• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Quasi in-situ EBSD analysis of twinning-detwinning and slip behaviors in textured AZ31 magnesium alloy subjected to compressive-tensile loading

    2022-07-12 10:28:44YuzhiZhuDewenHouQizhenLi
    Journal of Magnesium and Alloys 2022年4期

    Yuzhi Zhu, Dewen Hou, Qizhen Li,*

    aSchool of Mechanical and Materials Engineering, Washington State University, Pullman, WA 99164, United States

    b Micron School of Materials Science and Engineering, Boise State University, Boise 83725-1030 ID, United States

    Abstract Twinning and detwinning behavior, together with slip behavior, are studied in a textured AZ31 magnesium alloy under compressive and tensile strains along the rolling direction (RD) after each interrupted mechanical test via quasi in-situ electron backscattered diffraction technique.The results show that twinning firstl takes place under the compressive strain along the RD.With the increasing compressive strain, {10ˉ12} tensile twins firstl nucleate, then propagate, and finall thicken.While under a reversed tensile strain along the RD, detwinning occurs.No nucleation happens during detwinning.Thus, tensile twins can detwin at lower tensile strain, followed by thinning, shortening,and vanishing.Slips are also activated to accommodate the plastic deformation.In the matrix, prismatic slip can only dominate at relatively high strains.Otherwise, basal slip dominates.While in the twins, prismatic slip can activate at lower strains, which is ascribed to the texture reorientation.

    ? 2021 Chongqing University.Publishing services provided by Elsevier B.V.on behalf of KeAi Communications Co.Ltd.

    This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/)

    Peer review under responsibility of Chongqing University

    Keywords: Magnesium alloy; Twinning; Detwinning; Prismatic slip; quasi in-situ EBSD.

    1.Introduction

    Twinning and detwinning play an important role in plastic deformation for hcp structure materials [1, 2], as hexagonal materials cannot offer enough numbers of slip systems during deformation[3-6].The most common and easily activated twinning mode in magnesium alloys is {10ˉ12} tensile twinning at room temperature [7-10].Tensile twinning can only be activated under c-axis extension [11-13].Consequently, it should exhibit an asymmetric deformation behavior on a textured magnesium alloy, i.e., rolled or extruded material, with a lower yield strength under compression and a higher yield strength under tension [14-17].

    Generally,detwinning of the{10ˉ12}tensile twins can occur under two loading conditions:(1)reloading along the opposite direction after the pre-loading; and (2) re-compression along the orthogonal direction after the pre-compression along the RD [18-22].Therefore, twinning and detwinning usually can be observed when cyclic loadings are applied.With a limited number of fatigue cycles, the deformation was mainly dominated by twinning/detwinning mode [23, 24].Furthermore, the fracture morphology was controlled by the repeated twinning-detwinning process [25].The twinning/detwinning under different strain paths can lead to different mechanical responses [26, 27].Pre-compressive deformation usually caused a drop in the tensile yield strength [28, 29].Previous research reported that the activation of detwinning increased the work hardening rate [23, 30].It was also found that not only twinning-slip interaction but twinning-detwinning activity could result in the Bauschinger effect, due to the stress relaxation during the detwinning process [31-33].

    The main explanation of the twinning-detwinning behavior is that the process is controlled by the migration of twin boundaries (TBs) [34-36].Compared to the twinning nucle-ation process, the propagation process needs much lower energy,i.e.,CRSSnucleation>CRSSpropagation[37].Moreover,the process of detwinning does not need nucleation [38, 39].As a result, detwinning can take place under a stress even lower than the CRSS for twin growth, which is attributed to the internal stress in the grain matrix generated during twinning.It was reported that CRSS values for {10ˉ12} tensile twinning and detwinning in wrought ZK60A alloys are 15 MPa and 6 MPa, respectively [40].

    Besides the twinning and detwinning mechanisms, there should be the activations of slips to accommodate the plastic deformation.The different activations of slips, twinning,and detwinning during the loading path change should be responsible for the asymmetric deformation behaviors [41, 42].Several simulation results suggested that during the loading path change process,the activities of the slip systems changed both in the matrix and the twins due to the texture reorientations [43-45].Hama et al.[44]suggested that during the reloading process under tension, there was a transfer from the detwinning-dominated mode to the slip-dominated mode as the tensile strain increased.Wang et al.[45]found increased activation of the prismatic slip system during the reversed shear loading under cyclic shear.However, there is a lack of experimental study on slip behaviors during the loading path change process.

    To date, the twinning-detwinning phenomenon was observed to take place under cyclic loading or different strain paths.However, there is still a lack of study focusing on the twinning-detwinning behaviors, associated with the twinning/detwinning-slip interactions during the loading path change in rolled AZ31 magnesium alloy.The purpose of this paper is to understand the evolution of twinning/detwinning,as well as the dislocation slips, subjected to two cycles of compressive-tensile loadings along the RD in a textured AZ31 magnesium alloy sheet.The microstructure and texture evolutions were investigated by the quasi in-situ EBSD technique.

