• 
    

    
    

      99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

      Rayleigh-Type Wave in A Rotated Piezoelectric Crystal Imperfectly Bonded on a Dielectric Substrate

      2019-04-29 03:21:38GuoquanNieandMengheWang
      Computers Materials&Continua 2019年4期

      Guoquan Nie and Menghe Wang

      Abstract: Propagation characteristics of Rayleigh-type wave in a piezoelectric layered system are theoretically investigated. The piezoelectric layer is considered as a cubic crystal with finite thickness rotated about Y-axis and is imperfectly bonded onto a semi-infinite dielectric substrate. The imperfect interface between the two constituents is assumed to be mechanically compliant and dielectrically weakly conducting. The exact dispersion relations for electrically open or shorted boundary conditions are obtained.The numerical results show that the phase velocity of Rayleigh-type wave is symmetric with respect to the cut orientation of 45° and can achieve the maximum propagation speed in this orientation. The mechanical imperfection plays an important role in the dispersion relations, further the normal imperfection can produce a significant reduction of phase velocity comparing with the tangential imperfection. Comparing with the mechanical imperfection the electrical imperfection makes a relatively small reduction of phase velocity of Rayleigh-type wave. The obtained results can provide some fundamentals for understanding of piezoelectric semiconductor and for design and application of piezoelectric surface acoustic wave devices.

      Keywords: Piezoelectric cubic crystal, Rayleigh-type wave, imperfect interface, cut orientation, dispersion relation.

      1 Introduction

      Due to being able to achieve the conversion between mechanical energy and electrical energy, surface acoustic wave (SAW) devices made of piezoelectric materials are widely used as resonators, tunable filters, delay lines, sensing devices, energy harvesters and micro-electro-mechanical systems [Jakoby and Vellekoop (1997); Garner and Ohkawa(2002); Campbell and Jones (1968); Ma and Wu (2009); Ghasemi, Park and Rabczuk(2017); Ghasemi, Park and Rabczuk (2018); Hamdia, Ghasemi, Zhuang et al. (2018);Nanthakumar, Lahmer, Zhuang et al. (2016); Nanthakumar, Zhuang, Park et al. (2017);Nguyen, Nanthakumar, Zhuang et al. (2018); Thai, Rabczuk and Zhuang (2018)]. Studies of wave propagation in piezoelectric media and structures have been the subject of increasing research activity for about 50 years. At the earliest, Bluestein [Bleustein(1968)] and Gulyaev [Gulyaev (1968)] almost concurrently discovered that a shear horizontal (SH) surface wave can propagate in the hexagonal 6mm piezoelectric half-space when its surface is electrically shorted or open to the vacuum, and thus be commonly termed as Bleustein-Gulyaev (BG) wave. BG wave is a non-dispersive surface wave which exists only in piezoelectric materials. Like the Love wave its particle motion is entirely transverse and parallel to the surface, but it is confined to the surface by the piezoelectric effect rather than by a layer of a different material. These characteristics of non-dispersive and large penetration depth of BG wave greatly restricts its practical applications in acoustic and microwave devices. But if the piezoelectric half-space is replaced by a layered structure, such disadvantages of BG wave can be dramatically alleviated [Curtis and Redwood (1973); Sun and Cheng (1974)]. Many efforts therefore have been made to explore the propagation of surface waves in piezoelectric layered structures in recent decades. According to the material properties and stacking sequence of the covering layer and the substrate, piezoelectric layered systems can be classified into three forms, i.e., elastic layer/piezoelectric substrate [Curtis and Redwood (1973);Zhang and Feng (2012)], piezoelectric layer/elastic substrate [Qian, Jin and Hirose (2011);Qian and Hirose (2012); Nie, Liu and Li (2015); Singh, Parween, Kumar et al. (2018);Singh, Das, Mistri et al. (2017)], and piezoelectric layer/piezoelectric substrate [Morocha(2010); Zakharenko (2005); Singh, Kumar and Chattopadhyay (2015)]. Most of the published results on piezoelectric surface waves are for polarized ceramics and quartz for transducer and acoustic wave resonator or sensor. One of the most common types of piezoelectric crystals is the cubic crystal system which possesses the same form of macroscopic symmetry to the piezoelectric semiconductor. So, study on wave propagation in cubic crystals can offer some fundamentals for the understanding and application of piezoelectric semiconductor, such as acoustic wave amplification, stress and strain sensing, energy harvesting and conversion [Chen, Wang, Du et al. (2016)].Many researchers focused on the various wave propagating in piezoelectric cubic crystals.Tseng [Tseng (1970)] demonstrated that the elastic Rayleigh waves and the SH-PE surface wave can propagate in piezoelectric cubic crystals ofand 23 classes along the [110] direction on thesurface and their equivalent orientation, and the velocity equations for the piezoelectric surface wave and elastic surface wave were derived. Bright and Hunt [Bright and Hunt (1989)] explored an analytical solution for BG piezoelectric surface wave in cubic crystals. A general formulation of the boundary-value problem and the equation of power carried by the BG wave were presented. The existence of BG wave in six kinds of piezoelectric cubic crystals was demonstrated in their numerical examples. Rio et al. [Rio and Velasco (1985)] studied the surface wave propagating on the (100) and (110) surfaces of piezoelectric cubic crystal by using the surface Green function matching method. They found that there is no BG wave can propagate along the [100] and [110] symmetry directions on the (100) surface, while on the (110) surface BG wave can propagate along thesymmetry direction and a piezoelectric Rayleigh wave along thedirection. Zakharenko [Zakharenko(2005)] investigated the propagation of Love wave in layered half-space systems consisting of two class-23 cubic piezoelectric media, and the dispersion relations for seven partial Love-type waves were obtained numerically. Zakharenko [Zakharenko(2010)] gave a further study on interfacial SH wave propagating along the interface of two piezoelectric cubic crystals ofand 23 classes. It was found that this kind of interfacial SH wave can always propagate along the interface of two identical piezoelectric crystals with opposite polarization.

