• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Post-welding behaviour of S690Q high strength steel butt joints

    2021-03-07 12:14:38ng

    , , , , ng

    1.Singapore Institute of Technology, Singapore138683,Singapore; 2.Nanyang Technological University, Singapore 639798,Singapore; 3.University of New South Wales, Canberra, Australia)

    Abstract: In this study, we investigated the post-welding behaviour of S690Q high strength steel butt joints experimentally. Three S690Q high strength steel butt joints were welded with 8 mm thickness plate by shield metal arc welding with different welding heat inputs. Microstructure observation and micro-hardness test of heat-affected zone were employed to reveal the welding influence on the joints at the micro level, and tensile test of S690Q high strength steel butt joints showed the welding impact at the macro level. The microstructure test indicated that the main microstructure of the S690Q high strength steel was tempered martensite and was transformed to granular bainite in the coarse-grained heat-affected zone and to ferrite and cementite in the fine-grained heat-affected zone after welding of the joints. In the tempering zone, some of the tempered martensite decomposed to ferrite. Based on the hardness test results, it can be observed there is a soft layer in the heat-affected zone with lower hardness compared with the base material. In addition, the width of the heat-affected zone increased in the joint welded with higher heat input. The subsequent tensile test showed that the formation of a soft layer directly impairs the tensile behaviour of S690Q high strength steel butt joints, and the strength deterioration becomes more serious with the increase of the welding heat input.

    Keywords:high strength steel; butt joint; microstructure; hardness; tensile behavior

    1 Introduction

    High strength to weight ratio in steel structures is an important advantage since it can result in better architectural expression and economic benefits such as less labor and transportation costs[1]. With the development of metallurgical technology, the strength to weight ratio of steel is further improved by using high strength steel with yield strength higher than 460 MPa. Among different high strength steel available in the market, reheated, quenched and tempered high strength steel is preferred since it has prominent weldability due to similar chemical composition with normal steel. Generally, reheated, quenched and tempered high strength steel is available in the form of plate since it is more conducive to achieving uniform material properties under the quenching and tempering process. That means welding, which is usually accompanied by dramatic temperature change around the joint, is inevitable for the built-up reheated, quenched and tempered high strength steel structural member. According to related investigations, reheated, quenched and tempered high strength steel is quite susceptible to high temperatures[2-3], and its strength could be significantly reduced after cooling[4-5]. Previous study also revealed that welded high strength steel butt joints lost 3% to 8% tensile strength in the condition of the area with reduced strength (soft layer) ranging from 0.33 to 0.6 times of specimen thickness[6].

    The formation of a soft layer in welded high strength steel butt joints is mainly caused by microstructure transformation in the heat-affected zone. The heat-affected zone of the welded butt joints can be roughly divided into three sub-heat-affected zones, including the coarse-grained heat-affected zone, the fine-grained heat-affected zone and the tempering zone[7]. In the coarse-grained heat-affected zone, the bainitic microstructure and martensite-austenite (M-A) constituents constitute the main microstructure after welding[8]. These microstructures have slightly lower hardness compared with the base material (tempered martensite) but are sensitive to cleavage cracking, especially when some austenite is retained after the bainite transformation. The main microstructures of the fine-grained heat-affected zone are generally composed of ferrite, pearlite or cementite[9]. In the tempering zone, parts of the tempered martensite decompose to ferrite after the welding process. Since ferrite, pearlite or cementite commonly have lower hardness compared with tempered martensite or bainite, the fine-grained heat-affected zone and the tempering zone are usually regarded as soft layer[10]. Overall, the microstructure transformation caused by welding leads to not only the reduction of tensile strength but also significant nonhomogeneity of the material within the heat-affected zone[11].

    In this study,the post-welding behaviour of S690Q high strength steel butt joints was investigated experimentally. Three butt joints were welded with 8 mm thickness reheated, quenched and tempered S690Q high strength steel plate by shield metal arc welding with different welding heat inputs. The microstructure transformation and hardness distribution in the heat-affected zones of the joints were revealed by light optical microscopy and micro-hardness tests, respectively. After this, tensile tests were conducted to find out the welding influence on the strength of the S690Q high strength steel butt joints.

    2 Material property and joint fabrication

    The high strength steel used in the tests was grade S690Q with nominal yield strength 690 MPa and tensile strength between 790 MPa and 930 MPa. The plate is delivered by the reheated, quenched and tempered procedure, and its chemical composition is similar to that of mild steel. Therefore, it has favorable weldability[12-13]. The weld material LB-80L was used as filler metal, satisfying the specification of AWS A5.5 E11018-G[14]. The mechanical property and chemical composition (together with the carbon equivalent CE) of S690Q high strength steel and LB-80L are listed in Table 1 and 2, respectively. It can be seen from Table 1 that the mechanical property of the filler metal is quite similar to that of the S690Q high strength steel used.