    2.Experimental methods

    A commercial rolled AZ31 magnesium alloy with a thickness of 20 mm was used in this study.The specimen with a dog-bone shape was cut from the as-received rolled AZ31 magnesium alloy using an electrical discharge machine, with a gage length of 8 mm (RD), a thickness of 10 mm (ND),and a width of 4 mm (TD).Here, RD, ND, and TD represent rolling direction, normal direction, and transverse direction, respectively.Mechanical tests were carried out in a CMT 5150 machine.Both tensile and compression tests were processed along the RD at room temperature with a strain rate of 10-3s-1.Mechanical tests were interrupted at certain deformation strains to obtain the mechanical responses and evaluate the microstructure evolution of the AZ31 magnesium specimen.

    Fig.1.Compressive and tensile stress-strain curves along the RD to different strain levels.

    Electron back-scattered diffraction (EBSD) measurements were performed in a JOEL-JEM 7800F fiel emission scanning electron microscope (SEM) equipped with Aztec and HKL Channel 5 software.The scanning step size is 0.7 μm.The deformed specimen for EBSD measurement was mechanically polished, followed by electrochemical polishing with AC2 solutions.EBSD measurements were carried out in the sample at a certain region parallel to the RD-TD plane after each deform stage.

    3.Results and discussion

    3.1.Mechanical behaviors

    The successive deformation stress-strain curves are exhibited in Fig.1, including compression and tension along the RD to different strain levels.The stress-strain curve above the x-axis in the diagram represents the tensile test, and the curve below the x-axis represents the compression test.The sample initially deformed under two successive compression tests (denoted as CL1 and CL2) with a pre-strain of 1.3%and 3.2%, respectively, in the firs compression stage.It is observed that the compressive stress-strain curve contains a yield plateau, which indicates the tensile twinning activation during the compression test with the deformation load perpendicular to the c-axis [46, 47].In the firs tension stage, the pre-strained sample was then deformed under tensile loading to strains of 1.6%,4.8%,7.6%,11%,and 14.6%,respectively.The tensile stress-strain curves (denoted as TL1, TL2, TL3,TL4, and TL5, respectively) show similar deformation behaviors that all exhibit a typical convex shape.An increment of the yield strength after each tensile deformation can be observed.This increment can result from the strain hardening effect during the deformation, where tangled dislocations prevent further dislocation movements [48].After then, at the second compression stage, a compressive deformation with a strain of 0.9%, was conducted.A similar stress-strain curve(denoted as CL3) is plotted as those in the firs compression stage, indicating the similar deformation mode activations in this deformation stage.Finally, in the second tension stage, two steps of the successive tension deformations (de-noted as TL6 and TL7, respectively) were carried out.The tensile strains can be clarifie as 1.6% and 4%, respectively.

    Fig.2.EBSD inverse pole figur (IPF) maps, misorientation angle distributions, and {0001} pole figure for the rolled AZ31 magnesium alloy sample: (a)the initial state; (b) pre-compressed to 1.3% along the RD; (c) pre-compressed to 3.2% along the RD.

    3.2.Microstructure evaluation after each deform stage

    Figure 2 presents the IPF maps, the misorientation angle profiles and the {0001} pole figure to illustrate the initialstate microstructure and the microstructure evolutions of the sample compressed to the pre-strain of 1.3% (CL1) and 3.2%(CL2), respectively.Figure 2a shows the initial microstructure and texture of the textured AZ31 magnesium alloy.The sample exhibits an equiaxed grain structure with the grain size ranging from ~5 to ~50 μm in the IPF map.No twins are detected in the initial microstructure.The boundary misorientation angle distribution ranges from 10 to 60°, which indicates that the predominant boundaries in the initial-state sample are high angle grain boundaries (HAGBs).In this work,HAGBs are define as grain boundaries with a misorientation angle greater than 15° and low angle grain boundaries(LAGBs) contain a misorientation angle from 2 to 15° The{0001} pole figur in Fig.2a reveals that the initial state sample has a typical basal texture that the c-axis of the unit cell is parallel to the ND.Figure 2b shows the microstructure of the sample at 1.3% pre-compressive strain along the RD.Many twins newly appeared in the matrix grains as can be seen in the IPF map.After CL1, two peaks, ranging from 2 to 15° and 80-90°, generate in the misorientation angle distribution histogram.The peaks ranging from 2 to 15° result from the generation of the LAGBs during compression.While the peaks ranging from 80 to 90° are attributed to the activation of the twin lamellae, which is consistent with the result in the IPF map in Fig.2b.Furthermore, it indicates that the active twins are of {10ˉ12} type, as the misorientation angle tilts ~86.3°.It is known that {10ˉ12} tensile twins are easily activated under compressive strain perpendicular to or under tensile strain parallel to the c-axis of the HCP lattice [49].An increase of the twinning component and a decrease of the basal component can be observed from the{0001}pole figur in Fig.2b.Figure 2c shows the microstructure of the sample at 3.2% compression strain.Twinning took place in nearly all matrix grains with a soft orientation.The existing {10ˉ12}tensile twins continued propagating, thickening, and further coalesced at the CL2 stage, leading to the disappearance of some twin boundaries.Thus, the peaks of the grain boundary misorientation angle ranging from 80 to 90°, as can be seen, decrease slightly due to the coalescence of the existing twin lamellae.While the texture changed little under CL2, as shown in the pole figur in Fig.2b.

    Fig.3.EBSD inverse pole figur (IPF) maps, misorientation angle distributions, and {0001} pole figure of the AZ31 magnesium alloy under reversed tension loading: (a) reversely tension to 1.6%; (b) reversely tension to 4.8%; (c) reversely tension to 7.6%; (d) reversely tension to 11%; (e) reversely tension to 14.6%.

