• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Plastic instability and texture modification in extruded Mg-Mn-Nd alloy

    2022-07-14 08:55:50SngKyuWooRishengPeiTllAlSmmnDietmrLetzigSngongYi
    Journal of Magnesium and Alloys 2022年1期

    Sng Kyu Woo, Risheng Pei, Tll Al-Smmn, Dietmr Letzig, Sngong Yi

    aMagic-Magnesium Innovation Center, Institute for Materials and Process Design, Helmholtz-Zentrum Geesthacht, Geesthacht 21502, Germany

    b Institut für Metallkunde und Materialphysik, RWTH Aachen University, Aachen 52056, Germany

    Abstract Even though Mg alloys containing Mn and rare earth elements lead to higher ductility and lower yield asymmetry due to the weak texture after extrusion, plastic instability, commonly known as the Portevin-Le Chatelier (PLC) effect, causes unexpected fragility in the service environment.In the present study, the PLC phenomenon and texture development during the deformation of Mg-Mn and Mg-Mn-Nd extruded alloys were investigated under various temperatures and strain rates.The addition of Nd causes not only texture weakening but also severe PLC phenomenon.The PLC phenomenon was significantly affected by the temperatures and the strain rates, which causes a difference in mechanical properties and development of texture.In the conditions of high temperature and low strain rate, the strength increased while the elongation decreased significantly, and obvious PLC phenomenon with severe serration and negative strain rate sensitivity.The initial texture was maintained even after deformation only under severe PLC conditions, and this is due to the restriction of basal slip and suppression of lattice rotation in PLC conditions.The series of results indicate that the PLC phenomenon causes a reduction of formability even at high temperature.

    Keywords: Magnesium; Plastic instability; Portevin-Le Chatelier effect; Manganese; Neodymium; Texture.

    1.Introduction

    It has been widely accepted until recently that the microalloying of rare earth (RE) elements and/or Ca to Mg forms a significantly weaker texture during thermo-mechanical treatments, in comparison to commercial AZ-based alloys [1-8].The weak texture, e.g.a wider distribution of (0001) basal poles, allows the activation of dislocation slip on the basal plane, which is the dominant deformation mechanism of Mg alloys.The texture weakening with altering the basal-type orientation to a more randomized orientation distribution leads to an improved room temperature (RT) ductility and formability, reduced tensile/compressive anisotropy, and a balanced strain hardening.In addition to the texture weakening, the addition of RE and Ca affects the activities of various deformation mechanisms of the Mg alloys.Recent studies showed that Mg alloys containing Mn and a single RE element have an obvious trend to form a weak texture after extrusion.These weakened texture profiles lead to higher ductility and reduced asymmetry in tensile and compressive yield strengths[5,9,10].

    Plastic instability, commonly known as the Portevin-Le Chatelier(PLC)effect,appears as unstable plastic flow during mechanical tests of structural materials such as steel, Al, Cu,and Mg based alloys.The occurrence of instability phenomena manifests in the form of ‘serration flow’ or ‘jerky flow’in the plastic range, within a specific range of strain rate and temperature [11-13].The PLC phenomenon has a diverse influence on various material properties.It increases the flow stress, maximum tensile strength, and work hardening rate,while the ductility decreases with decreasing strain rate sensitivity (SRS) coefficient and fracture toughness [11].Thus,it causes an unexpected vulnerability in the service environment or during the thermomechanical processes.This phenomenon has been extensively studied to understand the un-derlying mechanisms for engineering materials, such as steel,Cu and Al alloys.Recently, the direction of research has been extended to Mg alloys.Although several mechanisms have been proposed so far, the mechanism of PLC and its influence on the mechanical properties have not yet been clearly identified.Therefore, a further systematic study is still required according to the characteristics of each alloy system because various factors act in combination depending on the alloying element.

    Recent studies reported the occurrence of the PLC phenomenon in Mg alloys, especially in Mg alloys containing RE elements [14-16].Nevertheless, there is still a lack of understanding the relationship between the plastic instability and microstructure and/or texture of Mg-Mn alloys.Even though the Mg-Mn-RE alloys obviously have the advantages from the texture weakening after extrusion, there is a concern that the properties are severely deteriorated due to the plastic instability at certain deformation conditions.The present study aims to investigate the PLC phenomenon in Mg-Mn and Mg-Mn-Nd extruded alloys under various temperatures and strain rates.The focus of the present study is laid to verify the correlation between the PLC phenomenon and texture evolution.The deformation conditions, at that the PLC effect is evident, were selected, and then the correlation between the mechanical behavior and the resulting deformation texture was analyzed in detail.

    2.Experimental procedure

    Pure Mg ingot and Mg-Mn and Mg-Nd master alloys were used for casting.The raw materials with nominal compositions of M1 (Mg-1 wt.%Mn) and MN11 (Mg-1 wt.%Mn-1 wt.%Nd) were molten in a steel crucible under a protective gas atmosphere.The melt was poured into a cylindrical steel mold preheated at 500 °C and quenched with the mold in water.After homogenization heat treatment for 16 h at 450 °C,the billets for extrusion were machined to 49 mm in diameter.The machined billets were preheated to 300 °C and then directly extruded through a circle die of 8 mm in diameter.The extrusion ratio and ram speed were 37.5:1 and 2.5 mm/s,respectively.Table 1 shows the chemical composition of M1 and MN11 alloys measured by spark optical emission spectroscopy (OES).

    Table 1Chemical composition of Mn-based alloys measured by spark OES.

    The specimens for microstructural observation were cut from the extruded bars and mounted using epoxy resin.The mounted specimens were mechanically ground using SiC papers up to #2400 grit and then polished using 3 μm diamond paste and water-free oxide polishing suspension.The polished specimens were etched using a mixed solution of 1 mL of nitric acid, 20 mL of distilled water, 20 mL of acetic acid, and 70 mL of ethylene glycol.The microstructures of specimens were observed using an optical microscope (OM, Nikon Optiphot 200).

    The global texture was measured using an X-ray diffractometer (XRD, PANalytical X’Pert PRO MRD) with Cu Kαradiation.A beam size of 2 × 1 mm2 was employed to measure 6 pole figures, the (100), (0001), (101), (102),(110), and (103) up to a tilt angle of 70°.Normalized and background-corrected pole figures were used to calculate the orientation distribution function by using an open source code MTEX [17].The complete pole figures and inverse pole figures in the extrusion direction were calculated to present the texture.

    The mechanical properties of the extruded alloys were examined using round-shaped specimens with a gauge length of 20 mm and a diameter of 4 mm.Tensile tests were carried out using a universal testing machine (Zwick, Z050)equipped with a heating furnace at various temperatures (RT and 150 °C) and strain rates (10?2/s, 10?3/s, and 10?4/s)in the extrusion direction.Prior to the mechanical loading,the specimens were preheated at the testing temperature for 10 min to ensure temperature uniformity over the specimen.After the tensile test, the specimens were immediately quenched in a water bath at RT in order to avoid the microstructure change due to slow cooling.Furthermore, strain rate jump tests were carried out to determine the SRS,mvalue.The strain rates were increased in 5 steps from 10?4to 10?2/s at each testing temperature.