    Table 1 Mechanical properties of S690 high strength steel and weld metal

    Table 2 Chemical composition of S690 high strength steel and weld metal %

    Three S690Q high strength steel butt joints with 8 mm thickness were welded by shield metal arc welding. Different diameter electrodes, such as 3.2 mm, 4.0 mm and 5.0 mm, were used to gain different welding heat inputs. Four type-K thermocouples with 1 000 ℃ measuring limitation were employed to monitor the temperature history of the butt joints during welding, named thermocouple- 1, 2, 3 and 4, respectively. The arrangement of the thermocouples is presented in Fig.1(a), and the corresponding positions are described in Fig.3(a). The temperature measurement device is TDS-530 datalogger, as shown in Fig.1(b). The joints were all welded with four passes marked by 1, 2, 3 and 4 in Fig 2.

    Fig.1 Test setup for the welding process of the S690Q high strength steel butt

    Fig.2 Configuration of the welding

    Fig.3 Dimension of the welded S690Q high strength steel butt joint and machined-out

    The welding parameters of each welding pass for the three joints are listed in Table 3. It should be noted that the root pass for all the joints in this study was completed using a 3.2 mm electrode with voltage 30 V and current 73 A. In fact, the average welding heat input of BJ8-5.0 was lower than BJ8-4.0. That is because the deposition rate of the 5 mm diameter electrode was too high for BJ8-5.0 to control the welding quality if using the same welding speed for BJ8-4.0. Therefore, the welding speed of BJ8-5.0 was increased, and its average welding heat input was reduced. The temperature history curves of the butt joint are described in Fig.4.

    Table 3 Welding parameters of reheated, quenched and tempered S690Q high strength steel butt joints

    Fig.4 Temperature history curves of S690Q high

    After the welding process was completed, an 8 mm×12 mm×40 mm block and two coupons were machined out. The position of the block and coupons in the butt joint is presented in Fig.3(a). The block was further cut into two halves from the center line of the weld. One was used for microstructure observation, and the other was used for the micro-hardness test. The microstructure and micro-hardness tests were employed to reveal the welding influence on the joint at the micro level. The coupons were used in the tensile test to find out the welding impact on the strength of the S690Q high strength steel butt joints at the macro level. The corresponding dimension is illustrated in Fig.3(b).

    3 Test results

    3.1 Microstructure test

    One half of the block was cast with epoxy, polished, etched with 2% nital solution and then observed under a light optical microscope to study the detailed microstructure transformation in heat-affected zone. In the welding process, the peak temperature of the coarse-grained heat-affected zone is almost up to the melting point (higher than Ac3), and the cooling rate of the coarse-grained heat-affected zone in the following cooling stage is quite fast. This welding thermal cycle directly results in the coarsening of the grain size[15]. From the perspective of microstructure, with the temperature of the coarse-grained heat-affected zone above Ac3, the growth of austenite grains is improved due to extended time at high temperature. The consecutive fast cooling leads to the generation of a coarse martensitic microstructure from the austenite[16]. The coarse-grained heat-affected zone of the high strength steel joint is generally accompanied by several detrimental characteristics (large prior austenite grain size, upper bainite, martensite-austenite (M-A) constituents, and microalloy precipitates) which may lead to lowest toughness in the heat-affected zone. Among the mentioned microstructural features, the M-A constituent (crack susceptibility) plays an important role in leading to the decrease of joint toughness[17]. The peak temperature of the fine-grained heat-affected zone also exceeds Ac3, resulting in a fully austenitized local microstructure. Nevertheless, the time above Ac3 in the fine-grained heat-affected zone is short and limits the grain growth. The microstructures mainly consist of ferrite and a little pearlite with grain size 1-3 mm. Compared with martensite in the coarse grain heat-affected zone, the ferrite and pearlite in the fine-grained heat-affected zone have lower hardness, and therefore have a softening effect on the mechanical performance of high strength steel welded joints[18].