    Figure 3 exhibits the IPF maps, the misorientation angle distributions, and the {0001} pole figure for the pre-strained sample deformed after successive reversed tensile loadings along the RD.The detwinning phenomenon is observed during the deformation process.In Fig.3a, when a 1.6% tensile strain (TL1) was applied to the pre-compressed sample,no significan change in the microstructure can be observed.Moreover, when the applied strain increased to 4.8% (TL2),nearly all {10ˉ12} tensile twins became thinner, as seen in the IPF map in Fig.3b.Additionally, some extremely thin twin lamellae disappeared.In the misorientation angle distribution profile the peaks ranging from 80 to 90° increase, since the coalesced twins started to disperse, and new twin boundaries were generated.As can be observed in the {0001} pole fig ure (Fig.3b) for the sample at TL2, the basal pole also tilts slightly back to the ND.In Fig.3c and d, as the tensile strain increased from 7.6% (TL3) to 11% (TL4), twin lamellae continued to become thinner and shorter.Finally, only several twin lamellae vanished.The distributions of the grain boundary misorientation angle and the textures after TL3 and TL4 do not change too much.In Fig.3e, when the reversed tensile strain was up to 14.6% (TL5), nearly all the {10ˉ12}tensile twins vanished, but only several extremely thin twin lamellae remained.The remaining thin twin lamellae may result from the incomplete reversed tensile deformation.From the grain boundary misorientation angle histogram, the peaks ranging from 80 to 90° decrease drastically, consistent with the microstructure observation that almost fully detwinning occurred in all matrix grains.While the peaks ranging from 2 to 15° increase.It is suggested that twin boundaries are replaced by LAGBs during detwinning [50].As seen from the {0001} pole figur in Fig.3e, the basal pole tilts back to the ND.More specificall , the reversed tensile loading along RD renders c-axis re-aligning perpendicular to the ND, while the pre-formed tensile twins from compression disappear.As reported in the previous study, the mechanism of detwinning can be considered as the reversed process of twinning [35,51].It is known that the twinning propagation is controlled by the movement of TBs [52].TBs consist of coherent twin boundaries(CTBs),basal-prismatic(BPs),and prismatic-basal(PBs) facets.The evolution of twinning/detwinning then can be considered as the glide or climb of twinning dislocations along these interfaces,resulting in the migration of TBs.Consequently, the residual twins become thinner and shorter.

    Figure 4 shows the IPF maps, the distribution of misorientation angle,and the{0001}pole figure for the sample under a repeated process of compression and tension.In Fig.4a,under re-compression with a 0.9% strain (CL3), a limited number of thin twin lamellae nucleated.While there is no signifi cant growth of the existing tensile twins.In the misorientation angle distribution histogram, the consistent results can be observed that the peaks ranging from 80 to 90°increase slightly.It is also found that re-twinning at the CL3 stage takes place at the same locations as that in the pre-compression stage.A similar phenomenon of the second-generation twin was observed in pure Mg under cyclic loading via in-situ TEM [53].It might be explained that twinning prefers to nucleate at specifi sites.Figure 5b shows the detwinning phenomenon under the reversed 1.6% tensile strain (TL6).Due to the limited tensile strain, only several thin twins became narrower.No significan change can be observed neither from the grain boundary misorientation angle distribution nor from the{0001}pole figure As the tensile strain increased to 4% (TL7), most of the residual twin lamellae vanished, as can be observed from the IPF map in Fig.4c.At the same time, in the misorientation angle distribution histogram, the peaks ranging from 80 to 90° decrease to nearly zero, while the fraction of the LAGBs increase.The {0001} pole figur shows a basal texture with only a small fraction of the c-axis distributed away from the ND.

    Fig.4.EBSD inverse pole figur (IPF) maps, misorientation angle distributions, and {0001} pole figure of the AZ31 magnesium alloy under repeated compression and tension loading: (a) compression to 0.9%; (b) reversely tension to 1.6%; (c) reversely tension to 4%.

    To study the interactions between twining and slip, the ingrain misorientation axis (IGMA) analysis, associated with the Schmid factor (SF) analysis was applied.Theoretically,the activation of slips can cause lattice rotations, which in term can be detected by electron backscattered diffraction.The detailed in-grain misorientation axis distribution method is introduced by Chun et al.[54, 55].For each slip system in magnesium, they tilt around a certain axis (also named as Taylor axis).Namely, the {0002}〈11ˉ20〉 basal slip, the{10ˉ10}〈11ˉ20〉 prismatic slip, and the {11ˉ22}〈11ˉ2ˉ3〉 pyramidal slip have the 〈0ˉ110〉, 〈0001〉, and 〈1ˉ100〉 Taylor axis, respectively.Therefore, the identification of the slip types both in the matrix and the twins can be studied via the IGMA method.The IGMA distributions during the twinning and detwinning process in four selected twinned/untwined grains are calculated.The misorientation angle concerned in this work is from 0.5° to 2°.And to obtain accurate results, only matrix and twins with more than 400 measured points are chosen.Figure 5 shows the IGMA distribution of four selected grains in rolled AZ31 magnesium alloy under repeated compression and tension loadings along the RD.The selected matrix grains and twins are marked as M1~M4 and T2~T4, respectively.The loading condition and the maximum/minimum intensity are given at the top-left corner of each figure Table 1 shows the SF calculations for grains illustrated in Fig.5.

