• <tr id="yyy80"></tr>
  • <sup id="yyy80"></sup>
  • <tfoot id="yyy80"><noscript id="yyy80"></noscript></tfoot>
  • 99热精品在线国产_美女午夜性视频免费_国产精品国产高清国产av_av欧美777_自拍偷自拍亚洲精品老妇_亚洲熟女精品中文字幕_www日本黄色视频网_国产精品野战在线观看 ?

    Effect of cutting speed on residual stress of special coating during remanufacturing

    2015-04-22 06:24:22SUNYewang孫椰望ZHANGJiaying張甲英ZHANGZhijing張之敬XUBinshi徐濱士

    SUN Ye-wang (孫椰望), ZHANG Jia-ying(張甲英), ZHANG Zhi-jing(張之敬),XU Bin-shi(徐濱士)

    (1.School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China;2.National Key Laboratory for Remanufacturing, Academy of Armored Forces Engineering, Beijing 100072, China)

    ?

    Effect of cutting speed on residual stress of special coating during remanufacturing

    SUN Ye-wang (孫椰望), ZHANG Jia-ying(張甲英)2, ZHANG Zhi-jing(張之敬)1,XU Bin-shi(徐濱士)2

    (1.School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China;2.National Key Laboratory for Remanufacturing, Academy of Armored Forces Engineering, Beijing 100072, China)

    To study the residual stress of the special coating at different cutting speeds, the cutting of FeAlCrBSiNb coating is analyzed with the finite element method (FEM) and experiment according to the coating characteristics. The CNC machine tool is used to cut the coating and the X-ray stress equipment is used to measure the residual stress of coating. The experimental and FEM results agree with each other. Also, the residual-stress coating depth is deeper and the residual stress of the coating surface is larger with increasing cutting speed. In addition, the residual stress of the coating surface is in the suppression state affected by axial residual stress and circumferential residual stress, and the residual stress of the deeper coating is in the tensile state based on the original state of arc spraying and cutting process.

    coating cutting; arc spaying coating; residual stress; finite element method (FEM) analysis; experimental research

    Nowadays, the remanufacturing special coatings such as crystal and amorphous coating[1-2]are widely used in the remanufacture industry. In this paper, FeAlCrBSiNb as a typical amorphous coating is studied. Moreover, coating wires can vary according to the environment and the diversity of technological requirements. Therefore, remanufacturing coatings possess unique material properties (such as wear resistance, corrosion resistance, proper hardness and density, etc.). Different from other coatings, the remanufacturing typical cored wire coatings integrate with pores and micro-granules (heterogeneous particles) in the spraying process, and the remanufacturing coating thickness is general less than 1mm. So there are special requirements in the cutting tool selection and machining process of the remanufacturing typical coatings[3-5].

    In the process of coating part manufacturing, there are many spraying processes, and the coating residual stress of coating is induced by different cooling rates. The residual stress seriously affects the characteristics of coating part, such as wear, surface strength and fatigue properties[5-9]. Therefore, the analysis of the residual stress of coating for remanufacturing is becoming much more important during the coating cutting.

    In this paper, the finite element method (FEM) of cutting model and the cutting experiment are used to study the residual stress of the inhomogeneous polycrystallin FeAlCrBSiNb coating at different cutting speeds.

    1 Constitutive equations and cutting model of finite element cutting analysis

    1.1 Constitutive equations

    The cutting theory of coating for remanufacturing belongs to the classic cutting theory, and the cutting process is mainly affected by the cutting force and cutting temperature. In this paper, the Johnson-Cook cutting constitutive equation is chose to calculate the FEM model, and the equation can reflect the elastic and plastic deformation of workpiece under the condition of high temperature and high strain[6-7]. The Johnson-Cook cutting constitutive equation is shown as

    [1-[(T-Tr)/(Tm-Tr)]m]

    (1)

    During the cutting process the J-C shear failure equation is used[7,10]. The shear failure equation is based on equivalent plastic strain in the integral point value, and the unit is failure when the failure parameter reaches 1.

    1.2 FEM model of coating cutting

    The FEM model of coating cutting is based on the structural characteristics of the coating part, and the structure should be simplified in the FEM model. The section structure of FeAlCrBSiNb coating part is shown in Fig. 1, which consists of coating, substrate (45 steel), interface, heterogeneous particles and aperture gap. The coating and substrate are bound by physical binding strength of about 50 MPa.