    Electron backscatter diffraction(EBSD)was carried out using a field emission gun scanning electron microscope (Zeiss,Ultra 55) equipped with an EDAX/TSL EBSD system with a Hikari detector.Longitudinal sections of the tensile specimens were ground and mechanically polished.Then, electrolytic polishing was carried out using a Struerse AC2 solution.EBSD measurements were performed at an accelerating voltage of 15 kV and a step size of 0.3 μm.The acquired EBSD data was analyzed using MTEX and TSL OIM analysis software.

    3.Results

    Fig.1 shows the optical micrographs of the as-extruded M1 and MN11 alloys.Both alloys show a fully recrystallized microstructure with equiaxed grains, resulting from dynamic recrystallization during extrusion.The M1 alloy shows an inhomogeneous grain size distribution, and the average grain size is classified into two groups: 14.9 ± 1.1 μm and 36.2 ± 1.0 μm.The MN11 alloy has a relatively uniform grain size distribution, and the average grain size is 8.8 ± 1.0 μm.The finer grain structure in the latter is attributed to the Nd addition.Extruded Mg-Mn-Nd alloys contain a large amount of Nd solute, the Mg-Nd intermetallics and thermally stable Mn-containing particles [5,9,10,18].The addition of Nd causes a change in the fraction and shape of the Mn-containing particles.These microstructural changes effectively inhibit grain growth.

    Fig.1.Microstructure of extruded (a) M1 and (b) MN11 alloys observed using an optical microscope.

    Fig.2.The recalculated (100) and (0001) pole figures (a, b) and inverse pole figures (c, d) of the extruded M1 (a, c) and MN11 (b, d) alloys obtained using X-ray diffraction.

    Fig.2 shows the recalculated (100) and (0001) pole figures and the inverse pole figures of the extruded M1 and MN11 alloys obtained from XRD measurements.The M1 alloy shows a strong ‘basal-type’ texture in which the majority of the grains have the basal planes parallel to the extrusion direction (ED), Figs.2(a) and (c).Accordingly, the inverse pole figure shows high intensities along the arc between<100>and<20>poles.The<100>fiber component parallel to the ED, i.e.main deformation axis, is commonly formed by round extrusion of commercial Mg alloys [5,19,20].The addition of Mn is known to promote the formation of the basal-type texture of Mg alloys [20,21].The MN11 alloy shows a distinct texture with the basal poles largely tilted away from the ED, and the main texture components are represented by<201>and<33>components in the ED,Figs.2(b) and (d).The MN11 has a much weaker texture intensity than the M1 alloy, 2.7 m.r.d.(multiple of random distribution) and 4.6 m.r.d., respectively.Texture weakening has been reported in the Nd containing Mg alloys at a wider range of extrusion conditions such as temperature and speed, whilethe distribution of main components slightly varies with the extrusion conditions [5,9].Such texture with the tilted basal poles from the ED are classified as ‘RE texture’ components[5,9,10,19,21,22].

    Fig.3.(a) Tensile stress-strain curves obtained at different temperatures and strain rates for M1 alloys, and the magnified stress-strain curves of the selected area at (b) RT and (c) 150 °C.

    Fig.4.(a) Tensile stress-strain curves obtained at different temperatures and strain rates for MN11 alloys, and the magnified stress-strain curves of the selected area at (b) RT and (c) 150 °C.

    Tensile stress-strain curves of the M1 and MN11 alloys obtained at different temperatures, RT and 150 °C, and initial strain rates, 10?2/s, 10?3/s, and 10?4/s, are shown in Figs.3 and 4, respectively.Table 2 shows the yield strength (YS), ultimate tensile strength (UTS), uniform elongation (UEl.) and fracture elongation (FEl.) corresponding to the flow curves under each condition measured in Figs.3 and 4.In the case of the M1 alloy, UTS and UEl.were measured in the curve after the yield point, to exclude abnormal peaks observed at the initial curve.Fig.3(b) and (c) show a magnified view of the flow curve in the selected area at RT and 150 °C, respectively.The selected area was determined near the UTS where the serration was prominent in order to compare the different serration behaviors according to testing conditions.At RT, theM1 alloy shows relatively high stress and low elongation.At 150°C,the fracture elongation significantly increased,accompanying the decrease in the strength.The distinct mechanical properties at different testing temperatures result from the difference in the dominant deformation mechanisms.While the dislocation slip is the main deformation mechanism at RT,thermally activated mechanisms, such as grain boundary sliding (GBS), dynamic recrystallization, the occurrence of creep driven by dislocation climb or diffusion, are responsible at high temperature [23,24].In the case of the M1 alloy, the flow stress was significantly reduced and the elongation is significantly increased, as the constraint of activating dislocation slip due to the strong basal texture at RT is alleviated by the reduced critical resolved shear stress (CRSS) values at 150 °C.By comparing the flow curves at different strain rates, there is a clear tendency that the flow stress increases as the strain rate increases, and the fracture elongation does not show a large difference with the variation of strain rates.Noteworthy is that serration is observed in some of the flow curves of the M1 alloy [Figs.3(b) and (c)].While the serration of the flow curve is almost negligible at RT, it becomes remarkable at 150 °C and a low strain rate of 10?4/s.

    Table 2Tensile mechanical properties along the ED measured for the M1 and MN11 alloys at different temperatures (YS: yield strength, UTS: ultimate tensile strength, UEl.: uniform elongation and FEl.: fracture elongation).

    The counterpart flow curves of the MN11 alloy at the same testing conditions are presented in Fig.4.In the MN11 alloy with the RE texture components, as shown in Fig.2(b)and (d), the activation of dislocation slip is relatively easy in comparison to the M1 alloy.When a tensile load is applied in the ED, Schmid factor for basal slip is initially high due to the tilted basal plane to the loading axis.Easier activation of the basal slip, as a result of a geometrical advantage, is generally accepted to promote enhanced ductility [14,21].The flow curves of the MN11 alloy with those properties differ from those of the M1 alloy.The tendency of increasing the stress as the strain rate increases is similar to that of the M1 alloy, but unlike the M1 alloy, the elongation also tends to decrease as the strain rate increases.At RT, similar to the M1 alloy, significant serration was not observed [Fig.4(b)].On the other hand, the results at 150 °C are noteworthy.Compared with the results at RT, the stress decreased slightly,but the elongation also decreased.In addition, evident serrations were observed at strain rates of 10?3/s and 10?4/s [cf.inset in Fig.4(a)].In Fig.4(c), the serration observed at a strain rate of 10?4/s is clearly much more prominent compared to other conditions.In the latter case of severe serration, the difference in stress between the highest and lowest serration points,Δσ, ranged from 5 ≤Δσ≤10 (MPa).It is clearly distinguished from the weak serrations under other conditions withΔσof 1 or less.As shown in Fig.4(a) and(c), the serration behaviors at 10?3/s and 10?4/s are classified into different types [11,16,25,26].‘TypeA’ band has a relatively small amplitude, but a large amplitude may appear periodically in the long range.It is can be subdivided according to these patterns.‘TypeB’ band characteristically a large amplitude accompanied by a stress drop in very short periods.This pattern is observed periodically over the long range.‘TypeC’ band results in a stress drop of large amplitude and a pseudo-periodic pattern is formed with large period.The serration at 10?3/s corresponds to the typeA, while a mixed type of serration similar to typeBis observed at the strain rate of 10?4/s.The variation of the serration type is attributed to the temperature increase, from typeAto typeBand typeC.TypeAserration is often observed at high strain rates or low temperatures, while typeCserration is observed at low strain rates and high temperatures.The type of serration is found to depend on the ’pinning nature’ between the dislocations and solute atoms according to varying strain rate and temperature.The pinning and unpinning abilities of the solute atoms to the dislocation is the predominant factor of the diverse serration behaviors.Unlike at RT, the stress increased and the elongation decreased significantly as the strain rate decreases.It is known to be due to the PLC effect associated with severe serration, which is prominently observed in the high temperature flow curve [11-13].