    Figure 5a shows the IGMA distributions in an untwined grain (marked as M1).The IGMA distributions are mainly concentrated around 〈uvt0〉 directions.As mentioned above,the<uvt0>-type rotation results from the activation of 〈a〉type basal and 〈c+a〉 type pyramidal slips.Considering the high CRSS for<c+a>type pyramidal slip and the relatively low Schmid factor (SF) values shown in Table 1, the activation of〈c+a〉type dislocations is difficult It can be assumed that in M1 during the repeated compression and tension loadings, the dominant slip mode is always the 〈a〉 type basal slip.Figure 5b exhibits the IGMA distributions in a twinned grain,where the matrix is marked as M2, and the twin is marked as T2.Similarly, during the pre-compression process (CL1 and CL2), the axis distributions in the matrix M2 are concentrated around〈uvt0〉directions.Under the reversed tension along the RD, from TL1 to TL4, the IGMA distribution is focused around the 〈uvt0〉 axis.As the tensile strain increased to 14.6% (shown in TL5) during the detwinning process, the maximum intensity of the IGMA in the matrix rotates around the〈0001〉axis.It is proposed that〈a〉type prismatic slips are more favorable at the TL5 stage.Consistently, the SF valuefor prismatic slip in M2 is the highest,which means prismatic slip should be easily activated when the applied stress is high enough.Next, under the repeated relatively low compressive and tensile strains, the maximum intensities are around the〈uvt0〉 axis.The slip behaviors in the twin T2 are different from that in the matrix M2.During the whole loading process, including the twinning and the detwinning process,the lattice rotation distributions are concentrated around the〈uvt0〉 axis, indicating either 〈a〉 type basal or 〈c+a〉 type pyramidal slip dominates.According to the SF calculations in Table 1, during the twinning process, 〈c+a〉 type pyramidal slip possesses the highest SF value, while during the detwinning process, 〈a〉 type basal slip is more favorable.In Fig.5c,the IGMA distributions in the matrix M3 and the twin T3 are presented.In M3, the maximum intensities of the IGMA are mostly around the 〈uvt0〉 axis, which suggests that during the whole process, 〈a〉 type basal and 〈c+a〉 type pyramidal slips are favorable.At the CL2 stage, the IGMA distribution spread out towards the 〈0001〉 direction, indicating the activation of〈a〉type prismatic slip,which is consistent with the SF calculation shown in Table 1.During the twinning process,the IGMA distributions in the twin T3 are concentrated in the〈uvt0〉direction.Considering the lowest CRSS and the second highest SF value (in Table 1), it is reasonable to say 〈a〉 type basal slips are dominant in T3.While during the detwinning process,as the tensile strain increased to 7.5%,the IGMA distribution concentrations tilt from the 〈uvt0〉 direction to the〈0001〉 direction.And the SF value for prismatic slip is the highest.Therefore, 〈a〉 type prismatic slips are activated.The twinning/detwinning operation, which re-orientates the grains with a hard orientation for slip, contributes to the prismatic slip activation.Figure 5d shows the IGMA distributions in the matrix M4 and the twin T4.Similarly, the maximum intensities of M4 are around the 〈uvt0〉 axis during the whole deformation process.According to the SF results, both 〈a〉type basal and 〈c+a〉 type pyramidal slips are favorable.The IGMA distribution in T4 at 1.3% pre-compressive strain is concentrated around the 〈uvt0〉 direction.While as the prestrain increased to 3.2%, the IGMA distribution rotates to the〈0001〉 direction, suggesting that the 〈a〉 type prismatic slips dominate at this stage.At the TL1 stage (ε=1.6%), prismatic slip is still preferred in T4.While as the reversed tensile strain increased to 4.8%and higher,the IGMA distribution concertation transfers to the 〈uvt0〉 direction.Because at these stages,the twin T4 vanishes very quickly, we assume the twin size can also affect the slip activations [56].

    Table 1Schmid factors for grains illustrated in Fig.5.

    Fig.5.The in-grain misorientation axis (IGMA) distributions of selected grains in AZ31 magnesium alloy under repeated compression and tension loadings.The maximum/minimum intensities of the IGMA distributions are given at the top of each figure

    4.Conclusions

    In this work, the quasi in-situ electron backscattered diffraction technique was used to study the twinning and detwinning behaviors on a rolled AZ31 magnesium alloys under compression and tension along the RD after interrupted mechanical tests.The slip behavior analysis was conducted by the in-grain misorientation axis distribution method and Schmid factor method.Pre-compression tests revealed that{10ˉ12} tensile twins nucleated at low compressive strains,then further propagated and thickened with increasing strains.The microstructure evolution during reversed tensile tests along the RD exhibited the detwinning process.At a relatively low reversed tensile strain, the existing tensile twins started to become thinner.With the increasing reversed strain, twins continued thinning, shortening, and finall vanishing.Under repeated compressive and tensile loadings along the RD, retwinning and re-detwinning occurred.It was also observed that re-twinning preferred to take place at the same location as in the firs deformation stage.The IGMA analysis showed that the slip behaviors in the matrix and the twins were different.In the matrix, at low stains, 〈a〉 type basal slip was favorable.As the stain increase, it was hard to fin 〈a〉 type prismatic slips that could dominate in the matrix.In the twins,since the texture reorientation took place,prismatic slips could be activated more easily, even at relatively low strains.