    Fig.1 Section of FeAlCrBSiNb coating part

    Fig. 2 shows the FEM coating cutting geometry model. The thickness is 0.7 mm according to remanufacturing spraying layer thickness, which mainly includes the thickness of chip layer 0.2 mm (cutting depth) and non-chip coating 0.5 mm. The coating cutting length is 3mm. The FEM tool model is according to the experimental physical vapor deposition (PVD) alloy tool with structural rake angle of 15°and flank angle of 6°.

    Fig.2 FEM cutting geometry model

    According to the bonding strength (about 50 MPa) of the coating and substrate and the motion characteristic of workpiece and tool in the cutting process, the boundary constraint model is established as shown in Fig. 3. In the model, the FEM coating lower edge is defined as pre-stress 50 MPa, the cutting velocity is defined as the tool, and the coating edge is defined as fixed boundary on the both sides of non-chip layer region. In the meshing process, coupling aspect of cutting force and temperature and the FEM calculation time are taken into account, the chip layer and cutting transition layer is precision mesh, and the small effect zone affected by the cutting process is gradient mesh.

    Fig.3 Pre-stress mesh modal of FEM coating cutting

    Furthermore, according to Figs.1-2, the coating heterogeneous particles and aperture gap are simplified in the FEM model; and FEM calculation is based on the following assumptions: ① Tool is rigid, and only its friction and temperature conduction are considered. ② The microstructure and chemical change of material are ignored. ③ The machining material is isotropic. ④ The vibration of cutting tool and workpiece are ignored. The main physical parameters of FEM model is according to Tab. 1 and experimental parameters.

    Tab.1 Characteristic of FeAlCrBSiNb

    2 Applicability analysis of FEM coating cutting

    In order to reveal applicability of the FEM coating cutting process,tchip morphology and cutting force are analyzed with the FEM. The J-C equation of FEM is a numerical model of thermal coupling force, so the FEM analysis considers cutting temperature, and the FEM and experimental residual stress analysis are all coupled with the cutting force and heat. Meanwhile, it shows that the impact of low cutting on the residual stress is much smaller than the impact of cutting force in the cutting process, so this paper focuses on the cutting force.

    Fig.5 Coating chip formation (vc=80 m/min,f=0.09 mm/r,ap=0.2 mm)

    The experimental platform of cutting coating study is as shown in Fig. 4. The experimental platform includes Kistler piezoelectric dynamometer for cutting force measuring, PVD alloy tool with angle 15° and X-ray residual stress equipment.

    Fig.4 FeAlCrBSiNb coating cutting experiment

    The cutting parameters of experiment and FEM analysis are based on FeAlCrBSiNb coating material properties (Tab. 1) and the laboratory coating cutting data[6,8]. FEM analysis and cutting experimental cutting speedvcinclude 60 m/min, 70 m/min and 80 m/min, and the cutting feed is 0.09 mm/r. The results are shown in Figs. 5-6.

    Fig. 5 shows that the chip formation of FEM and experimental analysis are both serrated shearing chip; also, the chip dimension is similar. As shown in Fig. 5a, the chip is about 1.5 mm based on Fig.2, and the chip lengthLbetween the adjacent cracks is about 0.25 mm. As shown in Fig.5b, the chip lengthlis about 0.26 mm. The result indicates that the FEM cutting model used in this paper is able to analyze chip serrated crack characteristic of FeAlCrBSiNb coating.

    Fig. 6 shows the coating cutting force comparison of FEM and experiment, and the analysis results of two methods have the similar trend. Furthermore, it reveals that the cutting force does not increase as the cutting speed increases. The main sources of error in the two methods are due to the FEM cutting assumption and the experimental measurement error, and the numerical error value is about 30 N. The analysis shows that the FEM cutting model is suitable for the mechanics characteristic of coating cutting process.

    Fig.6 Comparison of FEM and experiment cutting force (f=0.09 mm/r,ap=0.2 mm)

    The comparison analysis of Fig. 5 and Fig. 6 shows that the FEM cutting model is able to explain the characteristics of coating cutting mechanics and chip formation, and the results match the theory foundation for the residual stress analysis of coating cutting.

