洲最大成人中文| 久久99热这里只有精品18| 亚洲黑人精品在线| 最近最新中文字幕大全电影3| 在线观看66精品国产| 国产主播在线观看一区二区| 亚洲欧美清纯卡通| 国产精品电影一区二区三区| 日韩精品青青久久久久久| 国产成人福利小说| 亚洲欧美激情综合另类| 成人高潮视频无遮挡免费网站| 精品人妻视频免费看| 国内毛片毛片毛片毛片毛片| 色av中文字幕| 欧美激情久久久久久爽电影| 亚洲成人中文字幕在线播放| 日韩高清综合在线| 精品人妻一区二区三区麻豆 | 真人一进一出gif抽搐免费| 精品久久久久久久久久久久久| 人人妻人人看人人澡| 精品福利观看| 天堂动漫精品| 欧美色欧美亚洲另类二区| 国产午夜精品论理片| 美女大奶头视频| 一夜夜www| 老司机午夜福利在线观看视频| 国产探花极品一区二区| 国产精品久久久久久精品电影| 欧美zozozo另类| 内地一区二区视频在线| 身体一侧抽搐| 久久久精品欧美日韩精品| 色视频www国产| 久久久久免费精品人妻一区二区| 国产精品av视频在线免费观看| 在线观看午夜福利视频| 麻豆一二三区av精品| 久久欧美精品欧美久久欧美| 国产伦人伦偷精品视频| 亚洲第一电影网av| av在线蜜桃| 国产成人福利小说| 国产视频内射| 一个人看视频在线观看www免费| 18禁黄网站禁片免费观看直播| 午夜亚洲福利在线播放| 国产又黄又爽又无遮挡在线| 亚洲第一区二区三区不卡| 国产高清视频在线观看网站| 桃色一区二区三区在线观看| 婷婷精品国产亚洲av| 丰满的人妻完整版| 亚洲人与动物交配视频| 久久久久国产精品人妻aⅴ院| 少妇丰满av| 国模一区二区三区四区视频| av专区在线播放| 神马国产精品三级电影在线观看| 毛片一级片免费看久久久久 | 免费一级毛片在线播放高清视频| 亚洲精品日韩av片在线观看| 亚洲最大成人手机在线| 国产午夜精品论理片| eeuss影院久久| 久久天躁狠狠躁夜夜2o2o| 久久国产精品人妻蜜桃| 精品人妻1区二区| 日本a在线网址| 亚洲不卡免费看| 亚洲国产高清在线一区二区三| АⅤ资源中文在线天堂| 精品日产1卡2卡| 在线a可以看的网站| 亚洲熟妇中文字幕五十中出| 国产精华一区二区三区| 国产av麻豆久久久久久久| 亚洲精品在线观看二区| 日韩高清综合在线| 亚洲无线观看免费| 美女黄网站色视频| 色视频www国产| 久久久久久久久久成人| 搡女人真爽免费视频火全软件 | 久久中文看片网| 欧美性猛交╳xxx乱大交人| 夜夜夜夜夜久久久久| 亚洲,欧美,日韩| 一进一出抽搐gif免费好疼| 麻豆久久精品国产亚洲av| 免费高清视频大片| 欧美日韩亚洲国产一区二区在线观看| 我的老师免费观看完整版| 成人特级av手机在线观看| 久久精品国产99精品国产亚洲性色| 亚洲国产精品合色在线| 精品久久久久久久久av| 日韩欧美在线二视频| 欧美三级亚洲精品| 精品免费久久久久久久清纯| 日本一本二区三区精品| 少妇人妻一区二区三区视频| 一本一本综合久久| 少妇熟女aⅴ在线视频| 国产免费av片在线观看野外av| 欧美乱妇无乱码| 成人精品一区二区免费| 亚洲国产精品sss在线观看| 男女视频在线观看网站免费| 少妇的逼水好多| 一级a爱片免费观看的视频| 香蕉av资源在线| 国产真实乱freesex| 