    Declaration of Competing Interest

    None.

    Acknowledgment

    The authors gratefully acknowledge the financia support from the US Department of Energy, Offic of Basic Energy Science under Award no.DE-SC0016333.

    一级黄片播放器| 热99re8久久精品国产| 欧美黄色淫秽网站| 国产伦精品一区二区三区四那| 亚洲成人免费电影在线观看| 黄片小视频在线播放| 欧美在线一区亚洲| 色尼玛亚洲综合影院| 搞女人的毛片| 无遮挡黄片免费观看| a级毛片a级免费在线| 在线观看美女被高潮喷水网站 | 国产精品久久久久久亚洲av鲁大| 免费一级毛片在线播放高清视频| 看片在线看免费视频| 女同久久另类99精品国产91| 亚洲激情在线av| 一区二区三区四区激情视频 | 日本免费一区二区三区高清不卡| 深夜a级毛片| 黄色视频,在线免费观看| 熟女人妻精品中文字幕| 亚洲av中文字字幕乱码综合| 97碰自拍视频| 亚洲av美国av| 久久性视频一级片| 国产精品电影一区二区三区| 久久久久亚洲av毛片大全| 色哟哟·www| 亚洲av免费高清在线观看| 日韩欧美国产在线观看| 国产一级毛片七仙女欲春2| 国产精品免费一区二区三区在线| 亚洲欧美清纯卡通| 老师上课跳d突然被开到最大视频 久久午夜综合久久蜜桃 | www日本黄色视频网| 深爱激情五月婷婷| 欧美日韩亚洲国产一区二区在线观看| 国产黄片美女视频| 黄片小视频在线播放| www.www免费av| www.熟女人妻精品国产| 永久网站在线| 亚洲国产欧洲综合997久久,| 国内精品久久久久久久电影| 国产探花极品一区二区| 亚洲国产精品sss在线观看| 极品教师在线免费播放| 欧美另类亚洲清纯唯美| 国产视频一区二区在线看| 色综合亚洲欧美另类图片| 一个人观看的视频www高清免费观看| 特大巨黑吊av在线直播| 欧美绝顶高潮抽搐喷水| av欧美777| 久久亚洲真实| 亚洲精品乱码久久久v下载方式| 黄色一级大片看看| 丰满的人妻完整版| 男插女下体视频免费在线播放| 中文在线观看免费www的网站| 三级男女做爰猛烈吃奶摸视频| 婷婷六月久久综合丁香| 国产亚洲av嫩草精品影院| 欧洲精品卡2卡3卡4卡5卡区| 亚洲经典国产精华液单 | 又黄又爽又刺激的免费视频.| 少妇熟女aⅴ在线视频| 精品人妻视频免费看| 亚洲七黄色美女视频| 特大巨黑吊av在线直播| 国产亚洲精品久久久久久毛片| 一进一出好大好爽视频| 一级作爱视频免费观看| 99久久精品一区二区三区| 中文亚洲av片在线观看爽| 久久99热这里只有精品18| 18美女黄网站色大片免费观看| 国产久久久一区二区三区| 国产乱人伦免费视频| 九九久久精品国产亚洲av麻豆| 一个人免费在线观看的高清视频| 久久久色成人| 成人欧美大片| 亚洲专区国产一区二区| 久久精品久久久久久噜噜老黄 | 国产在视频线在精品| 国产毛片a区久久久久| 自拍偷自拍亚洲精品老妇| 亚洲av成人不卡在线观看播放网| 观看免费一级毛片| 国产精品电影一区二区三区| 91在线观看av| 黄色一级大片看看| 12—13女人毛片做爰片一| 波多野结衣高清作品| 国产乱人视频| 搡女人真爽免费视频火全软件 | 一级av片app| 赤兔流量卡办理| 亚洲精品一区av在线观看| 搡老妇女老女人老熟妇| 天堂影院成人在线观看| 嫩草影视91久久| 嫩草影院精品99| 性欧美人与动物交配| 黄色配什么色好看| 天堂动漫精品| 欧美xxxx性猛交bbbb| 最近最新中文字幕大全电影3| 国产探花在线观看一区二区| 性色avwww在线观看| 在线看三级毛片| 日韩欧美在线乱码| 97碰自拍视频| 日本精品一区二区三区蜜桃| 嫁个100分男人电影在线观看| 欧美中文日本在线观看视频| 在线播放无遮挡| 午夜福利高清视频| 久久人人爽人人爽人人片va | 成年女人毛片免费观看观看9| 亚洲欧美日韩高清在线视频| 成年女人看的毛片在线观看| 午夜福利欧美成人| 丝袜美腿在线中文| 精品99又大又爽又粗少妇毛片 | 国产乱人伦免费视频| 日韩中字成人| 国产精品女同一区二区软件 | 精品久久久久久成人av| 国产毛片a区久久久久| 亚洲美女黄片视频| 国产一区二区在线av高清观看| 18禁裸乳无遮挡免费网站照片| 亚洲人成网站在线播| 欧美不卡视频在线免费观看| 