    3 Results and discussion

    3.1 Mechanism analysis of coating cutting

    Coating cutting mechanism is shown in Fig.7, which is based on the principle of orthogonal cutting[6,11]and the structural characteristics of coating workpiece. The coating cutting process is mainly influenced by the shear slip, cutting friction and temperature. There is non-uniform thermo-mechanical coupling function in the stress field.

    According to the chip formation analysis in Fig.6 and Fig.7, coating cutting deformation zone is divided into three main areas. The Ⅰ zone is cutting plastic deformation zone, and chip is mainly affected by shear stress. When the shear stress reaches the coating yield strength, the chip begins to fracture. In addition,Φis shear angle,OAis chip emerging slip line, andOCis the chip termination slip line. The Ⅱ zone is the chip deformation zone, and the chip is mainly affected by the rake face pressureFnand frictionFf. Also, the chip deformation and motion affect cutting plastic deformation process. The Ⅲ zone is machining surface affected by pressureFNand frictionFf2of flank tool; moreover, the zone directly affects the quality and residual stress of the machined surface.

    Fig.7 Schematic drawing of cutting process for remanufactures

    In short, from chip emerging to separation, coating cutting residual stress is mainly affected by cutting force in the process of cutting and the influence of pressureFNand frictionFf2of flank tool on the machining surface. As a result, due to the factors in the process of cutting, the elastic and plastic stress of the machining coating surface and subsurface inevitably alternate. In order to further reveal the residual stress characteristic of coating cutting, the FEM and experiment methods are used to study the coating cutting, and the results are shown in Fig.8 and Fig.9.

    Fig.8 FEM residual stress analysis of FeAlCrBSiNb coating

    Fig.9 Experimental residual stress of the coating

    3.2 Analysis of FEM residual stress

    Fig.8a shows FEM coating residual stress image and acquisition data. The result shows that the residual stress along the deep direction (Y) is not a consistent distribution, but there is a similar trend. Data acquisition is based on the cutting process region in Fig.5a, and the region is chose to avoid much influence of cutting process and boundary constraint. The data of the selected elements are acquired from top to bottom, and the data contains the axial residual stress (S11) inXdirection and the circumferential residual stress inYdirection (S22). The acquisition data is shown in Fig.8b and Fig.8c; in addition, the positive data is tensile stress, and the negative data is compressive stress.

    According to the circumferential residual stress in Fig.8b at different cutting speeds, there are several main features as follows.

    ① The results show that the depth of residual stress change distribution is 120-140 μm, which indicates that the depth of mechanical influence on the coating cutting is about 140 μm. Furthermore, there is a decreasing trend of residual stress along the coating depth.

    ② At different speeds, distribution of the residual stress has similar trend-decrease; then it tends to be stable. In addition, the residual stress changes from tensile stress to compressive stress along the coating depth; then, it changes from compressive stress to the initial state. Furthermore, it shows that the maximum stress and stress distribution depth do not change linearly with the cutting speed increasing. When cutting speed is 70 m/min, the maximum compressive residual stress value is 110 MPa, and its distribution depth is 35 μm which is the shallowest. However, when the cutting speeds are 60 m/min and 80 m/min, the maximum compressive residual stress values is gradually decreasing.

    ③ With the increase of cutting speed, the residual stress of coating surface gradually increases, and the stress is all residual tensile stress.

    Fig.8c reveals the axial tensile stress and compressive stress changes in the cutting velocity direction (X) at different cutting speeds. The surface residual stress increases with the speed increasing, but the increase is not linear. In addition, the process of residual stress change reflects that the stress changes from maximum surface compressive stress to tensile stress along the depth direction. Moreover, Fig.8c reveals that depth of coating residual stress reduces with increase of cutting speed.

    In Fig.8, there are curve cross phenomena. It is mainly due to the rates of residual stress are different from the cutting zone to the initial state based on the different cutting conditions. The larger coating residual stress transition area is, the clearer the amplitude variation is. However, there is residual stress pulse in local area, and it is mainly due to the different residual stress distribution and the cutting coating non-uniformity. Further, it illustrates that the residual stress in the coating integrates with diversity characteristics in the local area.

    3.3 Analysis of experimental residual stress

    In order to study the coating cutting residual stress further, the coating cutting is analyzed by the experiment with the same parameters of FEM analysis, and the results are shown in Fig.9.

