駱勇鵬 劉景良 韓建平
摘要: 參數不確定性量化及傳遞分析常需假定參數的總體分布,概率分布的選取對分析結果有較大影響。自助法無需進行分布假設即可對總體的分布特性進行統計推斷,可在一定程度解決以上問題,但是在小樣本情況下容易導致計算結果偏離真實分布。為此,采用信息擴散理論對自助法進行改進,結合響應面理論,提出新的參數不確定性量化及傳遞分析方法。該方法首先對各個Bootstrap子樣本的概率密度函數進行信息擴散估計,采用接受-拒絕法生成大量改進Bootstrap子樣本,計算不確定性參數的概率統計特征值。其次,根據不確定性量化結果,基于響應面模型,快速計算結構響應的變化區間,根據所定義的區間靈敏度指標來判斷參數不確定性對結構響應的影響程度,量化響應的不確定性。最后,通過一斜拉橋的參數不確定性量化及傳遞分析,驗證了所提方法的可行性及可靠性。
關鍵詞: 不確定性量化和傳遞; 斜拉橋; 改進自助法; 響應面模型; 有限樣本; 信息擴散
中圖分類號: TU311.4; U448.27 文獻標志碼: A 文章編號: 1004-4523(2020)04-0679-09
DOI:10.16385/j.cnki.issn.1004-4523.2020.04.005
引 言
土木工程結構的材料屬性、制造誤差、幾何特征、荷載、邊界條件及服役環境等均存在不確定性[1]。采用確定性模型與確定性方法進行分析,將無法正確有效地估計和量化結構參數不確定性對結構響應的影響,難以對結構的實際力學特性進行準確地分析與判斷。因此,如何有效地量化參數不確定性及其對結構響應的影響,對于工程結構的分析、設計和優化等具有重要指導意義[2]。
目前常用的不確定性分析方法主要有區間分析、模糊理論和概率理論,即可采用區間參數、模糊參數和隨機參數來描述參數不確定性問題。概率分析方法是三種方法中最為常用方法,而Monte Carlo法又是概率分析方法中應用較為廣泛的。該方法根據參數的概率密度函數進行隨機抽樣,通過多次有限元模型計算得到輸出響應的統計參數[3-5]。目前該方法存在的主要困難在于如何準確描述試驗參數和響應特征的概率統計分布規律。而不確定性源的描述方式直接影響不確定性分析結果的準確性與真實性[6],概率模型參數的小偏差也可能引起結構分析結果出現較大誤差[7]。當試驗樣本個數較多時,可用K-S檢驗等方法來估計不確定性參數的概率分布[8]。但是,實際工程中往往難以提供足夠的實測數據,只能基于某種假設進行。當假設的概率分布與實際分布不符時,將導致較大誤差。也有學者提出區間分析可用于參數概率分布未知的情況,但需要指出的是區間分析無法提供輸入引起輸出的詳細信息和概率特性[9],得出的不確定分析結果過于籠統,不能夠有效地指導工程實踐。因此需要一種能夠充分利用統計信息,又避免因信息過少而造成量化失真的不確定分析方法[10]。
自助法(Bootstrap抽樣)[11]運用模擬再抽樣技術代替理論分析,基于有限的試驗觀測數據模擬,再抽樣出大量符合原數據特征的模擬樣本,提供足夠的樣本進行概率統計分析,避免對概率分布函數假定的依賴,適用于小樣本不確定性參數量化。但是,研究發現自助法在每次重抽樣過程中均是從原始樣本中抽取,當原始樣本容量較小時,再抽樣得到的Bootstrap子樣本可能非常相似于原樣本,導致計算結果偏離真實分布[12]。為此,劉健等[13]通過對自助樣本生成范圍的拓展,在一定程度上克服了自助樣本生成范圍受限的不足。胡正東等[14]提出了利用驗前信息來彌補原始樣本不足的改進自助法。黃瑋等[15]研究了用指數分布函數、Boltzmann函數和三次多項式函數擬合修正樣本經驗分布函數的可行性。Yu 等[16]綜合了無模型抽樣和自助法的優勢,提出改進的Bootstrap抽樣方法。
本文引入信息擴散理論對Bootstrap抽樣進行改進,通過將單值樣本轉換成概率形式表達的模糊集值樣本,進而對非完備樣本信息進行有效處理,在一定程度上解決原始樣本限制的問題。其次在改進自助抽樣的基礎上,提出新的不確定性參數量化及傳遞分析方法,探討參數不確定性對結構動力響應的影響程度。以數值算例和斜拉橋動力響應不確定性分析為例,驗證所提方法的可行性及可靠性。
通過比較各個參數的靈敏度因子的大小判斷各個參數變異對結構動力響應不確定性的影響程度。
隨后,將靈敏度因子較高的不確定性參數的B組改進Bootstrap子樣本代入ACE響應面中,靈敏度因子較低的參數取均值,計算B組改進Bootstrap子樣本所對應的B組動力響應,進而獲得B組響應的統計特征值,如均值和標準差。用這B個統計量的分布去模擬結構響應均值和標準差的分布,從而得到響應概率統計特征值的抽樣分布及分布參數,達到估計多個參數變異對結構動力響應變化的影響以及因隨機抽樣產生的結構響應概率統計特征的估計誤差。
2 數值算例
為了考察改進Bootstrap抽樣算法的可行性及可靠性,利用一組來自已知總體的觀測樣本估計總體的分布參數。已知原始樣本X=[1.1124, 0.3679, -1.6876, -0.8223, -0.9069, -1.5200, 1.6908, -3.0461, -0.3754, -0.3704, -0.1325, 0.6321, -0.1546, 0.3655, 0.3436, 0.7355, 1.1339, -0.3106, 1.2065, -0.3256]是來自標準正態總體N(0,1)的獨立隨機觀測樣本,樣本個數n=20。