搡老岳熟女国产| 免费看美女性在线毛片视频| 一进一出抽搐动态| 国产大屁股一区二区在线视频| 看黄色毛片网站| 欧美三级亚洲精品| 亚洲成人中文字幕在线播放| 十八禁网站免费在线| 午夜亚洲福利在线播放| 一本一本综合久久| 欧美成人免费av一区二区三区| 中文在线观看免费www的网站| 久久久久免费精品人妻一区二区| 成人特级黄色片久久久久久久| 18禁黄网站禁片免费观看直播| 亚洲18禁久久av| 欧美zozozo另类| 亚洲美女搞黄在线观看 | 在线观看舔阴道视频| 免费看a级黄色片| 免费观看人在逋| 高清在线国产一区| 国产男靠女视频免费网站| 91久久精品国产一区二区成人| 亚洲人成网站高清观看| 中文字幕人成人乱码亚洲影| 亚洲成人久久爱视频| 国产免费男女视频| 久久人人爽人人爽人人片va | 亚洲成人免费电影在线观看| 天美传媒精品一区二区| 成人欧美大片| 亚洲综合色惰| 首页视频小说图片口味搜索| 12—13女人毛片做爰片一| 国内毛片毛片毛片毛片毛片| 国产色爽女视频免费观看| 久久欧美精品欧美久久欧美| 国产精品久久视频播放| 亚洲国产日韩欧美精品在线观看| 久久亚洲精品不卡| 免费在线观看亚洲国产| 999久久久精品免费观看国产| 亚洲最大成人av| 能在线免费观看的黄片| 国产精品不卡视频一区二区 | 国内久久婷婷六月综合欲色啪| 日本黄大片高清| 极品教师在线免费播放| 观看免费一级毛片| 一a级毛片在线观看| 1024手机看黄色片| 一个人看视频在线观看www免费| 色综合亚洲欧美另类图片| 国产成人aa在线观看| 欧美激情国产日韩精品一区| 十八禁网站免费在线| 国产单亲对白刺激| 午夜福利高清视频| 亚洲五月婷婷丁香| 欧美激情久久久久久爽电影| a级毛片免费高清观看在线播放| 欧美高清性xxxxhd video| 成人毛片a级毛片在线播放| 在线观看美女被高潮喷水网站 | 久久人人精品亚洲av| 久久久久国内视频| 成人欧美大片| 在线免费观看的www视频| 成年免费大片在线观看| 成人特级黄色片久久久久久久| 99国产综合亚洲精品| 日韩欧美国产在线观看| 精品国产亚洲在线| 美女免费视频网站| 91狼人影院| 永久网站在线| 99久久精品热视频| 69av精品久久久久久| 非洲黑人性xxxx精品又粗又长| 久久精品综合一区二区三区| 午夜老司机福利剧场| 女人被狂操c到高潮| 国产成+人综合+亚洲专区| av天堂在线播放| 久久精品综合一区二区三区| 国产麻豆成人av免费视频| 精品一区二区三区av网在线观看| 久久国产精品影院| av国产免费在线观看| 国内毛片毛片毛片毛片毛片| 欧美丝袜亚洲另类 | 久久伊人香网站| 国产视频一区二区在线看| 99热只有精品国产| 麻豆成人午夜福利视频| 亚洲中文日韩欧美视频| 国产高清视频在线观看网站| 午夜福利成人在线免费观看| 好男人电影高清在线观看| 久久久久国内视频| 99久久九九国产精品国产免费| 久久久久久久午夜电影| 亚洲三级黄色毛片| www.色视频.com| 欧美3d第一页| 男人舔奶头视频| 男插女下体视频免费在线播放| 两性午夜刺激爽爽歪歪视频在线观看| 亚洲国产欧美人成| 一本精品99久久精品77| 久久亚洲精品不卡| 婷婷丁香在线五月| 村上凉子中文字幕在线| 亚洲人与动物交配视频| 日韩欧美 国产精品| 嫩草影院入口| 欧美日韩瑟瑟在线播放| 免费大片18禁| netflix在线观看网站| 国产成年人精品一区二区| 亚洲av电影不卡..在线观看| 亚洲国产精品999在线| 好男人在线观看高清免费视频| 国产精品一区二区三区四区免费观看 | 中文字幕久久专区| 亚洲激情在线av| 亚洲第一欧美日韩一区二区三区| 97碰自拍视频| 国产美女午夜福利| 久久精品91蜜桃| 两个人视频免费观看高清| 亚洲av中文字字幕乱码综合| 国产av不卡久久| 亚洲第一电影网av| 亚洲国产精品sss在线观看| 国产美女午夜福利| 一进一出抽搐gif免费好疼| 97热精品久久久久久| 一本综合久久免费| 国产一区二区三区在线臀色熟女| 成人一区二区视频在线观看| 一二三四社区在线视频社区8| 丰满人妻熟妇乱又伦精品不卡| 无遮挡黄片免费观看| 国产成人aa在线观看| 夜夜看夜夜爽夜夜摸| 91久久精品国产一区二区成人| 韩国av一区二区三区四区| 国产黄a三级三级三级人| 精品人妻一区二区三区麻豆 | 国产免费男女视频| 免费大片18禁| 国产伦在线观看视频一区| 99在线人妻在线中文字幕| 亚洲天堂国产精品一区在线| 99久久精品热视频| 别揉我奶头 嗯啊视频| 亚洲乱码一区二区免费版| 能在线免费观看的黄片| 久久久久久九九精品二区国产| 俺也久久电影网| 激情在线观看视频在线高清| 18禁在线播放成人免费| 日韩欧美在线乱码| or卡值多少钱| 国产亚洲精品av在线| 国产三级黄色录像| 免费人成在线观看视频色| 亚洲,欧美精品.