韩国av一区二区三区四区| 久久精品久久久久久噜噜老黄 | 久久久精品大字幕| eeuss影院久久| 国产亚洲av嫩草精品影院| 小蜜桃在线观看免费完整版高清| 亚洲成人精品中文字幕电影| 我要搜黄色片| 亚洲人成伊人成综合网2020| 欧美高清性xxxxhd video| 特级一级黄色大片| 热99在线观看视频| 美女 人体艺术 gogo| 久久久久国产精品人妻aⅴ院| 亚洲av免费在线观看| 国产麻豆成人av免费视频| 中文字幕av在线有码专区| 精品一区二区三区人妻视频| 男人舔女人下体高潮全视频| 老鸭窝网址在线观看| 高潮久久久久久久久久久不卡| 又粗又爽又猛毛片免费看| 91在线精品国自产拍蜜月| 亚洲av成人精品一区久久| 亚洲精品一区av在线观看| 欧美黑人巨大hd| 亚洲三级黄色毛片| 欧美bdsm另类| 国产中年淑女户外野战色| 国产精品一区二区三区四区免费观看 | 成年女人毛片免费观看观看9| 国产视频一区二区在线看| 久久久久久国产a免费观看| 中出人妻视频一区二区| 日韩免费av在线播放| 69av精品久久久久久| 欧美一级a爱片免费观看看| 午夜福利18| 俺也久久电影网| 国产熟女xx| 草草在线视频免费看| 熟女人妻精品中文字幕| 欧美区成人在线视频| a级毛片免费高清观看在线播放| 91麻豆av在线| 国产三级中文精品| 高清毛片免费观看视频网站| 特级一级黄色大片| 丰满乱子伦码专区| 国产成人a区在线观看| 国产av在哪里看| 色精品久久人妻99蜜桃| 欧美乱色亚洲激情| 色哟哟·www| 校园春色视频在线观看| 精品人妻1区二区| 日韩高清综合在线| 国产精品国产高清国产av| 亚洲av成人av| 中文在线观看免费www的网站| 欧美又色又爽又黄视频| 久久久色成人| 精品不卡国产一区二区三区| 51午夜福利影视在线观看| 午夜精品一区二区三区免费看| 亚洲乱码一区二区免费版| 一本久久中文字幕| 黄色配什么色好看| 色综合站精品国产| 国内久久婷婷六月综合欲色啪| 成人国产一区最新在线观看| 久久九九热精品免费| 99国产精品一区二区三区| 欧美黑人欧美精品刺激| 久久精品国产亚洲av天美| 91午夜精品亚洲一区二区三区 | 老师上课跳d突然被开到最大视频 久久午夜综合久久蜜桃 | 亚洲国产色片| 网址你懂的国产日韩在线| 丰满乱子伦码专区| 免费观看精品视频网站| 久久久久久久久大av| 老司机午夜十八禁免费视频| 国产免费一级a男人的天堂| 性色av乱码一区二区三区2| 日本一本二区三区精品| 色综合亚洲欧美另类图片| 99热这里只有是精品在线观看 | 色视频www国产| 国产极品精品免费视频能看的| 国产伦人伦偷精品视频| 国产亚洲精品av在线| 宅男免费午夜| 精品久久久久久成人av| 国产午夜精品久久久久久一区二区三区 | 欧美一区二区精品小视频在线| 亚洲欧美日韩卡通动漫| 99久久成人亚洲精品观看| 动漫黄色视频在线观看| 亚洲精华国产精华精| 国产亚洲精品综合一区在线观看| 99视频精品全部免费 在线| 我要搜黄色片| 在线观看舔阴道视频| 欧美精品国产亚洲| 国产色爽女视频免费观看| av国产免费在线观看| 三级毛片av免费| 九九在线视频观看精品| 天天躁日日操中文字幕| 国产精品国产高清国产av| 久久久精品欧美日韩精品| 