    Fig.5 shows the microstructure of the base material, the coarse-grainedheat-affected zone, the fine-grained heat-affected zone and the tempering zone. As show in Fig.5(a), the main microstructure of the S690Q high strength steel used in the tests was tempered martensite. After welding, the tempered martensite of the base material was transformed to granular bainite in the coarse-grained heat-affected zone (Fig.5(b)). The granular bainite was composed of a bainitic ferrite matrix and the martensite-austenite (M-A) phase as the second phase. In the fine-grained heat-affected zone, the microstructure was transformed to ferrite and cementite (Fig.5(c)). Compared with ferrite and cementite, granular bainite is generally harder, but is lower in toughness. In the tempering zone of the heat-affected zone, some of the tempered martensite decomposed to ferrite, as shown in Fig.5(d).

    Fig.5 Microstructure of S690Q high strength steel, coarse-grained heat-affected zone, fine-grained heat-affected zone and tempering

    3.2 Micro-hardness test

    Vickers hardness measurement was carried out on a micro-hardness tester according to ISO 6507-1[19]using 500 g force. Four lines of indentations were made at different thickness position of the butt joints, and the indentations were located through weld, coarse-grained heat-affected zone, fine-grained heat-affected zone, tempering zone and base material sequentially for each line, as presented in Fig.6. The obtained micro-hardness values of the butt joints are shown in Fig.7. The black line shows the physical boundary of the weld bevel which could be confidently taken as the boundary between the weld materials and the heat-affected zone.

    Fig.6 Indentation distribution on S690Q high

    As a result of the severe temperature changes in the heat-affected zone during the welding process, the microstructures with lower hardness formed in the fine-grained heat-affected zone and the tempering zone lead to the formation of a soft layer. In Fig.7, the soft layer is defined as the area between the two red dash lines, having relatively lower hardness values compared with the base material (S690Q high strength steel) with the hardness ranging from 270 Hv0.5 to 280 Hv0.5. The width of the soft layer was 6 mm, 8.875 mm, and 7.125 mm for BJ8-3.2, BJ8-4.0 and BJ8-5.0, respectively, which means the relative thickness of the soft layer (the ratio of the width of the soft layer over the plate thickness) was 0.75, 1.11, and 0.89, respectively. Considering the average welding heat input for BJ8-3.2, BJ8-4.0 and BJ8-5.0 was 1.25 kJ/mm, 1.58 kJ/mm and 1.49 kJ/mm (listed in Table 3), respectively, it can be concluded that the soft layer becomes wider for the welded S690Q high strength steel butt joints with the same thickness when higher welding heat input is adopted. The same conclusion is also suggested by Hochhauser and Rauch[6].

    Fig.7 Micro-hardness distribution of S690Q high

    3.3 Tensile test

    Tensile tests of the S690Q high strength steel butt joints were conducted on the 5900 series universal testing instruments according to EN 10002-1[20]. An extensometer with 50 mm gauge length was used to capture the deformation of the coupon. The loading rate was set as 0.5 mm/min until the joint fractured. From Fig.8, it can be seen that the tested butt joints all fractured within the heat-affected zone. The corresponding stress-strain curves are presented in Fig.9.

    Fig.8 Failure modes of S690Q high strength steel butt

    Fig.9 Stress-strain curves of S690Q high

    Both the strength and the ductility of the S690Q high strength steel butt joint deteriorated after welding, and the deterioration of mechanical performance became more serious with the increase of welding heat input. The characteristic strength of the three joints are listed in Table 4, as well as the fracture elongation. The reduction of yield strength ranged from 19% to 27% and the deterioration of ultimate tensile strength changed from 13% to 18%, when the welding heat input was increased from 1.25 kJ/mm to 1.58 kJ/mm, leading to relative thickness of the soft layer raised from 0.75 to 1.11. Compared with the conclusion obtained by Hochhauser and Rauch[6], the variation tendency of tensile strength with different relative thicknesses of soft layer was the same, although the strength deterioration was more serious due to the wider soft layer based on the results in this study.

    Table 4 Mechanical property of S690Q high strength steel butt joints

    The mechanical behaviour deterioration of the S690 high strength steel butt joints tested after welding was mainly caused by the soft layer, which was generated during welding, due to microstructure transformation. Additionally, the residual stress caused by the welding process led to the stiffness reduction of the S690Q high strength steel butt joint, which explains why the deterioration of yield strength was more serious compared with the ultimate tensile strength. The decreased elongation can be explained by two reasons. The first is the high concentration of plastic strain caused by the welding process, and the second is that the deformation of S690Q high strength steel butt joints mainly occurs within the heat-affected zone due to the existence of the soft layer instead of uniform deformation in the whole gauge length.