    The degree to which the properties vary depending on the strain rate is expressed as SRS, m-value, which is considered an important parameter to explain better formability at higher temperatures [27,28].SRS is influenced by the alloy composition and microstructural factors such as grain size, texture and twinning and experimental conditions such as strain rate and temperature[22,29-32].In general,in a commercial alloy such as AZ31 alloy, them-value is in the range of 0 to 0.01,and the m-value tends to increase with increasing temperature and strain rate [29,30].The SRS parameter ‘m’ is expressed as Eq.(1.1), whereσ1 andσ2 are the flow stresses at each strain rates ˙ε1 and ˙ε2, and ‘n’ is the strain sensitivity coefficient [27,33].

    The most common way to measure the SRS is to carry out each tensile test at different constant strain rates, as shown in Figs.3 and 4.However, due to deformation history and recovery, the microstructure may change for each test, and it affects the calculated m-value.Alternatively, SRS is of-ten evaluated by the strain jump test technique [31,34,35], or a stress relaxation test [36].These tests have the advantage of being performed with a fixed specimen microstructure, so that SRS can be accurately and reliably measured.Fig.5(a)shows the variation in flow stress according to the strain rate change, which was measured via the strain rate jump tests.Fig.5(b) shows the result of m-values calculated from the data sets shown in Fig.5(a).While the stress increase with the strain rate is obvious at RT in both alloys, the SRS of the MN11 alloy at high temperature varies with the range of the strain rates.At the range of the higher strain rate the SRS is positive, while a negative SRS is shown at the low strain rate range.It clearly indicates a negativem-value, unlike the other three conditions, which all have positive values in Fig.5(b).In particular, the trend is more pronounced at a low strain rate.

    Fig.5.(a) Variation in flow stress with strain rate in each condition measured via the strain rate jump test, and (b) calculated m-value of the measured data in (a) with a variation of strain rates of M1 (black) and MN11 (red) alloys at RT (solid line) and 150 °C (dash line) (For interpretation of the references to color in this figure legend, the reader is referred to the web version of this article.).

    Fig.6 shows the EBSD orientation maps measured from longitudinal sections of the tensile samples of the MN11 alloy fractured at different testing conditions.The orientation maps and inverse pole figures were measured at two different areas of the fractured samples, one at the area nearby the fracture surface (F) and the other at the uniformly deformed area (U).For the uniformly deformed area (U), an area where necking did not occur at least 5 mm away from the fracture tip (F)was selected to have a deformation similar to that of UEl.The examined alloys have similar values of UEl.under all conditions, Table 2, and they are considered to have undergone the same deformation at the area (U).The PLC phenomenon is most prominently observed at the testing condition of 150 °C and 10?4/s.At the testing condition of 150 °C and 10?2/s,the PLC phenomenon significantly diminished as the strain rate increases, and the sample tested at RT and 10?4/s is also almost free from the PLC phenomenon with the temperature decrease.The deformation degree should be relatively large at the area(F),where elongated grains along the loading direction are observed.In general, the deformation of commercial AZ-based alloys at elevated temperature accompanies dynamic recrystallization (DRX) and grain growth.The grain structure at the area (F) in Fig.6, does not show traces of DRX, which is believed to be restricted at 150 °C in the examined alloy.At the area near the fracture surface (F) of the sample tested at 150 °C and 10?4/s, the<201>component in the loading direction is maintained from the initial texture.On the contrary, the specimens with weak serration of the flow stress curves, i.e.tested at 150 °C and 10?2/s, and at RT and 10?4/s, clearly show the development of<100>component in the loading direction.The same comparison was made in the uniform deformation region (U), i.e.away from the fracture tip and necking zone.The specimen tested at 150 °C and 10?4/s maintained the initial texture with the intensity distribution along the arc from<101>and<201>to<22>and<21>components.Both of the other specimens did not fully maintain the initial texture.However, in the 150 °C and 10?2/s specimen, only a slight change was observed, whereas at RT and 10?4/s, it deviated from the initial texture and showed a complete<100>component.A change in texture in terms of intensity of<100>component was listed in the following order.Initial state ≈150 °C and 10?4/s (U)<150 °C and 10?4/s (F) ≈150 °C and 10?2/s(U)<RT and 10?4/s (U) ≤150 °C and 10?2/s (F) ≈RT and 10?4/s (F).This texture variety has a similar order to the PLC strength.

    4.Discussion

    4.1.Changes in microstructure, texture, and PLC effect according to Nd addition

    The addition of Nd to the Mg-Mn alloy results in the grain refinement and the texture weakening accompanying the formation of RE texture components (Figs.1 and 2).The possible mechanisms for grain refinement were reported that fineand thermally stable Mn and Nd containing phases inhibit the grain growth by pinning [9,10].The underlying mechanism of texture weakening by the addition of RE is still controversial.Diverse mechanisms have been reported by many research groups, e.g.nucleation of recrystallization at shear or twin bands [1,7,9,21,37,38], enhanced non-basal slip activity [39,40], and the orientated grain growth controlled by solute drag or particle pinning along the grain boundaries[7,8,41-43].Of course, it is likely that several mechanisms act simultaneously.Nd is considered as an effective texture modifier among REs, and is known to contribute to an increase in ductility and a decrease in yield anisotropy through texture weakening[5,9,10].Such improvement of the mechanical properties of the Mg-Mn alloy by the Nd addition is supported by the stress strain curves at RT, Figs.3 and 4, of the present study.As such, the addition of Nd is considered to be a promising alloying element to achieve the desired mechanical properties by means of microstructure and texture modification.Nevertheless, it should be noted that severe serration of the stress strain curves takes place at a specific temperature and strain rate range, as shown in Fig.4.The M1 alloy does not show serration in the flow curves at RT, while it is partially observed at 150 °C and 10?4/s, Fig.3(c).In the MN11 alloy, a weak serration is observed already at RT,and the occurrence of the serration is severe at 150 °C, especially at the low strain rate.With decreasing the strain rate,the flow stress increases and the elongation decreases significantly in MN11 alloy at 150 °C, which is clearly depicted by a negative SRS(nSRS)value under the corresponding loading conditions.As such, nSRS is well-known as an indication of dynamic strain aging (DSA), which is considered as a major mechanism of the PLC phenomenon [11,26,33,44].DSA is defined as the interaction between the mobile dislocations and the diffusing solute atoms.According to this mechanism,the mobile dislocations act as a carrier of plastic deformation and move unsteadily between obstacles.Recently, extensive theoretical studies of the PLC effect and its mechanisms have been reported in the literature, including various novel simulations and insights into the nature of nucleation and the motion of the strain bands [33,45,46].In other studies, it has been quite discussed that DSA cannot explain all cases of nSRS [11,33,44,47].H?hner [48, 49]suggested that in order to satisfy nSRS, the DSA and the long-range dislocation interaction does not occur independently, but must be combined with each other.In this case, an unstable plastic flow is observed.When Nd is added, a large amount of Nd solute is present in the extrusion bar [9, 10].In order to control the movement of dislocation via interaction of Nd solute with mobile dislocation, diffusion of Nd solute and slow dislocation movement are required.At 150 °C and low strain rate of 10?4/s this condition is likely to be satisfied, as shown in Fig.4(a).Hence, it is reasonably inferred that DSA caused by Nd solute induces nSRS and causes PLC phenomenon.Several recent studies have reported DSA and PLC phenom-ena occurring in Mg alloys containing Nd such as Mg-Zn-Nd[15,16]and Mg-Y-Nd [32].