国产成人a区在线观看| 热99在线观看视频| 一卡2卡三卡四卡精品乱码亚洲| 一区二区三区高清视频在线| 久久久久国内视频| 一个人看的www免费观看视频| 一个人免费在线观看的高清视频| 丁香六月欧美| 哪里可以看免费的av片| 亚洲欧美日韩高清在线视频| 亚州av有码| 久久精品国产亚洲av天美| 日韩成人在线观看一区二区三区| 欧美色欧美亚洲另类二区| 国产免费一级a男人的天堂| 一区二区三区免费毛片| 精品福利观看| 嫩草影院新地址| 免费人成在线观看视频色| 欧美午夜高清在线| 高清在线国产一区| 草草在线视频免费看| 蜜桃亚洲精品一区二区三区| 国产午夜精品久久久久久一区二区三区 | 成人三级黄色视频| 欧美丝袜亚洲另类 | 国产一区二区亚洲精品在线观看| 亚洲欧美日韩高清在线视频| 欧美午夜高清在线| 精品人妻一区二区三区麻豆 | 一个人看的www免费观看视频| 亚洲av一区综合| 国产av麻豆久久久久久久| 97超视频在线观看视频| 最近最新中文字幕大全电影3| 男女下面进入的视频免费午夜| 少妇人妻精品综合一区二区 | 禁无遮挡网站| 在线天堂最新版资源| 天天躁日日操中文字幕| 国产精品98久久久久久宅男小说| 天天躁日日操中文字幕| 网址你懂的国产日韩在线| 精品免费久久久久久久清纯| 国产精品乱码一区二三区的特点| 天美传媒精品一区二区| 日本熟妇午夜| 亚洲七黄色美女视频| 91九色精品人成在线观看| 亚洲av.av天堂| 97超级碰碰碰精品色视频在线观看| 黄色一级大片看看| 国产精品,欧美在线| x7x7x7水蜜桃| 日韩免费av在线播放| 亚洲欧美日韩高清专用| 国产高潮美女av| 青草久久国产| 不卡一级毛片| 麻豆国产av国片精品| 日本黄色视频三级网站网址| 成年人黄色毛片网站| 国产精品亚洲一级av第二区| 18禁裸乳无遮挡免费网站照片| 国产黄片美女视频| 国产精品久久视频播放| 国产亚洲精品久久久久久毛片| 亚洲五月天丁香| 久久久久国产精品人妻aⅴ院| 日本免费a在线| netflix在线观看网站| 亚洲无线在线观看| 亚洲成av人片在线播放无| 九九热线精品视视频播放| 看免费av毛片| 有码 亚洲区| 中文字幕久久专区| 亚洲国产欧美人成| 成人精品一区二区免费| 乱人视频在线观看| 老司机深夜福利视频在线观看| 欧美一区二区亚洲| 亚洲最大成人中文| 久久亚洲真实| 99视频精品全部免费 在线| 欧美成人一区二区免费高清观看| 亚洲成人免费电影在线观看| 一本久久中文字幕| av在线蜜桃| 亚洲国产色片| 日韩精品青青久久久久久| 狂野欧美白嫩少妇大欣赏| 午夜福利高清视频| 很黄的视频免费| 人人妻,人人澡人人爽秒播| 午夜激情欧美在线| 亚洲自拍偷在线| 美女高潮的动态| 亚洲精品一区av在线观看| 欧美色欧美亚洲另类二区| 最好的美女福利视频网| 亚洲精品456在线播放app | 欧美一区二区亚洲| 欧美日韩瑟瑟在线播放| 精品久久久久久久末码| 久久精品91蜜桃| 欧美成狂野欧美在线观看| 永久网站在线| 18禁黄网站禁片午夜丰满| 999久久久精品免费观看国产| 久久中文看片网| 久久99热这里只有精品18| 日韩高清综合在线| 午夜免费男女啪啪视频观看 | 国产aⅴ精品一区二区三区波| 日韩欧美国产一区二区入口| 久久久精品欧美日韩精品| 