| 亚洲久久久久久中文字幕| 国产午夜精品久久久久久一区二区三区 | 国产精品影院久久| 欧美xxxx性猛交bbbb| 日本黄大片高清| 日韩欧美精品免费久久 | 男人和女人高潮做爰伦理| 亚洲经典国产精华液单 | 身体一侧抽搐| 欧美成狂野欧美在线观看| 三级男女做爰猛烈吃奶摸视频| 91在线精品国自产拍蜜月| netflix在线观看网站| 国产一区二区在线av高清观看| 国产在线精品亚洲第一网站| 日本精品一区二区三区蜜桃| 怎么达到女性高潮| 亚洲熟妇中文字幕五十中出| 99热精品在线国产| 女生性感内裤真人,穿戴方法视频| 精品一区二区三区av网在线观看| 亚洲,欧美精品.| 级片在线观看| 美女黄网站色视频| 国产在线精品亚洲第一网站| 天堂动漫精品| 欧美最黄视频在线播放免费| 女生性感内裤真人,穿戴方法视频| 午夜精品一区二区三区免费看| 一夜夜www| 久久久久免费精品人妻一区二区| 一级毛片久久久久久久久女| 国产熟女xx| 噜噜噜噜噜久久久久久91| 真人做人爱边吃奶动态| 国产三级黄色录像| 99久久99久久久精品蜜桃| 亚洲精品粉嫩美女一区| 真人做人爱边吃奶动态| 舔av片在线| 欧美高清成人免费视频www| 国产精品日韩av在线免费观看| 国产精品电影一区二区三区| 色综合站精品国产| 欧美日本视频| 国产精品女同一区二区软件 | 波多野结衣高清无吗| 国产麻豆成人av免费视频| 国内少妇人妻偷人精品xxx网站| 久久久国产成人免费| 亚洲国产高清在线一区二区三| 色精品久久人妻99蜜桃| 全区人妻精品视频| 欧美成狂野欧美在线观看| 亚洲精品在线美女| 日韩亚洲欧美综合| 中文字幕av成人在线电影| 精品熟女少妇八av免费久了| 国产三级中文精品| 欧美黄色淫秽网站| 国产真实伦视频高清在线观看 | 日韩精品中文字幕看吧| 亚洲av熟女| 欧美日韩国产亚洲二区| 国产高清视频在线观看网站| 精品午夜福利视频在线观看一区| 不卡一级毛片| 色哟哟·www| 色av中文字幕| 757午夜福利合集在线观看| 亚洲成av人片在线播放无| 精品人妻视频免费看| 中国美女看黄片| 国产精品不卡视频一区二区 | 无人区码免费观看不卡| 白带黄色成豆腐渣| 亚洲无线在线观看| 亚洲第一电影网av| 2021天堂中文幕一二区在线观| 男人的好看免费观看在线视频| 搡老熟女国产l中国老女人| 美女高潮喷水抽搐中文字幕| 欧美3d第一页| 每晚都被弄得嗷嗷叫到高潮| 两个人视频免费观看高清| 欧美潮喷喷水| 99久久精品热视频| 国产亚洲欧美98| 亚洲电影在线观看av| 色播亚洲综合网| 99久久精品一区二区三区| 黄色女人牲交| 黄色丝袜av网址大全| 欧美精品啪啪一区二区三区| 国产高清有码在线观看视频| h日本视频在线播放| 久久久久国内视频| 两个人的视频大全免费| 免费在线观看亚洲国产| 3wmmmm亚洲av在线观看| 午夜久久久久精精品| 亚洲自偷自拍三级| 亚洲中文日韩欧美视频| 69人妻影院| 网址你懂的国产日韩在线| 欧美成人一区二区免费高清观看| av在线蜜桃| 三级毛片av免费| 日本五十路高清| 国产成人av教育| 亚洲欧美日韩东京热| 亚洲av.av天堂| 很黄的视频免费| av福利片在线观看| 免费大片18禁| 国产激情偷乱视频一区二区| av欧美777| 免费在线观看亚洲国产| 亚洲色图av天堂| 亚洲狠狠婷婷综合久久图片| 日韩成人在线观看一区二区三区| 精品人妻1区二区| 国产精品一区二区三区四区久久| 亚洲无线在线观看| 中文字幕久久专区| 精品乱码久久久久久99久播| 美女被艹到高潮喷水动态| 99久久精品热视频| av在线老鸭窝| 国产亚洲欧美在线一区二区| 国产欧美日韩精品一区二区| 极品教师在线免费播放| 又黄又爽又免费观看的视频| 成人午夜高清在线视频| 女同久久另类99精品国产91| 欧美成狂野欧美在线观看| ponron亚洲| 欧美色欧美亚洲另类二区| 此物有八面人人有两片| 国产精品野战在线观看| 一个人免费在线观看的高清视频| 一个人看视频在线观看www免费| 九九热线精品视视频播放| 久久久久免费精品人妻一区二区| 欧美激情在线99| 在线a可以看的网站| 日本一二三区视频观看| 亚洲最大成人手机在线| 又紧又爽又黄一区二区| 日韩亚洲欧美综合| 亚洲成人久久性| 热99re8久久精品国产| 村上凉子中文字幕在线| 一卡2卡三卡四卡精品乱码亚洲| 男女做爰动态图高潮gif福利片| 亚洲天堂国产精品一区在线| 亚洲精品粉嫩美女一区| 欧美+日韩+精品| 免费搜索国产男女视频| 熟女电影av网| 国产精品美女特级片免费视频播放器| 日韩欧美精品v在线| 免费黄网站久久成人精品 | 国产在线男女| 男女之事视频高清在线观看| .