    Fig.6.The EBSD orientation maps from longitudinal sections of alloys and the corresponding inverse pole figures for the area nearby the fracture surface(F) and uniformly deformed area (U) after tensile test under each condition of MN11 alloy; (a) 150 °C_10?2/s, (b) 150 °C_10?4/s, and (c) RT_10?4/s.

    4.2.Correlation between PLC phenomenon and texture according to temperature and strain rate in MN11 alloy

    There is a consensus that the addition of RE to the Mg alloy significantly affects the evolution of the microstructure during deformation at high temperatures.This is often explained by the retardation of dynamic recovery (DRV) and DRX due to solute drag or boundary pinning [1,7,21,39].This is very important for altering the basal-type texture,as the DRX kinetics is controlled by the amount of stored energy in the deformed microstructure and nucleation during static recrystallization.The results of Figs.3-6 show the interrelationship among the microstructural change caused by the addition of Nd, mechanical properties, texture development and PLC phenomenon.It is obvious that there is a very close relationship between the development of the texture and the occurrence of PLC phenomenon [46,50,51].The results of the present study clearly show that the texture and PLC phenomenon are strongly dependent on the alloying element and experimental conditions.Even in the case of the same initial texture, the resulting texture from the tensile deformation varies in correspondence with the PLC occurrence.The tensile specimens deformed at three different conditions corresponding to the degree of serration show distinct deformation textures, Fig.6.Lattice rotation during uniaxial tension commonly results in the formation of<100>texture component, as shown in Fig.6(a)and (c).However, in the specimen deformed at 150 °C and 10?4/s, Fig.6(b), the texture rarely changed and the initial texture was maintained.In other words, plastic spin was suppressed by some factors.It is also believed that the factor is related to the observation of strong serration under this condition.

    In order to analyze the slip system that is dominantly activated during deformation under each condition in-grain misorientation axes (IGMA)analysis was conducted based on the EBSD results.This analysis provides insight into the local rotation of the crystal lattice due to dislocation slip [39,52,53].For example, deformation due to prismatic<a>slip induces lattice rotation around the<0001>axis,while basal<a>and pyramidal II<c + a>slip cause the lattice rotation around<100>and pyramidal<a>slip around<102>axes.In this work, the misorientation angle of 0.5°-2° was used in the IGMA analysis.Specimens deformed under conditions of RT and 10?4/s, 150 °C and 10?4/s, and 150 °C and 10?2/s which show a clear difference in texture as shown in Fig.6, were analyzed and compared.The grains with a GOS (grain orientation spread) of 1° or more were selected for the IGMA analysis.Fig.7 shows the IGMA distribution of the specimen deformed at RT and 10?4/s, showing weak serration.In Fig.7, among the grains of GOS>1° in the uniformly deformed area (U), the IGMA analysis was performed on the grains selected according to the orientation.The grain orientations showing strong intensity in Fig.6 were analyzed by dividing into two IGMA types.Fig.7(a) shows the grains having their<201>poles in the ED, and the grains with<100>poles in the ED are shown in Fig.7(b).In the case of RT and 10?4/s specimen, a similar number of grains locate at<201>and<100>poles.The IGMA for the grains in Fig.7(a) show a relatively high concentration in the<0001>axis.Therefore, it is considered that the prismatic<a>slip was predominantly activated.On the other hands,<100>grains selected IGMA in Fig.7(b) show a relatively high concentration in the<100>axis, which means basal slip was predominantly activated for these selected grains.These results show that the activated slip system differs according to the grain orientations, and thus various slip systems are activated upon deformation.In the case of RT and 10?4/s specimen in Fig.7, activation of prismatic slip and basal slip leads lattice rotation, resulting in the strong intensity of<100>poles after fracture as shown in Fig.6(c).Fig.8 shows IGMA distributions of the specimen deformed at 150 °C and 10?4/s,which shows strong serration.In this specimen, a large number of deformed grains are selected at the<201>poles,while only a few grains locate at the<100>poles.The IGMA for the grains in Fig.8(a) show a relatively high concentration in the<0001>axis.Therefore, it is considered that the prismatic<a>slip was predominantly activated with other non-basal slips.Even though only a small number of grains in Fig.8(b) were analyzed, a high concentration was clearly distinguished in the<0001>axis.That is, the same IGMA is identified in the two different grain orientations in this specimen.It is indicated that activation of basal slip is strongly restricted regardless of grain orientations in 150 °C and 10?4/s specimen with strong serration.This could be related to the selective segregation of Nd solute atoms on the basal plane around basal dislocations.By DSA, the basal slip is hardened and the activation of non-basal slip is promoted at 150 °C and 10?4/s.That is the PLC effect contributes to maintaining the initial RE texture by suppressing lattice rotation during deformation.In addition, the reduction of the CRSS of non-basal slip at 150 °C should be also one of the reasons.This may also explain the result of relatively weak<100>pole of another specimen at 150 °C, in Fig.6(a),compared to RT specimen.Fig.9 shows IGMA distributions of the specimen deformed at 150 °C and 10?2/s, which also shows relatively weak serration.Similar to 150 °C and 10?4/s specimen in Fig.8,the high concentration in the<0001>axis is shown, but the grains with<100>poles in the ED show high concentration in the<100>axis, similar to RT and 10?4/s specimen in Fig.7.This means that more basal slip is activated with prismatic<a>slip in this specimen, and it may indicate a relative dominance of the effect of temperature rather than that of strain rate.However, it is believed that the lower strain rate contributes to a stronger suppression of basal slip, so that lattice rotation is more restricted in the 150 °C and 10?4/s specimen.

    Another important deformation mechanism is GBS, especially at elevated temperature and moderate strain rate.The occurrence of the GBS, especially the GBS induced by the grain boundary diffusion, is considered to weaken the textureby accepting the grain rotation during deformation [54,55].The GBS is in general accompanied by fine grains formed in the vicinity of grain boundaries as a result of DRX [56,57].However, as shown in Fig.6, the samples of the present study do not show such DRXed microstructures, and the relatively high flow stress is observed during the deformation of MN11 alloy at the elevated temperatures.These observations are not manifested in the occurrence of the boundary diffusion-based GBS, such that the texture formation is not caused by the GBS.