    4 Conclusion

    This study reveals the post-welding behaviour of S690Q high strength steel butt joints, taking the welding heat input as the principle factor. By microstructure observation, the microstructure transformation was confirmed in the heat-affected zone during the welding process, such as the granular bainite formed in the coarse-grained heat-affected zone, the ferrite and cementite generated in the fine-grained heat-affected zone, and the ferrite occurring in the tempering zone. The micro-hardness test revealed that a “soft layer” was generated in the heat-affected zone and the relative thickness of the soft layer was increased from 0.75 to 1.11 with the welding heat input raised from 1.25 kJ/mm to 1.58 kJ/mm for the 8 mm thickness joints. In the followed tensile tests, the softening effect of the welding process on S690Q high strength steel butt joints was indicated in view of the fact that the reduction of yield strength ranged from 19% to 27% and the deterioration of ultimate tensile strength changed from 13% to 18%, when the welding heat input was increased from 1.25 kJ/mm to 1.58 kJ/mm for the fabrication of butt joints with 8 mm thickness with the relative thickness of the soft layer ranging from 0.75 to 1.11. The reason why the deterioration of the yield strength is more serious compared with the ultimate tensile strength is that the the residual stress caused by the welding process leads to reduction in the stiffness of the S690Q high strength steel butt joint.

    Acknowledgements

    The financial support from the Regency Steel Asia Endowment Fund at Nanyang Technological University to the authors is gratefully acknowledged.