      In the studies mentioned above, the interface existing in layered system or bi-material space was considered as a perfect bonding. It is well known that the interfacial imperfection can weaken the stiffness and continuity of layered system, and further affects the wave propagation behaviors [Nie, Liu and Liu (2016)]. Considering interface imperfection, many efforts have been made on the propagation of surface waves [Liu,Wang and Wang (2010); Fan, Yang and Xu (2006); Li and Jin (2012); Singh, Chaki,Hazra et al. (2017); Singh, Kumar and Kumari (2018)] and interfacial waves [Chen, Hu and Yang (2008); Xu, Fan, Chen et al. (2006); Fan, Yang and Xu (2006); Huang and Li(2011)] in various layered structures or bi-material systems with a constituent of piezoelectric media. However, the interfacial imperfection mentioned was restricted to pure mechanical imperfection while the electrical imperfection was not considered. In fact, defects and damages to the interface are often inevitable due to electro-mechanical coupling and fatigue. Therefore, the effects of both mechanical and electrical imperfection are interesting for piezoelectric devices. Recently, Li et al. [Li, Wei and Guo(2016)] studied the propagation of Rayleigh wave in a system consisting of an elastic half-space carrying a piezoelectric gradient covering layer. Five types of gradient profiles and two types of imperfect interfaces were considered and the effects of the mechanical and dielectric interface parameters on surface wave speed are discussed. Similarly, Li et al. [Li and Lee (2010)] investigated SH wave propagating in a cylindrical piezoelectric sensor with both mechanically and electrically interfacial imperfection.