    Fig.7.Inverse pole figure maps (top) and corresponding IGMA analysis results (bottom) on the uniformed area (U) of RT_10?4/s specimen corresponding in Fig.6(c); (a) and (b) represent the selected grains from inverse pole figure marked as purple and blue, respectively (For interpretation of the references to color in this figure legend, the reader is referred to the web version of this article.).

    Lattice rotation during the deformation is also influenced by the secondary phases[58,59].Table 3 and Fig.10 show the fraction of stable phases of the M1 and MN11 alloys calculated using the thermodynamic software PANDAT.While the fractions of the Mn-containing phases are not significantly different in both alloys, the fraction of the Nd-containing phases in the MN11 alloy is much higher than the Mncontaining phase.At 450 °C, all Nd-containing phases are dissolved, but thermally stable Mn-containing phases are not completely dissolved.During the extrusion and air-cooling the Mn-containing phase is mostly precipitated, whereas theNd-containing phases are not fully precipitated and a large amount of Nd solute is dissolved in the as-extruded bars.Such a large amount of dissolved Nd solute can induce the PLC by interaction with mobile dislocations.The fraction,distribution, and shape of the Mn and Nd-containing phases change during high temperature deformation [9,10,60,61].Especially the diffusion and precipitation of the Nd-containing phase is facilitated when the sample is exposed to the thermal environment for a long time during the low strain rate defor-mation at 150 °C.These results elucidate that the dynamic microstructural change during deformation affects not only the PLC phenomenon but also the development of the texture.It seems that the large number of dynamic precipitates formed in this way maintained the initial texture by suppressing the lattice rotation.In order to suppress lattice rotation by the precipitate, a condition in which a very slow deformation rate is applied for a long time in a thermal environment must be satisfied, which corresponds very well to the condition for the occurrence of the PLC phenomenon.From this point of view, not only the interaction between the Nd solute atom and the dislocation, but also the interaction between the dislocation and the precipitate can be regarded as the possible mechanism for the PLC phenomenon of the Nd-containing alloys.

    Table 3Fraction of stable phases of M1 and MN11 alloys at difference temperatures calculated by thermodynamic calculation software PANDAT (in wt.%).

    Fig.8.Inverse pole figure maps (top) and corresponding IGMA analysis results (bottom) on the uniformed area (U) of 150 °C_10?4/s specimen corresponding in Fig.6(b); (a) and (b) represent the selected grains from inverse pole figure marked as purple and blue, respectively (For interpretation of the references to color in this figure legend, the reader is referred to the web version of this article.).

    The dislocation density remaining in the deformed material, i.e.geometrically necessary dislocations (GNDs), can be visually expressed using a kernel average misorientation(KAM) map [39,62].Fig.11 and Table 4 show the KAM map and the relative fraction according to the misorientation angle interval of area (U) in Fig.6 in each specimen.In general, the deformed grains have a relatively high KAM due to the high density of GNDs, and low KAM in recrystallized grains [63].As shown in Fig.11, all specimens show uniform deformation.The sample deformed at RT and 10?4/s,Fig.11(c),shows the highest KAM value.The other two specimens have relatively low KAM values because they were deformed at 150 °C.Comparing the specimens deformed at different temperatures, the 150 °C and 10?2/s specimen in Fig.11(a) shows a relatively larger fraction of a lower KAM value overall.In general, localized misorientation decreases as the deformation temperature increases, due to the increase in the DRV fraction [64], which corresponds well with the results of Figs.11(b) and (c).When the strain rate is low,localized misorientation decreases, because DRV occurs during deformation at low strain rate [64,65].Accordingly, it is expected that the 150 °C and 10?4/s specimen should have a lower KAM value than the 150 °C and 10?2/s specimen.But the results in Figs.11(a) and (b) do not correspond to this,but rather show a higher KAM value in 150 °C and 10?4/s specimen.It means that the stored strain energy is higher in the 150 °C and 10?4/s specimen with strong serration thanthat of 150 °C and 10?2/s specimen.This indicates that a large number of dislocations are accumulated during the deformation process due to the PLC effect and the restriction of dynamic recovery.The higher GNDs of the former is elucidated by the stronger dislocation interaction with solute or precipitate, or pile-up by PLC effect.This corresponds very well to the reversal of the trend in flow curves (Fig.4).That is, the flow stress of 10?4/s specimen was higher than that of 10?2/s specimen at the same temperature.As mentioned above, this result is related to the microstructure change during high temperature deformation due to the effect of the Nd addition.Serration in flow is observed only when sufficient long-range diffusion of obstacles such as solute or forest dislocation is involved [11,33,66-68].In this case, the movement of dislocation must be controlled by clustering as an obstacle for a certain amount of time, and the solute moves to the junction of forest and mobile dislocation to increase the strength and inhibit dislocation movement (pinning).After that, when the aging rate is slowed and the dislocation is suddenly released, stress drop occurs (unpinning), and this process is expressed as nSRS and severe serration.Depending on the strain rate and temperature, the time for dislocation movement and clustering formation and action varies.Based on these, nSRS and serration occur under conditions where dislocation and clusters can continuously interact.At high temperature, the deformation at 150 °C and 10?4/s accompanying the severe serration satisfies this condition, DSA and nSRS are induced.Thus the specimen at this condition has a relatively high GNDs at high temperature deformation compare to higher strain rate specimen.Accordingly, the misorientation degrees, in Figs.11(a) and (b), match well to the conditions of the occurrence of PLC.

    Table 4The fraction in the range of kernel average misorientation angle of each specimen corresponding to Fig.11 (in%).

    Fig.9.Inverse pole figure maps (top) and corresponding IGMA analysis results (bottom) on the uniformed area (U) of 150 °C_10?2/s specimen corresponding in Fig.6(a); (a) and (b) represent the selected grains from inverse pole figure marked as purple and blue, respectively (For interpretation of the references to color in this figure legend, the reader is referred to the web version of this article.).

    Fig.10.Equilibrium phase fraction of the (a) M1 and (b) MN11 alloys calculated using thermodynamic calculation software PANDAT.

    Fig.11.Kernel average misorientation (KAM) distribution maps (top) and the relative fraction according to the misorientation interval in each specimen(bottom); (a) 150 °C_10?2/s, (b) 150 °C_10?4/s, and (c) RT_10?4/s.

    5.Conclusion

    In this study, the texture and the mechanical properties under various temperatures and strain rates of the extruded Mg-Mn and Mg-Mn-Nd alloys were compared,and the correlation between the PLC phenomenon and the texture according to the Nd addition was analyzed.The main results of the present study are summarized below.

    (1) The addition of Nd leads to the texture weakening and occurrence of the PLC phenomenon in an extruded Mg-Mn alloy tested in uniaxial tension at ambient and 150 °C.

    (2) The PLC effect (serrated flow behavior) is significantly facilitated at 150°C and low strain rates between 10?3/s and 10?4/s.

    (3) The relationship between flow stress and strain rate is reversed at 150 °C with the occurrence of the PLC effect, i.e.the stress level rises with decreasing strain rates.

    (4) Under the condition of severe serration in the plastic flow, the deformed sample maintains the initial extrusion rare earth-type texture, which indicates that lattice rotation was suppressed during tensile deformation at 150 °C.