国产精品久久| 久久午夜亚洲精品久久| 99国产极品粉嫩在线观看| 中出人妻视频一区二区| 国产私拍福利视频在线观看| av专区在线播放| 欧美一区二区亚洲| 亚洲av二区三区四区| 亚洲最大成人手机在线| 2021天堂中文幕一二区在线观| 中文字幕免费在线视频6| 色吧在线观看| 成人精品一区二区免费| 国产黄色小视频在线观看| 免费无遮挡裸体视频| 桃红色精品国产亚洲av| 此物有八面人人有两片| 亚洲不卡免费看| 国产成年人精品一区二区| 午夜免费男女啪啪视频观看 | 国产精品日韩av在线免费观看| 亚洲无线观看免费| 久久午夜福利片| 1000部很黄的大片| 亚洲第一欧美日韩一区二区三区| 色吧在线观看| 韩国av一区二区三区四区| 久久久久久久精品吃奶| 两个人的视频大全免费| 国产成人欧美在线观看| 美女黄网站色视频| 在线观看舔阴道视频| 国产精品久久久久久人妻精品电影| 一区二区三区激情视频| 熟女人妻精品中文字幕| 色噜噜av男人的天堂激情| 亚洲人成网站高清观看| 深爱激情五月婷婷| 三级男女做爰猛烈吃奶摸视频| 午夜精品久久久久久毛片777| 国产男靠女视频免费网站| 亚洲不卡免费看| 国产精品三级大全| 欧美精品啪啪一区二区三区| 国产精华一区二区三区| 人人妻人人澡欧美一区二区| 99久久成人亚洲精品观看| 久久久久久国产a免费观看| 国产探花极品一区二区| 亚洲欧美清纯卡通| 免费看a级黄色片| 在线播放国产精品三级| 琪琪午夜伦伦电影理论片6080| 99国产精品一区二区三区| 桃红色精品国产亚洲av| 午夜福利18| 国内久久婷婷六月综合欲色啪| 国产三级黄色录像| 成人国产综合亚洲| av女优亚洲男人天堂| 日韩欧美精品v在线| 男女那种视频在线观看| 俄罗斯特黄特色一大片| 亚洲中文字幕日韩| 色视频www国产| 他把我摸到了高潮在线观看| 在线播放无遮挡| 久久天躁狠狠躁夜夜2o2o| 国产爱豆传媒在线观看| 免费黄网站久久成人精品 | 成人高潮视频无遮挡免费网站| 亚洲五月婷婷丁香| 亚洲美女黄片视频| 九色国产91popny在线| 俄罗斯特黄特色一大片| 亚洲第一区二区三区不卡| 亚洲成a人片在线一区二区| 国产免费av片在线观看野外av| 少妇的逼水好多| 老鸭窝网址在线观看| 午夜福利高清视频| 亚洲男人的天堂狠狠| 国产三级黄色录像| 在线观看66精品国产| 一级黄片播放器| 免费av毛片视频| 91在线观看av| a在线观看视频网站| 2021天堂中文幕一二区在线观| 国产色爽女视频免费观看| 午夜亚洲福利在线播放| 不卡一级毛片| 成熟少妇高潮喷水视频| 国产一区二区激情短视频| 成人国产综合亚洲| 美女 人体艺术 gogo| 国产蜜桃级精品一区二区三区| 国产精品不卡视频一区二区 | 日韩欧美国产一区二区入口| 国产精品永久免费网站| 最近视频中文字幕2019在线8| 日本成人三级电影网站| 97超级碰碰碰精品色视频在线观看| 免费电影在线观看免费观看| 欧美日韩国产亚洲二区| 欧美成狂野欧美在线观看| 少妇被粗大猛烈的视频| 国产av麻豆久久久久久久| 嫩草影院入口| 国产av在哪里看| 国产在线精品亚洲第一网站| 男女之事视频高清在线观看| 老熟妇仑乱视频hdxx| 亚洲国产精品久久男人天堂| 淫秽高清视频在线观看| 国产精品久久久久久人妻精品电影| 97碰自拍视频| 国产高清三级在线| 51午夜福利影视在线观看| 12—13女人毛片做爰片一| 亚洲美女搞黄在线观看 | 十八禁网站免费在线| 少妇熟女aⅴ在线视频| 欧美日韩福利视频一区二区| 黄色女人牲交| 成人永久免费在线观看视频| 久9热在线精品视频| av欧美777| 国产亚洲精品综合一区在线观看| 18禁裸乳无遮挡免费网站照片| 亚洲国产精品sss在线观看| 国产精品野战在线观看| 18禁裸乳无遮挡免费网站照片| 美女大奶头视频| 日日摸夜夜添夜夜添小说| 97热精品久久久久久| 丁香欧美五月| 午夜视频国产福利| 青草久久国产| 中文字幕人成人乱码亚洲影| 午夜视频国产福利| 毛片女人毛片| 久久精品国产亚洲av香蕉五月|