      This work is firstly motivated by the growing interest in piezoelectric semiconductors which are common cubic crystals. For the design and application of piezoelectric semiconductor devices, knowledge of the electric field accompanying mechanical deformation or acoustic waves from a piezoelectric analysis is fundamental. However,available theoretical results for cubic crystals are limited and most of them are for anti-plane problems. Rayleigh waves, however, are free plane waves propagating along the surface of a semi-infinite solid which were first theoretically predicted in 1885. While the traction forces must vanish on the boundary and the energy must decay with increased depth. Since the middle of the 20th century, Rayleigh waves were widely employed in a number of areas of science and technology, including ultrasonic nondestructive testing,structural health monitoring, electronic circuitry and other surface acoustic waves devices[Lewis (1995)]. On the other hand, the interface of layered system consisting of two types of materials is always imperfect bonding in most practical case due to various causes such as the microdefect and porosity processed in solid-state sintering, the aging of the glue, the corrosion of constituent materials, the accumulated damage or the local debond under harsh working circumstances, and so on [Lavrentyev and Rokhlin (1998); Vig and Ballato (1998)]. The imperfect bonding can greatly affect the performances of layered composites or devices. In this paper, we study the Rayleigh-type wave propagating in piezoelectric layered systems of cubic crystal. A declination angle between the direction of Rayleigh-type wave propagation and the crystallographic axis is considered. Effects of the mechanical and electrical interface parameters on dispersion curve and phase velocity are discussed based on the numerical results.

      2 Problem formulations and basic equations

      Consider a piezoelectric layered structure as shown in Fig. 1. The covering layer is a piezoelectric cubic crystal with finite thickness h and imperfectly bonding onto an isotropic dielectric substrate. Let the XYZ coordinate system aligns with the crystallographic axes of piezoelectric cubic crystal. Cut the piezoelectric crystal along a plane containing the Y-axis and rotating an angle θ with the XY plane so that a new rectangular Cartesian coordinate system x1x2x3can be obtained. We suppose that Rayleigh wave propagate along the x1-axis in the x1x3plane and hence a plane strain state can be produced. For convenience, the rotated coordinate system x1x2x3is adopted in the following analysis.

      Figure 1: Geometry of a rotated piezoelectric layered system

      According to the plane strain assumption, all field variables are independent on coordinate x2and the mechanical displacement components can be reduced to two-dimensional case with u1=u1(x1,x3,t) and u3=u3(x1,x3,t). The electric potential is φ=φ(x1,x3,t). According to the quasi-static approximation, in the absence of body forces and free charges, the equations of motion and the electric fieldequations in the sagittal plane are given by

      where σ11,σ13and σ33are the stress components, D1and D3are the electric displacements,ρ is the mass density. A superimposed dot represents the differentiation with respect to time t. Once u1, u3and φ are determined from appropriate conditions, the nonzero stresses σ11,σ13and σ33as well as the electric displacements D1and D3can be given through the following constitutive relations [Tseng (1970)]:

      where c11, c13, c33and c44are elastic constants, e31and e15are the piezoelectric constants,ε11is the dielectric constant. The above material constants are related to the corresponding quantities,,,,in the crystallographic coordinate system XYZ and can be obtained through tensor transformations as

      where θ is the cutting angle of piezoelectric cubic crystal.

      By substituting Eq. (2) into Eq. (1) we can obtain the governing equations for piezoelectric cubic crystal as

      Considering a dielectric substrate occupying 0>x3>-∞, the mechanical displacement and electric potential must satisfy the equation of motion and Laplace’s equation according to the general theory of elasticity. Let,anddenote the mechanical displacement and electric potential in the dielectric substrate, then the governing equations for dielectric media can be obtained as

      On the top of the piezoelectric layer, the mechanical traction-free conditions are

      At the same time, two kinds of electrical boundary conditions existing in practical applications are proposed to restraint the normal electric displacement or electric potential of the piezoelectric surface, i.e.

      for electrically shorted case.