    (5) The decrease in high-temperature ductility despite maintaining the weakened texture and increasing the deformation temperature is due to the plastic instability associated with the occurrence of the PLC phenomenon.

    Conflict of interest

    The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

    Acknowledgment

    The authors are grateful for the financial support of German Research Foundation (DFG) (Grant Nr.Yi103/3-1 and AL1343/8-1).

    日韩成人伦理影院| 嫩草影院入口| 男女边吃奶边做爰视频| 黄片无遮挡物在线观看| 亚洲无线在线观看| 亚洲人与动物交配视频| 久久久精品大字幕| 亚洲成人av在线免费| 看非洲黑人一级黄片| 青春草亚洲视频在线观看| 麻豆成人午夜福利视频| 青春草视频在线免费观看| 99视频精品全部免费 在线| 日韩中字成人| 色播亚洲综合网| 国产一级毛片在线| av在线亚洲专区| 天天躁夜夜躁狠狠久久av| 国产高清三级在线| 联通29元200g的流量卡| 久久久久久九九精品二区国产| 菩萨蛮人人尽说江南好唐韦庄 | 久久久久久久午夜电影| 久久精品夜色国产| 久久久欧美国产精品| 国产高潮美女av| 深夜精品福利| 久久午夜亚洲精品久久| 99久久精品一区二区三区| 国产一级毛片七仙女欲春2| 久久精品国产清高在天天线| 最近手机中文字幕大全| 老女人水多毛片| 欧美最新免费一区二区三区| 国产高清激情床上av| 一区二区三区四区激情视频 | 国内揄拍国产精品人妻在线| 欧美xxxx黑人xx丫x性爽| 亚洲久久久久久中文字幕| 日韩,欧美,国产一区二区三区 | 少妇裸体淫交视频免费看高清| 99热6这里只有精品| 天堂av国产一区二区熟女人妻| 国产免费一级a男人的天堂| 亚洲精品色激情综合| 男人的好看免费观看在线视频| 精品日产1卡2卡| 免费看光身美女| 国产真实伦视频高清在线观看| 听说在线观看完整版免费高清| 99热6这里只有精品| 国产成人午夜福利电影在线观看| 亚洲欧美日韩无卡精品| 91久久精品国产一区二区成人| 欧美成人精品欧美一级黄| 少妇的逼水好多| 天天躁夜夜躁狠狠久久av| 男女边吃奶边做爰视频| 国产黄色视频一区二区在线观看 | 人体艺术视频欧美日本| 国产高清视频在线观看网站| 日韩 亚洲 欧美在线| 99久久精品一区二区三区| 天天躁夜夜躁狠狠久久av| 欧美一区二区国产精品久久精品| 非洲黑人性xxxx精品又粗又长| 少妇的逼水好多| 99国产极品粉嫩在线观看| 狂野欧美激情性xxxx在线观看| 久久精品国产亚洲网站| 亚洲国产精品合色在线| 美女黄网站色视频| 午夜精品在线福利| 免费观看精品视频网站| 国产精品福利在线免费观看| 免费看美女性在线毛片视频| 亚洲欧美精品综合久久99| 亚洲无线观看免费| avwww免费| 精品久久久久久久末码| 亚洲欧美日韩高清在线视频| 蜜臀久久99精品久久宅男| 我要看日韩黄色一级片| 亚洲人成网站在线播| 亚洲av二区三区四区| 日韩欧美一区二区三区在线观看| 日韩亚洲欧美综合| 在线播放无遮挡| 黄片无遮挡物在线观看| 最后的刺客免费高清国语| 最近最新中文字幕大全电影3| 成人特级黄色片久久久久久久| 丰满人妻一区二区三区视频av| 男人的好看免费观看在线视频| 国产成人精品一,二区 | 99久久人妻综合| 国产高清不卡午夜福利| 麻豆国产97在线/欧美| 国产黄色视频一区二区在线观看 | 日韩欧美精品v在线| а√天堂www在线а√下载| 午夜福利成人在线免费观看| 全区人妻精品视频| 中文字幕熟女人妻在线| a级毛色黄片| 成人高潮视频无遮挡免费网站| 少妇丰满av| 亚洲精品影视一区二区三区av| 日韩欧美国产在线观看| 男女啪啪激烈高潮av片| 一区二区三区四区激情视频 | 男女边吃奶边做爰视频| 夜夜夜夜夜久久久久| 国产探花极品一区二区| 日韩三级伦理在线观看| 色视频www国产| 亚洲国产精品合色在线| 精品午夜福利在线看| 国产片特级美女逼逼视频| 亚洲av中文字字幕乱码综合| 久久99蜜桃精品久久| 精品午夜福利在线看| 激情 狠狠 欧美| 日韩 亚洲 欧美在线| 久久精品国产鲁丝片午夜精品| 亚洲av中文字字幕乱码综合| 一个人看的www免费观看视频| 国产真实伦视频高清在线观看| 国产 一区精品| www.色视频.com| 亚洲av.av天堂| 国产精品精品国产色婷婷| 午夜精品在线福利| 欧美极品一区二区三区四区| 人人妻人人看人人澡| 在线a可以看的网站| 只有这里有精品99| 99热网站在线观看| 超碰av人人做人人爽久久| 好男人在线观看高清免费视频| 99九九线精品视频在线观看视频| 最近2019中文字幕mv第一页| 免费看光身美女| 99热网站在线观看| 免费在线观看成人毛片| 亚洲成人av在线免费| 哪里可以看免费的av片| 亚洲欧美精品综合久久99| 国产老妇女一区| 九色成人免费人妻av| 亚洲一区高清亚洲精品| 亚洲av中文字字幕乱码综合| 色噜噜av男人的天堂激情| 禁无遮挡网站| 欧美日韩国产亚洲二区| 亚洲精品色激情综合| 在线免费观看不下载黄p国产| 搞女人的毛片| 亚洲18禁久久av| 少妇熟女欧美另类| 国产亚洲精品久久久久久毛片| 少妇的逼好多水| 青春草国产在线视频 | 中文字幕熟女人妻在线| 国产 一区 欧美 日韩| 男女啪啪激烈高潮av片| 最后的刺客免费高清国语| 看片在线看免费视频| 亚洲欧美日韩无卡精品| 99riav亚洲国产免费| 国产欧美日韩精品一区二区| 久久精品国产自在天天线| 高清毛片免费观看视频网站| 国产免费男女视频| 国产av不卡久久| 欧美3d第一页| 亚洲欧美精品自产自拍| 国产高清有码在线观看视频| 免费人成在线观看视频色| 少妇人妻一区二区三区视频| 