一卡2卡三卡四卡精品乱码亚洲| 国产av在哪里看| 最新在线观看一区二区三区| 少妇被粗大猛烈的视频| 直男gayav资源| 国产精品一及| 国产精品电影一区二区三区| 最近视频中文字幕2019在线8| 国产亚洲精品av在线| 我要搜黄色片| 国语自产精品视频在线第100页| 日韩av在线大香蕉| 九九在线视频观看精品| 好男人在线观看高清免费视频| 91久久精品电影网| 欧美色欧美亚洲另类二区| 久久国产乱子伦精品免费另类| 精品午夜福利视频在线观看一区| www.色视频.com| 国产 一区 欧美 日韩| 亚洲精品色激情综合| 99久国产av精品| 亚洲精品一卡2卡三卡4卡5卡| 变态另类成人亚洲欧美熟女| 亚洲精品日韩av片在线观看| 亚洲成人久久爱视频| 日本成人三级电影网站| 亚洲av第一区精品v没综合| 欧洲精品卡2卡3卡4卡5卡区| 嫩草影视91久久| 男女视频在线观看网站免费| 麻豆av噜噜一区二区三区| 色尼玛亚洲综合影院| 日韩人妻高清精品专区| 免费大片18禁| 在线播放国产精品三级| 久久热精品热| 天美传媒精品一区二区| 亚洲av中文字字幕乱码综合| 亚洲av一区综合| 国产精品国产高清国产av| 中国美女看黄片| 不卡一级毛片| 欧美色欧美亚洲另类二区| 18禁黄网站禁片免费观看直播| 久久精品国产亚洲av天美| 成人一区二区视频在线观看| 丰满的人妻完整版| 免费人成在线观看视频色| 亚洲最大成人av| 日日摸夜夜添夜夜添av毛片 | 久久久色成人| av在线观看视频网站免费| 亚洲精品456在线播放app | 午夜老司机福利剧场| 精品一区二区三区人妻视频| xxxwww97欧美| 婷婷六月久久综合丁香| 免费在线观看日本一区| 欧美一区二区亚洲| av天堂中文字幕网| 欧美日韩福利视频一区二区| 日韩成人在线观看一区二区三区| 99久久成人亚洲精品观看| 少妇人妻精品综合一区二区 | 精品久久久久久久久久久久久| 高清日韩中文字幕在线| 麻豆一二三区av精品| 观看美女的网站| 黄色日韩在线| 精品欧美国产一区二区三| 亚洲精品在线观看二区| 欧美高清性xxxxhd video| 欧美黑人欧美精品刺激| 日日摸夜夜添夜夜添av毛片 | www.熟女人妻精品国产| 亚洲精品粉嫩美女一区| 国产伦一二天堂av在线观看| 久久久久国内视频| 嫩草影视91久久| 特大巨黑吊av在线直播| 亚洲av免费在线观看| 久久久久久久久中文| av视频在线观看入口| 成人特级黄色片久久久久久久| 欧美日韩福利视频一区二区| 婷婷色综合大香蕉| 精品一区二区三区av网在线观看| 99国产综合亚洲精品| 看十八女毛片水多多多| 麻豆国产av国片精品| 国产免费一级a男人的天堂| 国产亚洲av嫩草精品影院| 欧美一级a爱片免费观看看| 中文亚洲av片在线观看爽| 一区二区三区四区激情视频 | 久久香蕉精品热| 久久精品综合一区二区三区| 99热这里只有是精品50| 国产私拍福利视频在线观看| 别揉我奶头 嗯啊视频| 少妇被粗大猛烈的视频| 一级av片app| 日韩欧美国产一区二区入口| 麻豆成人午夜福利视频| 精品国产亚洲在线| а√天堂www在线а√下载| 亚洲无线观看免费| 午夜福利免费观看在线| av黄色大香蕉| 少妇丰满av| 色综合欧美亚洲国产小说| 