      For a piezoelectric layered system, the interface between two constituents is usually assumed to be a perfect bonding interface for simplification which means that all the fields including the mechanical displacement, the stress, the electric potential and the electric displacement are continuous across the interface. However, the interface is always imperfect in most practical applications due to the various causes as mentioned in the previous section. It should be pointed out that not only the mechanical imperfection but also the electrical imperfection may occur at the interface of piezoelectric layered system. Jumps in mechanical or electrical quantities, or both, can occur at the imperfect interface [Li, Wei and Guo (2016)]. Instead of usual interface continuity conditions, we here consider a kind of interface possessing the special property of the mechanically compliant and dielectrically weakly conducting. In this case, the stresses and electric displacement are assumed to be continuous and the mechanical displacements and electric potential are discontinuous, that is

      for electrically open case and

      where KTand KNare the tangential and normal interface parameters describing the bonding strength of mechanical fields, respectively, while the parameter Kβcorresponds to the electrical imperfection. From Eq. (9), it is clear that the interface should be considered as perfect bonding when all the three interfacial parameters take infinite values. On the contrary, the covering layer and the substrate will be divorced from each other as the mechanically interfacial parameters KTand KNdecreasing to zero. Physically speaking, the interface can be considered as an insulated interface when the electrical parameter Kβequals to zero. In addition, the mechanical displacement and electric potential in the substrate tend to zero far from the interface along the negative x3direction,i.e.,

      3 General solutions and dispersion relations

      In this section, we search for the solutions of Rayleigh-type wave satisfying Eqs. (4) and(5) under the conditions (6)-(10). Based on the partial wave method [Cheng and Sun(1975)], the solution of Eq. (4) can be assumed as

      where k is the wavenumber, and v stands for the phase velocity of Rayleigh-type wave. A,B and C are unknown wave amplitudes, b is an undetermined parameter.

      Substituting Eq. (11) into Eq. (4), we can obtain

      For the above system of equations, to obtain a nontrivial solution of the resulting system,the determinant of the coefficient matrix must vanish, i.e.,

      Eq. (13) is a six-order equation in b with the phase velocity v as an unknown parameter.So for a given value of v, there are six roots satisfying Eq. (13) which denoted by bi(i=1-6). Substituting the six roots of bjinto the last two equations of (12), the amplitude ratios Bi=χiAiand Ci=ηiAican be obtained, where

      The complete solutions of piezoelectric crystal must contain all of the six roots of b, so the displacements and electric potential can be obtained as

      By applying the constitutive relations, the stresses and electric displacement can be obtained as

      For the dielectric substrate, the solutions to Eq. (5) have the following formulations

      Eq. (18) corresponds to the electric potential wave propagating in the dielectric substrate and decouples with the mechanical fields governed by Eq. (17). Since, the electric attenuation parametercan be solved form Eq. (18) as a pair of real roots with opposite signs, i.e.,. It means that the electric potential wave in the dielectric media decays away (for) or increases away (for) from the interface as x3 increases. Here, the positive rootshould be retained since the electric potential in the substrate must decay with increasing depth. To obtain a nontrivial solution of Eq. (17),the determinant of the coefficient matrix must vanish, i.e.,

      For a given value of v, the above equation yields four roots forin the substrate. The two positive values ofshould be retained in consideration of decaying wave modes in the substrate, which are denoted by. Thus, the complete solutions of dielectric substrate can be obtained as

      The stresses and electric displacement can be produced by taking account of the general elastic constitutive relations, as follows

      So far, the solutions for rotated cubic piezoelectricity and dielectric substrate are completely obtained. By taking advantage of the electro-mechanical conditions of the surface as well as the interfacial imperfection, a set of nine-order liner homogenous system with unknown constants An(n=1-8) andcan be obtained as

      For the existence of a nontrivial solution of Eq. (22), if and only if the determinant of the coefficient matrix must vanish, and this leads to the dispersion relation as