    国产又色又爽无遮挡免费看| 亚洲第一电影网av| av视频在线观看入口| 国产激情欧美一区二区| 91麻豆av在线| 欧美黄色淫秽网站| 亚洲成国产人片在线观看| 色综合欧美亚洲国产小说| 精品欧美一区二区三区在线| 亚洲专区字幕在线| www.自偷自拍.com| 午夜影院日韩av| 亚洲 欧美 日韩 在线 免费| 一个人观看的视频www高清免费观看 | 日韩中文字幕欧美一区二区| 亚洲精品久久成人aⅴ小说| 欧美日韩亚洲综合一区二区三区_| 视频在线观看一区二区三区| 在线播放国产精品三级| 在线观看免费视频日本深夜| 久久精品国产清高在天天线| 最近最新免费中文字幕在线| 国产片内射在线| 亚洲国产欧美网| 欧美一区二区精品小视频在线| 欧美黄色片欧美黄色片| 久久九九热精品免费| 国产精品秋霞免费鲁丝片| x7x7x7水蜜桃| 两人在一起打扑克的视频| 欧美绝顶高潮抽搐喷水| 精品欧美一区二区三区在线| 1024视频免费在线观看| 国产精品香港三级国产av潘金莲| 日韩成人在线观看一区二区三区| 老熟妇仑乱视频hdxx| 大型黄色视频在线免费观看| 无遮挡黄片免费观看| 久久精品aⅴ一区二区三区四区| 99精品欧美一区二区三区四区| 国产精品爽爽va在线观看网站 | 国产精品 国内视频| 亚洲第一欧美日韩一区二区三区| 色老头精品视频在线观看| 无遮挡黄片免费观看| 99国产综合亚洲精品| 午夜老司机福利片| 好看av亚洲va欧美ⅴa在| 一进一出抽搐gif免费好疼| 日本精品一区二区三区蜜桃| 在线观看日韩欧美| 国产亚洲精品综合一区在线观看 | 女同久久另类99精品国产91| 国产精品二区激情视频| 在线观看日韩欧美| 欧美乱码精品一区二区三区| 啦啦啦免费观看视频1| 免费观看人在逋| 女人精品久久久久毛片| 欧美激情久久久久久爽电影 | 精品久久久久久久久久免费视频| 免费在线观看影片大全网站| 人人妻人人澡欧美一区二区 | 桃红色精品国产亚洲av| 人人妻人人澡人人看| 精品国产乱码久久久久久男人| 午夜精品久久久久久毛片777| 久久伊人香网站| 看免费av毛片| 天天一区二区日本电影三级 | 午夜老司机福利片| 人妻久久中文字幕网| 91老司机精品| 欧美性长视频在线观看| 中文亚洲av片在线观看爽| 99国产极品粉嫩在线观看| 在线观看一区二区三区| 亚洲精品国产精品久久久不卡| 亚洲一码二码三码区别大吗| 久久香蕉激情| 亚洲av电影不卡..在线观看| 免费在线观看日本一区| 欧美国产精品va在线观看不卡| 国产99白浆流出| 亚洲国产毛片av蜜桃av| 国产精品二区激情视频| 两个人视频免费观看高清| 一级作爱视频免费观看| 日本在线视频免费播放| 婷婷精品国产亚洲av在线| 亚洲精品一区av在线观看| 亚洲视频免费观看视频| 天天添夜夜摸| 色精品久久人妻99蜜桃| 免费不卡黄色视频| 最近最新中文字幕大全电影3 | 精品第一国产精品| 国产精品亚洲美女久久久| 久久久久久免费高清国产稀缺| 亚洲国产毛片av蜜桃av| 国产一区二区三区综合在线观看| 两个人视频免费观看高清| 亚洲人成伊人成综合网2020| 九色国产91popny在线| 欧美乱码精品一区二区三区| 亚洲精品国产区一区二| 久久精品aⅴ一区二区三区四区| 亚洲av成人av| 一二三四社区在线视频社区8| 两个人免费观看高清视频| 韩国精品一区二区三区| 中文亚洲av片在线观看爽| 国产精品乱码一区二三区的特点 | 日韩免费av在线播放| 成人国产综合亚洲| 成人18禁在线播放| 99久久精品国产亚洲精品| 夜夜夜夜夜久久久久| 久久香蕉激情| aaaaa片日本免费| 夜夜夜夜夜久久久久| 国产精品秋霞免费鲁丝片| 久久天躁狠狠躁夜夜2o2o| 99精品久久久久人妻精品| 亚洲国产中文字幕在线视频| 黑人操中国人逼视频| 亚洲成人免费电影在线观看| 在线永久观看黄色视频| 国产精品爽爽va在线观看网站 | 高清在线国产一区| 韩国精品一区二区三区| 色精品久久人妻99蜜桃| 看黄色毛片网站| 国产欧美日韩一区二区三区在线| 一区二区日韩欧美中文字幕| 欧美激情 高清一区二区三区| 成人免费观看视频高清| av超薄肉色丝袜交足视频| 久久久久久亚洲精品国产蜜桃av| 人妻丰满熟妇av一区二区三区| 精品福利观看| 久久久国产欧美日韩av| or卡值多少钱| 日韩欧美在线二视频| 黑人巨大精品欧美一区二区mp4| 99精品欧美一区二区三区四区| 国产精品美女特级片免费视频播放器 | 两个人免费观看高清视频| 两性夫妻黄色片| 