国产精品嫩草影院av在线观看| 亚洲欧美成人精品一区二区| 黑人高潮一二区| 麻豆精品久久久久久蜜桃| 网址你懂的国产日韩在线| 波多野结衣高清作品| 麻豆av噜噜一区二区三区| 成人亚洲欧美一区二区av| 亚洲国产欧美人成| 日本在线视频免费播放| 欧美一区二区精品小视频在线| 91在线精品国自产拍蜜月| 亚洲在线自拍视频| 精品久久久久久久久亚洲| 久久国内精品自在自线图片| 黄色配什么色好看| 亚洲精品国产成人久久av| 蜜桃久久精品国产亚洲av| 国产精品综合久久久久久久免费| 亚洲精品久久国产高清桃花| 国产精品乱码一区二三区的特点| 九九热线精品视视频播放| 国产精品久久电影中文字幕| 久久久午夜欧美精品| av卡一久久| 小蜜桃在线观看免费完整版高清| 国产精品一及| 嘟嘟电影网在线观看| 亚洲一区二区三区色噜噜| 超碰av人人做人人爽久久| 国产高清三级在线| 久久亚洲精品不卡| 99热这里只有是精品在线观看| 国产老妇女一区| av在线天堂中文字幕| 乱码一卡2卡4卡精品| 国产三级在线视频| 国产真实乱freesex| 色综合色国产| 久久综合国产亚洲精品| 99热精品在线国产| 美女黄网站色视频| 免费黄网站久久成人精品| 大型黄色视频在线免费观看| 午夜精品在线福利| 在线观看66精品国产| 亚洲欧洲日产国产| 国产 一区 欧美 日韩| 村上凉子中文字幕在线| 久久久色成人| 三级男女做爰猛烈吃奶摸视频| 成人特级av手机在线观看| 校园春色视频在线观看| 亚洲欧美日韩无卡精品| 久久人人爽人人片av| 99视频精品全部免费 在线| 国产精品女同一区二区软件| 国产色婷婷99| 久久精品国产清高在天天线| 精品99又大又爽又粗少妇毛片| 男女啪啪激烈高潮av片| 中国美女看黄片| 日韩成人伦理影院| 丰满乱子伦码专区| 黄色欧美视频在线观看| 久久精品夜夜夜夜夜久久蜜豆| 国产成人aa在线观看| 免费av不卡在线播放| 国产一区二区三区在线臀色熟女| 成人综合一区亚洲| 91麻豆精品激情在线观看国产| 婷婷色av中文字幕| 日韩精品青青久久久久久| 最后的刺客免费高清国语| 伦精品一区二区三区| АⅤ资源中文在线天堂| 99热这里只有是精品50| 色综合亚洲欧美另类图片| 麻豆精品久久久久久蜜桃| 国产午夜福利久久久久久| 91在线精品国自产拍蜜月| 少妇的逼水好多| 一本—道久久a久久精品蜜桃钙片 精品乱码久久久久久99久播 | 国产熟女欧美一区二区| 一区二区三区四区激情视频 | 欧美在线一区亚洲| 午夜视频国产福利| 99在线人妻在线中文字幕| 亚洲国产精品国产精品| 亚洲欧美日韩无卡精品| 夜夜夜夜夜久久久久| 亚洲成人久久性| 嫩草影院入口| 亚洲在久久综合| 国国产精品蜜臀av免费| 精品国内亚洲2022精品成人| 免费不卡的大黄色大毛片视频在线观看 | 菩萨蛮人人尽说江南好唐韦庄 | 日本一本二区三区精品| 我的女老师完整版在线观看| 99久久成人亚洲精品观看| 哪个播放器可以免费观看大片| 国产黄色视频一区二区在线观看 | 国产精品人妻久久久影院| 午夜精品国产一区二区电影 | 少妇人妻一区二区三区视频| 亚洲最大成人手机在线| 亚洲人成网站高清观看| 亚洲中文字幕一区二区三区有码在线看| АⅤ资源中文在线天堂| 又爽又黄无遮挡网站| 国产毛片a区久久久久| 久久99热这里只有精品18| 国产成人福利小说| 中文字幕精品亚洲无线码一区| 中国美白少妇内射xxxbb| 亚洲欧美日韩无卡精品| 99热全是精品| 久久欧美精品欧美久久欧美| 能在线免费观看的黄片| 国产一级毛片七仙女欲春2| 日韩av在线大香蕉| 伦精品一区二区三区| 综合色av麻豆| 国产又黄又爽又无遮挡在线| www.色视频.com| 久久精品久久久久久久性| 国产一级毛片七仙女欲春2| 欧美成人一区二区免费高清观看| 人人妻人人澡人人爽人人夜夜 | 精品不卡国产一区二区三区| videossex国产| 亚洲欧美日韩东京热| 国产精品女同一区二区软件| 国产成人一区二区在线| 99九九线精品视频在线观看视频| 18+在线观看网站| 中文精品一卡2卡3卡4更新| 亚洲国产精品久久男人天堂| 亚洲欧洲国产日韩| 午夜福利成人在线免费观看| 国产不卡一卡二| 久久99热6这里只有精品| 国内少妇人妻偷人精品xxx网站| 99久国产av精品国产电影| .国产精品久久| 两个人视频免费观看高清| av在线亚洲专区| 成人特级av手机在线观看| 日韩大尺度精品在线看网址| 丰满人妻一区二区三区视频av| 国产精品久久电影中文字幕| 久久精品久久久久久噜噜老黄 | 亚洲在久久综合| 中文字幕熟女人妻在线| 亚洲成av人片在线播放无| 久久久久久久午夜电影| 亚洲人成网站在线观看播放| 五月玫瑰六月丁香| 老女人水多毛片| 国产蜜桃级精品一区二区三区| 精品日产1卡2卡| 欧美日韩在线观看h| 麻豆精品久久久久久蜜桃| 日韩av不卡免费在线播放| 国产老妇伦熟女老妇高清| 不卡一级毛片| 欧美色视频一区免费| 人体艺术视频欧美日本| 99久久精品国产国产毛片| 国产精品一区二区在线观看99 | 午夜a级毛片| 成人鲁丝片一二三区免费| 91午夜精品亚洲一区二区三区| 亚洲国产精品成人久久小说 | 国产69精品久久久久777片| 大型黄色视频在线免费观看| 日本撒尿小便嘘嘘汇集6| 精品人妻偷拍中文字幕| 可以在线观看的亚洲视频| 欧美精品一区二区大全| 亚洲欧美中文字幕日韩二区| 久久热精品热| 午夜激情福利司机影院| 久久99蜜桃精品久久| 色视频www国产| 波多野结衣高清无吗| 国产精品一区www在线观看| 欧美精品一区二区大全| 简卡轻食公司| 日本免费一区二区三区高清不卡| 一进一出抽搐动态| 欧美+亚洲+日韩+国产| 久99久视频精品免费| 12—13女人毛片做爰片一| 给我免费播放毛片高清在线观看| 身体一侧抽搐| 最近的中文字幕免费完整| 国产午夜福利久久久久久| 最近手机中文字幕大全| 日韩欧美 国产精品| 久久国内精品自在自线图片| 成人毛片60女人毛片免费| 老司机影院成人| 精品一区二区三区人妻视频| 简卡轻食公司| 欧美日韩综合久久久久久| 成人特级av手机在线观看| 极品教师在线视频| 欧美+亚洲+日韩+国产| 久久午夜亚洲精品久久| 变态另类成人亚洲欧美熟女| 国产精品女同一区二区软件| 亚洲av电影不卡..