      4 Numerical results and discussions

      In this section, numerical calculations are carried out to show the propagation characteristic of Rayleigh-type waves in piezoelectric layered systems of cubic crystals with electrically and mechanically interfacial imperfections. The piezoelectric cubic crystal is considered as Indium Arsenide (InAs) and the substrate is selected as Diamond.The material parameters of the InAs in the crystallographic coordinate system XYZ are[Auld (1973)]:(1010N/m2),(1010N/m2),(1010N/m2),(C/m2),(10-11C2/Nm2), ρ=5700 (kg/m3). The material parameters of the Diamond are [Benetti, Cannatà, Pietrantonio et al. (2005)]:(1010N/m2),(1010N/m2),(1010N/m2),(10-11C2/Nm2),(kg/m3). For convenience of calculation, three non-dimensional parameters are introduced to describe the interfacial imperfection, that is, kt=KTh/c44, kn=KNh/c44, kβ=Kβh/ε11.

      4.1 Effect of electrical boundary condition on dispersion curve

      Dispersion curves of Rayleigh-type wave in InAs/Diamond layered structure under electrically open and shorted cases are respectively shown in Figs. 2(a) and 2(b), where θ=45。, kt=kn=kβ=5. It is found from Fig. 2 that phase velocity of the first mode starts from the Rayleigh wave velocity of Diamond (10937 m/s), monotonically decreases as the non-dimensional wavenumber increasing and tends towards the corresponding Rayleigh wave velocities of InAs (2237.34 m/s for electrically open circuit and 2237.29 m/s for electrically shorted circuit). The indistinct difference of the wave velocity at high frequency between the electrically open and shorted cases is because the piezoelectric constants of InAs are very small and the electro-mechanical coupling property is also weak. For the second mode and above, phase velocities uniformly start from the bulk shear wave velocity of Diamond (12322 m/s). These primary propagation characteristics of Rayleigh-type wave, e.g. the starting wave velocity at small wavenumber and the approaching wave velocity in the range of higher wavenumber, completely coincide with those given by Rose [Rose (1999)]. This coincidence can verify the validity of our analytical solution and numerical procedure. In view of the insignificant effect of electrical boundary conditions on dispersion curve and wave velocity, we thus focus on electrically open case in the following discussions.

      4.2 Effect of cutting angle on phase velocity

      Fig. 3 shows the effect of cut orientation on phase velocity of the first mode for selected values of non-dimensional wavenumbers. It is clear from Fig. 3 that phase velocity of Rayleigh-type wave is symmetric with respect to θ=45°. The wave velocity reaches the maximum value at θ=45° while minimum for the cases of θ=0°and 90°. This means that if we appropriately set the cut orientation of InAs crystal along the degree of 45° an optimal propagation behavior of Rayleigh-type wave can be achieved. For a SAW device,operating under a proper wave speed cannot only be an effective help for enhancing sensitivity, but also for the miniaturization of device.

      4.3 Effect of interfacial imperfection on phase velocity

      The effects of the tangential and normal interface parameters ktand knon phase velocity of the first mode are illustrated in Fig. 4, where the cutting angle θ is selected as 45。. It can be seen from Fig. 4 that both the tangential and normal imperfections consistently weaken the wave velocity of Rayleigh-type wave. Physically speaking, wave propagation is the propagation of mechanical energy. The interface has higher transmission capability of mechanical energy when it is mechanically perfect bonding. On the contrary, a mechanically imperfect bonding represents a deformable interface which has less stiffness comparing with a perfect interface. The degenerated interface can lead to the reduction of wave velocity. It is observed from Fig. 4 that the tangential interface parameter has smaller effect on wave velocity comparing with the normal imperfection.This is because the tangentially imperfect bonding only results in sliding contact, while the normal imperfection maybe leads to an extreme case of interfacial detachment and hence strongly affects the propagation behaviors of Rayleigh-type wave. It is also found that the interface can be regarded as a perfect bonding when the non-dimensional tangential parameter ktis larger than about 20 and the normal parameter knabout 40. On the other hand, the mechanical imperfection has great effects on phase velocity at relative small wavenumbers. But for higher frequency or large wavenumber, e.g., kh>3, the influence of mechanical imperfection on phase velocity gradually decays and thus the distinction between normal and tangential parameters turns to disappearance.