午夜日韩欧美国产| 免费av毛片视频| 99在线视频只有这里精品首页| netflix在线观看网站| 午夜影院日韩av| a级毛片在线看网站| 亚洲在线自拍视频| 久久国产精品男人的天堂亚洲| 最近最新免费中文字幕在线| 久久精品国产综合久久久| av在线播放免费不卡| 久久久久九九精品影院| 国产成+人综合+亚洲专区| 精品人妻在线不人妻| 两性夫妻黄色片| 亚洲午夜理论影院| 久久中文看片网| x7x7x7水蜜桃| 在线观看www视频免费| 色综合站精品国产| 国产av一区在线观看免费| 成人av一区二区三区在线看| av超薄肉色丝袜交足视频| svipshipincom国产片| 亚洲成a人片在线一区二区| 两个人视频免费观看高清| 午夜福利视频1000在线观看 | 国产高清视频在线播放一区| 99热只有精品国产| 亚洲五月天丁香| 欧美日韩亚洲国产一区二区在线观看| 一级黄色大片毛片| 免费看美女性在线毛片视频| 脱女人内裤的视频| av欧美777| 后天国语完整版免费观看| 亚洲一区二区三区不卡视频| 91精品三级在线观看| 亚洲免费av在线视频| 国产精品98久久久久久宅男小说| av在线天堂中文字幕| 亚洲精品国产色婷婷电影| 日韩免费av在线播放| 久久久久久久精品吃奶| 在线国产一区二区在线| 国产成年人精品一区二区| 亚洲成a人片在线一区二区| 在线观看66精品国产| 成人免费观看视频高清| 久久久久精品国产欧美久久久| www.自偷自拍.com| 免费看十八禁软件| 国产免费男女视频| 中文字幕人妻丝袜一区二区| 亚洲精品国产一区二区精华液| 一区二区三区高清视频在线| 色精品久久人妻99蜜桃| 亚洲自偷自拍图片 自拍| 99热只有精品国产| 法律面前人人平等表现在哪些方面| 999久久久国产精品视频| 大型av网站在线播放| 窝窝影院91人妻| 欧美在线黄色| 亚洲国产精品sss在线观看| 一级,二级,三级黄色视频| 午夜日韩欧美国产| 国产欧美日韩精品亚洲av| 成年女人毛片免费观看观看9| 亚洲 欧美 日韩 在线 免费| 国产精品 国内视频| 看黄色毛片网站| 色综合亚洲欧美另类图片| 日韩一卡2卡3卡4卡2021年| 精品福利观看| 黄频高清免费视频| 一区二区三区国产精品乱码| 88av欧美| 成人18禁在线播放| 美女午夜性视频免费| 黄片大片在线免费观看| 91大片在线观看| 免费在线观看视频国产中文字幕亚洲| 色哟哟哟哟哟哟| 亚洲av成人av| 亚洲一卡2卡3卡4卡5卡精品中文| 9色porny在线观看| 日韩中文字幕欧美一区二区| 在线免费观看的www视频| 老鸭窝网址在线观看| 大码成人一级视频| 老司机深夜福利视频在线观看| 日韩成人在线观看一区二区三区| 久久精品国产亚洲av高清一级| 一卡2卡三卡四卡精品乱码亚洲| 成人国产综合亚洲| 国产欧美日韩一区二区三| 亚洲五月婷婷丁香| 精品福利观看| а√天堂www在线а√下载| 成人18禁高潮啪啪吃奶动态图| 亚洲一区二区三区色噜噜| 欧美一级a爱片免费观看看 | 十八禁网站免费在线| 欧美色视频一区免费| 久久午夜综合久久蜜桃| 欧美日韩黄片免| 亚洲欧美一区二区三区黑人| 波多野结衣巨乳人妻| 亚洲第一青青草原| 老司机福利观看| 亚洲av成人不卡在线观看播放网| 后天国语完整版免费观看| 成年版毛片免费区| 51午夜福利影视在线观看| 可以在线观看毛片的网站| av视频免费观看在线观看| 免费不卡黄色视频| 此物有八面人人有两片| 欧美人与性动交α欧美精品济南到| 午夜激情av网站| 天天添夜夜摸| 色播在线永久视频| 成人免费观看视频高清| 精品一区二区三区av网在线观看| 欧美老熟妇乱子伦牲交| 午夜成年电影在线免费观看| www.自偷自拍.com| 精品免费久久久久久久清纯| 在线观看午夜福利视频| 色综合站精品国产| 99香蕉大伊视频| 中文字幕av电影在线播放| 欧美av亚洲av综合av国产av| 久久这里只有精品19| 999精品在线视频| 久久精品91无色码中文字幕| 亚洲色图av天堂| 香蕉丝袜av| 中文字幕av电影在线播放| 久久中文看片网| 精品久久久久久成人av| 99re在线观看精品视频| 久久久久国产一级毛片高清牌| 日韩精品青青久久久久久| a在线观看视频网站| 欧美激情久久久久久爽电影 | 精品卡一卡二卡四卡免费| 长腿黑丝高跟| 国产精品一区二区免费欧美| 午夜福利,免费看| 久久草成人影院| 亚洲欧美精品综合一区二区三区| 老汉色av国产亚洲站长工具| 国产精品久久久久久精品电影 | 一个人观看的视频www高清免费观看 | 亚洲精品国产一区二区精华液| 久久久久久人人人人人| 日本a在线网址| 淫妇啪啪啪对白视频| 国产又色又爽无遮挡免费看| 后天国语完整版免费观看| 天天一区二区日本电影三级 | 欧洲精品卡2卡3卡4卡5卡区| 午夜福利高清视频| 又大又爽又粗| 99久久99久久久精品蜜桃| 一a级毛片在线观看| 国产成人影院久久av| 午夜久久久久精精品| 男人舔女人的私密视频| 国产精品 国内视频| 91精品国产国语对白视频| 99re在线观看精品视频| 欧美乱妇无乱码| 女人爽到高潮嗷嗷叫在线视频| 亚洲精品美女久久av网站| 两个人看的免费小视频| 久久婷婷人人爽人人干人人爱 | 色综合亚洲欧美另类图片| 成熟少妇高潮喷水视频| 精品国产一区二区三区四区第35| 欧美成人免费av一区二区三区| 欧美日本亚洲视频在线播放| 十分钟在线观看高清视频www| 大型黄色视频在线免费观看| 国产成人一区二区三区免费视频网站| 久久欧美精品欧美久久欧美| 免费在线观看亚洲国产| 欧美+亚洲+日韩+国产| 中文字幕人妻熟女乱码| 午夜精品国产一区二区电影| 在线观看免费午夜福利视频| 嫩草影视91久久| 欧美日韩一级在线毛片| 天天躁夜夜躁狠狠躁躁| 国产麻豆69| 欧美+亚洲+日韩+国产| 久99久视频精品免费| 亚洲成人久久性| 如日韩欧美国产精品一区二区三区| 亚洲国产高清在线一区二区三 | 午夜老司机福利片| av中文乱码字幕在线| 三级毛片av免费| 日韩免费av在线播放| 欧美日韩一级在线毛片| 亚洲av成人不卡在线观看播放网| 99久久精品国产亚洲精品| 国产精品久久久久久亚洲av鲁大| 极品人妻少妇av视频| 人人妻,人人澡人人爽秒播| 国产欧美日韩综合在线一区二区| 久久欧美精品欧美久久欧美| 国产亚洲欧美98| 村上凉子中文字幕在线| 少妇的丰满在线观看| 在线天堂中文资源库| 久久人妻av系列| 欧美午夜高清在线| 两个人看的免费小视频| 亚洲熟妇熟女久久| 91精品国产国语对白视频| 琪琪午夜伦伦电影理论片6080| 久久 成人 亚洲| 19禁男女啪啪无遮挡网站| 一级毛片女人18水好多| 久久久久久大精品| 好看av亚洲va欧美ⅴa在| 欧美日韩亚洲综合一区二区三区_| 国产亚洲精品一区二区www| 免费看美女性在线毛片视频| 亚洲国产精品合色在线| 一级片免费观看大全| 老司机在亚洲福利影院| 亚洲精华国产精华精| 精品不卡国产一区二区三区| 91国产中文字幕| 久久精品91蜜桃| tocl精华| 成人av一区二区三区在线看| 国产麻豆69| 最好的美女福利视频网| 精品欧美一区二区三区在线| 国产av一区二区精品久久| 日本在线视频免费播放| 国产成年人精品一区二区| 高潮久久久久久久久久久不卡| 国产一区二区三区综合在线观看| 日日爽夜夜爽网站| 亚洲狠狠婷婷综合久久图片| 欧美 亚洲 国产 日韩一| 黄色视频,在线免费观看| 亚洲自偷自拍图片 自拍| 两个人视频免费观看高清| 成年版毛片免费区| 男人的好看免费观看在线视频 | 久久国产精品影院| 欧美乱妇无乱码| 久久久久久免费高清国产稀缺| 久久久国产成人免费| 久久久久久人人人人人| 国产精华一区二区三区| 午夜激情av网站| 欧美成人一区二区免费高清观看 | 中国美女看黄片| 国产在线精品亚洲第一网站| 在线视频色国产色| 99在线视频只有这里精品首页| 欧美精品亚洲一区二区| 叶爱在线成人免费视频播放| 久久热在线av| 精品国产一区二区三区四区第35| 三级毛片av免费| 国产99白浆流出| 色精品久久人妻99蜜桃| 国产成+人综合+亚洲专区| 搡老妇女老女人老熟妇| 亚洲欧美精品综合一区二区三区| 如日韩欧美国产精品一区二区三区| 国产精品综合久久久久久久免费 | 9191精品国产免费久久| 最新在线观看一区二区三区| 在线观看66精品国产| 国产伦人伦偷精品视频| 可以在线观看毛片的网站| 一区福利在线观看| 女人精品久久久久毛片| 午夜视频精品福利| 又大又爽又粗| 手机成人av网站| 亚洲九九香蕉| 黑人操中国人逼视频| 欧美日韩中文字幕国产精品一区二区三区 | www国产在线视频色| 97人妻精品一区二区三区麻豆 | 国产精品野战在线观看| 精品国产乱码久久久久久男人| 好看av亚洲va欧美ⅴa在| 大型av网站在线播放| 亚洲人成网站在线播放欧美日韩| 久久香蕉激情| 欧美av亚洲av综合av国产av| 中文字幕最新亚洲高清| 美女高潮到喷水免费观看| 香蕉久久夜色| 夜夜爽天天搞| 