在线观看| 精品熟女少妇av免费看| 成人漫画全彩无遮挡| 日本在线视频免费播放| 国产精品一区二区在线观看99 | 老师上课跳d突然被开到最大视频| 亚洲av.av天堂| 尤物成人国产欧美一区二区三区| 我的女老师完整版在线观看| 99精品在免费线老司机午夜| 精品久久久久久久久av| 国产精品人妻久久久久久| 舔av片在线| 97超碰精品成人国产| 亚洲最大成人av| 国产亚洲精品av在线| 欧美性猛交黑人性爽| 精品久久久久久久人妻蜜臀av| 最近视频中文字幕2019在线8| 国产午夜精品一二区理论片| 我要看日韩黄色一级片| 欧美激情久久久久久爽电影| 天天躁日日操中文字幕| 国产黄片美女视频| 男插女下体视频免费在线播放| 在线a可以看的网站| 亚洲va在线va天堂va国产| 午夜福利在线观看免费完整高清在 | 国产成人午夜福利电影在线观看| 我要搜黄色片| 波野结衣二区三区在线| 亚洲欧美清纯卡通| 一区二区三区高清视频在线| 日韩 亚洲 欧美在线| 2022亚洲国产成人精品| 久久久国产成人精品二区| 日本色播在线视频| 免费黄网站久久成人精品| 免费电影在线观看免费观看| 一级毛片久久久久久久久女| 色5月婷婷丁香| 国产黄片视频在线免费观看| 夫妻性生交免费视频一级片| 久久午夜亚洲精品久久| 久久精品人妻少妇| 极品教师在线视频| 丰满的人妻完整版| 啦啦啦观看免费观看视频高清| 国产av不卡久久| 日韩在线高清观看一区二区三区| 91在线精品国自产拍蜜月| 三级男女做爰猛烈吃奶摸视频| 国产精华一区二区三区| 中文字幕av成人在线电影| 51国产日韩欧美| 此物有八面人人有两片| 亚洲欧美精品综合久久99| 最新中文字幕久久久久| 中文在线观看免费www的网站| 亚洲自偷自拍三级| 啦啦啦韩国在线观看视频| 欧美性猛交黑人性爽| 国产探花极品一区二区| 亚洲精品影视一区二区三区av| 永久网站在线| 简卡轻食公司| 最好的美女福利视频网| 在线播放国产精品三级| 爱豆传媒免费全集在线观看| a级一级毛片免费在线观看| 观看美女的网站| 中文资源天堂在线| 一区二区三区四区激情视频 | 两个人的视频大全免费| 精品一区二区三区视频在线| 国产三级中文精品| 特大巨黑吊av在线直播| 99热网站在线观看| 久久这里有精品视频免费| 我要看日韩黄色一级片| 久久久久久久久久久免费av| 好男人在线观看高清免费视频| 久久欧美精品欧美久久欧美| 午夜精品国产一区二区电影 | 亚洲人成网站在线播| 日韩欧美一区二区三区在线观看| 啦啦啦韩国在线观看视频| 青青草视频在线视频观看| 国产白丝娇喘喷水9色精品| 在现免费观看毛片| 2022亚洲国产成人精品| 免费黄网站久久成人精品| 国产精品一区二区三区四区久久| 欧美日本视频| 18禁在线无遮挡免费观看视频| 身体一侧抽搐| 欧美丝袜亚洲另类| 18禁黄网站禁片免费观看直播| 亚洲av电影不卡..在线观看| 国产精品人妻久久久影院| 欧美日本视频| 一个人观看的视频www高清免费观看| 寂寞人妻少妇视频99o| 三级毛片av免费| 少妇人妻一区二区三区视频| 国产色爽女视频免费观看| 国产精品三级大全| 搞女人的毛片| 午夜精品在线福利| 日产精品乱码卡一卡2卡三| 国产91av在线免费观看| 国产亚洲91精品色在线| 国产亚洲精品av在线| 好男人视频免费观看在线| 色哟哟哟哟哟哟| a级毛色黄片| 国产精品久久久久久精品电影| 一级毛片aaaaaa免费看小| 狂野欧美激情性xxxx在线观看| 亚洲最大成人中文| 午夜免费激情av| 亚洲精品日韩在线中文字幕 | 97超视频在线观看视频| 91精品一卡2卡3卡4卡| 日韩av在线大香蕉| 午夜福利高清视频| 久久精品久久久久久久性| 九九久久精品国产亚洲av麻豆| 国产伦精品一区二区三区四那| 观看美女的网站| 成年女人看的毛片在线观看| 一级黄片播放器| 精品国产三级普通话版| 亚洲av中文字字幕乱码综合| 国产高清有码在线观看视频| 国产女主播在线喷水免费视频网站 | 国产精品三级大全| 久久久久国产网址| 久久久国产成人免费| 国产 一区精品| 国产成人精品一,二区 | 日本成人三级电影网站| 午夜激情欧美在线| avwww免费| 天堂av国产一区二区熟女人妻| 精品免费久久久久久久清纯| 不卡一级毛片| 特大巨黑吊av在线直播| 长腿黑丝高跟| 欧美激情久久久久久爽电影| 在现免费观看毛片| 少妇被粗大猛烈的视频| 男女那种视频在线观看| 听说在线观看完整版免费高清| 九九在线视频观看精品| 欧美xxxx性猛交bbbb| 成人国产麻豆网| 国产精品久久电影中文字幕| 精品国产三级普通话版| 亚洲在线自拍视频| 日本免费a在线| 三级经典国产精品| 国产精华一区二区三区| 国产高潮美女av| 啦啦啦啦在线视频资源| 亚洲国产欧洲综合997久久,| 久久久久久久久久成人| 国产片特级美女逼逼视频| 成人三级黄色视频| 成人综合一区亚洲| 色播亚洲综合网| 国产乱人视频| 国产在视频线在精品| 乱人视频在线观看| 天堂中文最新版在线下载 | 亚洲精品自拍成人| 色尼玛亚洲综合影院| 综合色av麻豆| 亚洲国产高清在线一区二区三| 啦啦啦啦在线视频资源| АⅤ资源中文在线天堂| 亚洲经典国产精华液单| 午夜激情欧美在线| 丰满人妻一区二区三区视频av| 国产成人一区二区在线| 久久久国产成人免费| avwww免费| 亚洲成av人片在线播放无| 免费观看的影片在线观看| 少妇人妻一区二区三区视频| 成人欧美大片| 少妇猛男粗大的猛烈进出视频 | 亚洲精品乱码久久久v下载方式| 亚洲无线在线观看| 99视频精品全部免费 在线| 国产单亲对白刺激| 国产亚洲91精品色在线| 亚洲av二区三区四区| 夜夜夜夜夜久久久久| 亚洲自偷自拍三级| 成年版毛片免费区| 99热6这里只有精品| 国产成年人精品一区二区| 少妇熟女aⅴ在线视频| 国产老妇伦熟女老妇高清| 男女下面进入的视频免费午夜| 亚洲精华国产精华液的使用体验 | 国产三级中文精品| 国产综合懂色| 欧美激情在线99| 亚洲精品自拍成人| 国产成人a区在线观看| 69av精品久久久久久| 夜夜看夜夜爽夜夜摸| 日韩亚洲欧美综合| 亚洲自拍偷在线| 欧美成人精品欧美一级黄| 99热网站在线观看| 波多野结衣巨乳人妻| 一级二级三级毛片免费看| 看十八女毛片水多多多| 最后的刺客免费高清国语|