分別采用自助法、正態信息擴散及改進自助法3種方法對該組樣本的均值和標準差進行估計。表1給出了幾種方法估計的均值和標準差。從表1可知:直接根據小樣本數據得到的估計結果與實際結果誤差較大,基于自助法和信息擴散的估計結果有所改善,而本文所提的改進自助法估計的均值與標準差最接近實際值。由此可得改進的Bootstrap法在小樣本數據的情況下總體分布參數的估計精度高于自助法和信息擴散理論。
(3)抽樣隨機性對結構響應統計特征值有一定的影響,在不確定性分析中應予以量化。
參考文獻:
[1] 侯立群, 趙雪峰, 歐進萍, 等. 結構損傷診斷不確定性方法研究進展[J]. 振動與沖擊, 2014, 33(18):50-58.
Hou Liqun, Zhao Xuefeng, Ou Jinping, et al. A review of nondeterministic methods for structural damage diagnosis[J]. Journal of Vibration and Shock, 2014, 33(18):50-58.
[2] 萬華平, 任偉新, 顏王吉. 橋梁結構動力特性不確定性的全局靈敏度分析的解析方法[J]. 振動工程學報, 2016, 29(3):429-435.
Wan Huaping, Ren Weixin, Yan Wangji. Analytical global sensitivity analysis for uncertainty in structural dynamic properties of bridge[J]. Journal of Vibration Engineering, 2016, 29(3):429-435.
[3] 宗周紅, 高銘霖, 夏樟華. 基于健康監測的連續剛構橋有限元模型確認(II)—不確定性分析與模型精度評價[J]. 土木工程學報, 2011, 44(3):85-92.
Zong Zhouhong, Gao Minglin, Xia Zhanghua. Finite element model validation of the continuous rigid frame bridge based on structural health monitoring-Part II: Uncertainty analysis and evaluation of model accuracy[J]. China Civil Engineering Journal, 2011, 44(3):85-92.
[4] Sgambi L, Garavaglia E, Basso N, et al. Monte Carlo simulation for seismic analysis of a long span suspension bridge [J] Engineering Structures, 2014, 78:100-111.
[5] Wan H P, Mao Z, Todd M D, et al. Analytical uncertainty quantification for modal frequencies with structural parameter uncertainty using a Gaussian process metamodel[J]. Engineering Structures, 2014, 75: 577- 589.
[6] 王曉軍, 王 磊, 邱志平. 結構可靠性分析與優化設計的非概率集合理論[M]. 北京: 科學出版社, 2016.
Wang Xiaojun, Wang Lei, Qiu Zhiping. A Non-probabilistic Set Theory for Structural Reliability Analysis and Optimization Design [M]. Beijing: Science Press, 2016.
[7] Ben-Haim Y. A non-probabilistic concept of reliability[J]. Structural Safety, 1994, 14 (4):227-245.
[8] 陳立宏, 陳祖煜, 劉金梅. 土體抗剪強度指標的概率分布類型研究[J]. 巖土力學, 2005, 26(1): 37-40.
Chen Lihong, Chen Zuyu, Liu Jinmei. Probability distribution of soil strength[J]. Rock and Soil Mechanics, 2005, 26(1): 37-40.
[9] Qiu Z P, Chen S H, Elishakoff I. Natural frequencies of structures with uncertain but nonrandom parameters[J]. Journal of Optimization Theory and Applications, 1995, 86(3):669-683.