欧美日韩黄片免| 久久这里只有精品19| 国产又爽黄色视频| 欧美大码av| 琪琪午夜伦伦电影理论片6080| 久久精品亚洲精品国产色婷小说| 麻豆av在线久日| 欧美黑人欧美精品刺激| 真人做人爱边吃奶动态| 亚洲av熟女| 曰老女人黄片| 亚洲成av人片免费观看| 午夜免费成人在线视频| 欧美中文综合在线视频| 亚洲熟妇中文字幕五十中出| 国产成+人综合+亚洲专区| 亚洲精华国产精华精| 亚洲成人久久性| 亚洲一区高清亚洲精品| 丰满的人妻完整版| 麻豆一二三区av精品| 制服丝袜大香蕉在线| 国产精品免费视频内射| 一进一出抽搐动态| 日韩 欧美 亚洲 中文字幕| 9色porny在线观看| 亚洲性夜色夜夜综合| 日韩精品中文字幕看吧| 男人操女人黄网站| 午夜福利18| 国产高清videossex| 国产一区二区在线av高清观看| 又黄又粗又硬又大视频| 久久久久九九精品影院| 乱人伦中国视频| www.精华液| 欧美日本中文国产一区发布| 中文字幕精品免费在线观看视频| 桃红色精品国产亚洲av| 女人高潮潮喷娇喘18禁视频| 国产人伦9x9x在线观看| 午夜福利免费观看在线| 国产精品99久久99久久久不卡| 一级作爱视频免费观看| 欧美在线黄色| 看免费av毛片| 满18在线观看网站| 免费在线观看影片大全网站| 大码成人一级视频| www.999成人在线观看| 久久精品国产综合久久久| 亚洲黑人精品在线| 午夜福利高清视频| 国产精品久久电影中文字幕| 国产一区二区在线av高清观看| 色婷婷久久久亚洲欧美| 久久九九热精品免费| 男女午夜视频在线观看| 制服人妻中文乱码| 国产91精品成人一区二区三区| 看黄色毛片网站| 老鸭窝网址在线观看| 久久精品91蜜桃| 亚洲免费av在线视频| 久久中文看片网| 韩国av一区二区三区四区| 久久精品成人免费网站| 国产精品综合久久久久久久免费 | 国产男靠女视频免费网站| 色尼玛亚洲综合影院| 国产精品日韩av在线免费观看 | 一级作爱视频免费观看| 在线观看一区二区三区| 国产成人免费无遮挡视频| 亚洲av熟女| 午夜视频精品福利| 午夜久久久在线观看| 久久久久久国产a免费观看| 亚洲国产精品合色在线| 精品熟女少妇八av免费久了| 精品一品国产午夜福利视频| 麻豆一二三区av精品| av超薄肉色丝袜交足视频| www.自偷自拍.com| 正在播放国产对白刺激| 俄罗斯特黄特色一大片| 精品国产亚洲在线| 欧美黄色淫秽网站| www.999成人在线观看| 757午夜福利合集在线观看| 后天国语完整版免费观看| 欧美在线黄色| 免费一级毛片在线播放高清视频 | 久久 成人 亚洲| 久久亚洲真实| 男人舔女人的私密视频| 亚洲第一电影网av| 亚洲人成77777在线视频| 久久香蕉精品热| 欧美黄色淫秽网站| www.999成人在线观看| 欧美日韩瑟瑟在线播放| 久99久视频精品免费| 久久精品aⅴ一区二区三区四区| 亚洲中文日韩欧美视频| 高清毛片免费观看视频网站| 亚洲欧美日韩无卡精品| 免费在线观看日本一区| 老鸭窝网址在线观看| 99国产极品粉嫩在线观看| 国产精品永久免费网站| 亚洲九九香蕉| 麻豆久久精品国产亚洲av| 熟女少妇亚洲综合色aaa.| 国产精品九九99| 少妇 在线观看| 精品一区二区三区四区五区乱码| 亚洲第一青青草原| 亚洲va日本ⅴa欧美va伊人久久| 国产av又大| 精品一品国产午夜福利视频| 色播在线永久视频| 在线观看免费日韩欧美大片| 久久国产精品男人的天堂亚洲| 国产1区2区3区精品| 一边摸一边抽搐一进一小说| 日韩成人在线观看一区二区三区| 国产99久久九九免费精品| 亚洲国产欧美一区二区综合| 欧美一区二区精品小视频在线| 日本在线视频免费播放| 亚洲九九香蕉| 99久久久亚洲精品蜜臀av| 午夜成年电影在线免费观看| 亚洲九九香蕉| 女人被躁到高潮嗷嗷叫费观| √禁漫天堂资源中文www| 国产精品精品国产色婷婷| 身体一侧抽搐| 欧美中文综合在线视频| 久久中文字幕人妻熟女| 国产一区二区三区视频了| 亚洲av电影不卡..在线观看| or卡值多少钱| 身体一侧抽搐| 日本vs欧美在线观看视频| 亚洲精品久久成人aⅴ小说| 午夜免费鲁丝| 国产男靠女视频免费网站| 香蕉丝袜av| 久久精品亚洲精品国产色婷小说| 久久久久久久久久久久大奶| 久久香蕉精品热| 国产精品美女特级片免费视频播放器 | 不卡av一区二区三区| www.www免费av| 91字幕亚洲| 午夜福利成人在线免费观看| 国产精品,欧美在线|