欧美又色又爽又黄视频| 无人区码免费观看不卡| 国产精品影院久久| 国产久久久一区二区三区| 有码 亚洲区| 欧美日韩瑟瑟在线播放| 国产淫片久久久久久久久 | 非洲黑人性xxxx精品又粗又长| avwww免费| 成人一区二区视频在线观看| 亚洲欧美日韩卡通动漫| 成人av一区二区三区在线看| 亚洲欧美精品综合久久99| 88av欧美| 免费看光身美女| 久久午夜亚洲精品久久| 美女免费视频网站| 免费观看精品视频网站| 欧美zozozo另类| 91久久精品电影网| 国产精品久久电影中文字幕| 变态另类丝袜制服| 少妇高潮的动态图| 成人av在线播放网站| www日本黄色视频网| 亚洲av成人精品一区久久| 日韩欧美免费精品| 国产一区二区三区视频了| 免费看日本二区| 波多野结衣高清作品| 99国产精品一区二区三区| 午夜精品在线福利| 欧美在线黄色| 免费在线观看日本一区| 免费人成视频x8x8入口观看| 日韩免费av在线播放| 国产成人啪精品午夜网站| 国产亚洲欧美在线一区二区| 亚洲av二区三区四区| 午夜激情欧美在线| 亚洲av.av天堂| 中文资源天堂在线| 国产亚洲精品久久久com| 亚洲成人精品中文字幕电影| 亚洲在线观看片| 亚洲七黄色美女视频| 国产高潮美女av| 亚洲男人的天堂狠狠| 亚洲av日韩精品久久久久久密| av福利片在线观看| 欧美色欧美亚洲另类二区| 在线免费观看的www视频| 亚洲,欧美,日韩| 国产精品嫩草影院av在线观看 | 国产高清视频在线观看网站| 亚洲国产精品合色在线| 一进一出抽搐动态| 男女做爰动态图高潮gif福利片| 在线国产一区二区在线| 亚洲欧美清纯卡通| 18禁黄网站禁片免费观看直播| 99精品在免费线老司机午夜| 性插视频无遮挡在线免费观看| 欧美又色又爽又黄视频| 国产高清三级在线| 亚洲欧美日韩卡通动漫| 成人国产一区最新在线观看| 中文字幕人妻熟人妻熟丝袜美| av在线天堂中文字幕| 欧美三级亚洲精品| 欧美日韩亚洲国产一区二区在线观看| 琪琪午夜伦伦电影理论片6080| 又紧又爽又黄一区二区| 国产精品亚洲av一区麻豆| www.999成人在线观看| 伦理电影大哥的女人| 精品无人区乱码1区二区| 精品乱码久久久久久99久播| 少妇熟女aⅴ在线视频| 国产美女午夜福利| 宅男免费午夜| 欧美精品啪啪一区二区三区| 国产成人av教育| 宅男免费午夜| 757午夜福利合集在线观看| 51国产日韩欧美| 91麻豆精品激情在线观看国产| 熟妇人妻久久中文字幕3abv| 精品熟女少妇八av免费久了| 国产精品久久久久久精品电影| 亚洲,欧美,日韩| 精品人妻熟女av久视频| 五月伊人婷婷丁香| 国产精品一区二区免费欧美| 国产91精品成人一区二区三区| 午夜激情欧美在线| 激情在线观看视频在线高清| 一级毛片久久久久久久久女| 一级黄色大片毛片| 男人和女人高潮做爰伦理| 国产爱豆传媒在线观看| 成人鲁丝片一二三区免费| 亚洲美女视频黄频| 中文字幕久久专区| 日本免费a在线| 中文在线观看免费www的网站| 变态另类丝袜制服| 日本熟妇午夜| a级毛片a级免费在线| 国产免费男女视频| 91久久精品国产一区二区成人| 日本黄色视频三级网站网址| 免费在线观看亚洲国产| 少妇被粗大猛烈的视频| av在线老鸭窝| 九九热线精品视视频播放|