[10] 李大偉, 唐和生, 姚 雯, 等. 結構固有頻率不確定分析的證據理論方法[J]. 振動工程學報, 2017, 30(06) : 904-912.
Li Dawei, Tang Hesheng, Yao Wen, et al. Uncertainty quantification of structural natural frequency using evidence theory[J]. Journal of Vibration Engineering, 2017, 30(06) : 904-912.
[11] Efron B, Tibshirani R. An Introduction to Bootstrap[M]. New York: Chapman & Hall Ltd., 1993.
[12] Zhang Minghui, Liu Xintian, Wang Yansong, et al. Parameter distribution characteristics of material fatigue life using improved Bootstrap method[J]. International Journal of Damage Mechanics, 2019, 28(5): 772-793.
[13] 劉 建, 吳 翊, 譚 璐. 對Bootstrap方法的自助抽樣的改進[J]. 數學理論與應用, 2006, 26(1):69-72.
Liu Jian, Wu Yi, Tan Lu. Improvement to the resampling procedure of Bootstrap method[J]. Mathematical Theory and Applications, 2006, 26(1):69-72.
[14] 胡正東, 曹 淵, 張士峰, 等. 特小子樣試驗下導彈精度評定的Bootstrap方法[J]. 系統工程與電子技術, 2008, 30(8):1493-1497.
Hu Zhengdong, Cao Yuan, Zhang Shifeng, et al. Bootstrap method for missile precision evaluation under extreme small sample test[J]. Systems Engineering and Electronics, 2008, 30(8):1493-1497.
[15] 黃 瑋, 馮蘊雯, 呂震宙. 基于Bootstrap方法的小子樣試驗評估方法研究[J]. 機械科學與技術, 2006, 25(1):31-35.
Huang Wei, Feng Yunwen, Lü Zhenzhou. Study on small scale sample test estimation method based on Bootstrap method[J]. Mechanical Science and Technology, 2006, 25(1): 31-35.
[16] Yu Xinhui, Yang Zhaohui, Song Kunling, et al. An improved model-free sampling technique based on Bootstrap method[C]. Proceedings of the ASME 2016 International Mechanical Engineering Congress and Exposition, Phoenix, Arizona, USA, 2016.
[17] 黃崇福, 王家鼎. 模糊信息優化處理技術及其應用[M]. 北京:北京航空航天大學出版社, 1995.
Huang Chongfu, Wang Jiading. Technology of Fuzzy Information Optimization and Its Application[M]. Beijing: Beijing University of Aeronautics and Astronautics Press, 1995.
[18] Huang C F. Information diffusion technique and small sample problem[J]. Information Technology and Decision Making, 2002, 1(2):229-249.
[19] 王新洲, 游楊聲, 湯永凈. 最優信息擴散估計理論及其應用[J]. 地理空間信息, 2003, 1(1):10-17.
Wang Xinzhou, You Yangsheng, Tang Yongjing. The theory of optimal information diffusion estimation and its application[J]. Geospatial Information, 2003, 1(1): 10-17.
[20] 李曙雄, 楊振海. 舍選法的幾何解釋及其應用[J].數理統計與管理, 2002,21(7):40-43.
Li Shuxiong, Yang Zhenhai. Geometric sense of acceptance-rejection method and its applications to generate random variables[J]. Journal of Applied Statistics and Management, 2002, 21(7):40-43.
[21] Breiman L, Friedman J H. Estimating optimal transformations for multiple regression and correlation[J]. Journal of the American Statistical Association, 1985, 80:580-598.
Abstract: The population distributions of the measured data or parameters are usually assumed during uncertainty analysis in structure parameter uncertainty quantification and propagation. In fact, the different probability distributions can bring different uncertain results, which will have impact on judgments of the structure. The overall distribution characteristics can be statistically inferred without the assumption of distribution based on Bootstrap method. However, this method limits the generating range of the self-help sample, which causes the self-help sample being similar to the original sample, and the non-self-help probability distribution disagreeing with the genuine distribution. Therefore, a new method for structure parameter uncertainty quantification and propagation based on improved Bootstrap method and response surface model (RSM) is proposed. Firstly, the information diffuse theory is introduced to estimate the probability density function of the limited measured data, which can be regarded as a surrogate function of the empirical distribution function and used to establish random samples. Secondly, the random samples of uncertain parameters are put into the RSM to calculate the response. A new sensitivity index is defined to judge the influence of the uncertainty parameters on the response. Finally, the dynamic characteristic uncertainty analysis of a cable-stayed bridge is presented to investigate the feasibility and effectiveness of the proposed method.
Key words: uncertainty quantification and propagation; cable-stayed bridge; improved Bootstrap method; response surface model; limited data; information diffuse