      Fig. 5 shows the effect of the electrical interface parameters kβon phase velocity, where θ=45°. It can be seen from Fig. 5 that the electrical imperfection has very less effect on phase velocity comparing with the mechanical imperfection shown in Fig. 4. According to our calculation, the electrical imperfection makes a small reduction of wave velocity.When the non-dimensional imperfection parameter kβdecreases from 10 to zero, the decrease in phase velocity of Rayleigh-type wave is about within one decimal places.This is because the mechanical interaction at the interface of piezoelectric layer and dielectric substrate plays a dominant role in the piezoelectric coupling system during the propagation of Rayleigh-type waves. Under this special consideration and for the InAs/Diamond layered system, we can ignore the effect of electrical imperfection on wave velocity and thus focus on the mechanical imperfection in the design and application of InAs-based acoustic wave device.

      5 Conclusions

      Propagation of Rayleigh-type waves in layered structures consisting of a rotated piezoelectric cubic crystal imperfectly bonding onto a dielectric substrate is investigated in this paper. The imperfect interface is assumed as mechanically compliant and dielectrically weakly conducting condition. The exact dispersion relations for electrically open and shorted boundary conditions are derived in closed form. The numerical results show that: 1) the phase velocity is symmetric with respect to the cutting angle of 45° and can achieve the maximum propagation speed; 2) the electrical boundary conditions applied on the surface of the layered system have less effect on dispersion curves; 3) the mechanical imperfection can significantly affect the dispersion curves and then lowers the phase velocity because the deformable interface makes the interfacial stiffness weaken. Further, the phase velocity is more sensitive to the normal imperfection comparing with that of tangential; 4) the electrical imperfection makes a relatively small reduction of phase velocity of Rayleigh-type wave comparing with the mechanical imperfection. These results can offer some fundamentals for understanding of piezoelectric semiconductor as well as the basis for design and application of piezoelectric SAW devices.

      Figure 2: Dispersion curves of Rayleigh-type wave in InAs/diamond layered structure,where θ=45°, kt=kn=kβ=5. (a) electrically open case, (b) electrically shorted case

      Figure 3: Effects of the cut orientation on phase velocity, where kt=kn=kβ=5

      Figure 4: Effects of the mechanical interface parameters kt , kn on phase velocity, where θ=45。, kt in solid line and kn in dash line

      Figure 5: Effect of the electrical interface parameter kβ on phase velocity, where θ=45°

      Acknowledgements:This work is supported by the National Natural Science Foundation of China (Nos. 11872041 and 11272221). Guoquan Nie also greatly acknowledges the Support Plan for One Hundred Outstanding Innovation Talents in Colleges and Universities of Hebei Province of China (SLRC2017052).

      Appendix

      The non-zero components of matrix S for electrically open case:

      By replacing the S(9,i) with eibkhiηthe dispersion relation for electrically shorted case can be obtained.

      博客| 三明市| 五大连池市| 伊金霍洛旗| 怀仁县| 清涧县| 湄潭县| 南投县| 西乌| 陈巴尔虎旗| 巴南区| 芦山县| 德格县| 宜良县| 上林县| 仪陇县| 拉萨市| 永福县| 长沙县| 巩义市| 彭山县| 宜都市| 孙吴县| 拜泉县| 平遥县| 象州县| 光泽县| 大同县| 黄陵县| 醴陵市| 多伦县| 汉阴县| 开封县| 米易县| 金华市| 房产| 涪陵区| 神农架林区| 山阴县| 盘山县| 兰考县|