    It shows that the coating original circumferential residual stress is tensile stress about 50 MPa as shown in Fig.9a. Fig.9b shows the original axial residual stress of coating surface is compressive stress, but the other zone is tensile stress about 70 MPa. Especially, there is visible change in the coating zone within 120 μm, indicating that the cutting stress has large influence on the coating residual stress in the cutting effect zone.

    Comparison of Fig.8 with Fig.9 shows that there are similar characteristics of FEM and experimental residual stress analysis, and the FEM and X-ray stress equipment are able to study the coating cutting residual stress. Of course, there are special characteristics in the two methods, and there are several differences in the results, and the numerical difference of the local coating zone is due to the instrument error and the FEM assumptions in the calculation.

    3.4 Thermal-mechanical effect on coating residual stress

    FeAlCrBSiNb coating cutting process is integrated with cutting force and heat. The research shows that cutting force could induce tensile stress and compressive stress in the coating cutting process. Furthermore, when the residual tensile stress is larger than the compressive stress, the coating is tensile stress; on the contrary, it is compressive stress. Fig.8 and Fig.9 show that the coating surface circumferential residual stress is main tensile stress, and the axial residual stress is compressive stress. In addition, the compressive stress value is much greater than the tensile stress value, so the coating cutting surface residual stress is in the compressive stress state.

    Moreover, because the “plastic bulge” affected by the initial spraying stress is greater than “thermal expansion” caused by the thermal stress, the spraying coating is in tensile stress state at certain depth[3, 5, 12]. Due to the original residual stress of arc spraying coating and the coating cutting residual stress, the residual stress of machined coating is changed from compressive stress to tensile stress along the coating depth. According to Fig.6, Fig.8b and Fig.9a, with the increase of cutting speed, the cutting force decreases, which causes the plastic deformation zone decrease along the coating depth direction; as a result, the rate of coating residual stress translated to the initial tensile stress is much faster.

    Remanufacturing coating cutting residual stress primarily affects the joint components surface, combined with coating cutting residual stress analysis and coating process characteristics, the Second Project of the engine 5C components remanufacturing applications of the First Automobile Works (FAW ) has been carried out on September 23, 2013 in the National Key Laboratory for Remanufacturing. Especially, the tentative processes of rough machining, preheating treatment stress, semi-finishing and finishing machining were made in the crankshaft machining process; then, on the basis of suitable process , it is expected that more than 2 000 damaged crankshafts will be repaired a year, indicating a more than 10 million yuan (each crankshaft ¥5 000) business per year.

    4 Conclusions

    The FEM model proposed in this paper is able to analyze the coating serrated shearing chip formation, and the FEM cutting force is in accordance with the experimental value in 30 N compensation case.

    The depth of coating residual stress affected by the cutting process is within 0.2 mm, and with the increase of cutting speed, the depth caused by cutting force and heat decreases, resulting in increase of the surface residual stress.

    Because cutting residual compressive stress of coating surface is larger than tensile stress, the machined coating surface has compressive stress. In addition, affected by the arc spraying thermal residual stress and cutting residual stress, the residual stress of coating is in the tensile residual stress state under 0.2 mm of machined coating surface.

    The results show that there is optimal speed range of cutting speed influence on coating residual stress. In view of the FeAlCrBSiNb coating, when the cutting speed is 70-80 m/min, the influence depth of cutting residual stress is shallow, and the stress amplitude is stabile.

    [1] Xu Binshi, Zhu Shaohua. Theories and technologies on surface engineering[M]. Beijing: National Defense Industry Press, 2010: 4. (in Chinese)

    [2] Wang Min, Xu Binshi, Dong Shiyun, et al. Experimental investigation into the effect of cutting parameters on cutting forces in turning of Fe-based amorphous overlay for remanufacture [J]. International Journal of Advanced Manufacturing Technology, 2013, 65(5): 735-743.

    [3] Chen Yongxiong, Liang Xiubing, Liu Yan, et al. Prediction of residual stresses in thermally sprayed steel coatings considering the phase transformation effect[J]. Materials and Design, 2010, 31: 3852-3858.

    [4] Zhang X C, Xu B S, Wang H D, et al. Thermo-mechanical integrity of coatings with residual stresses [C]//Fracture Mechanics 2004-Symbosium of Environment Effects on Fracture and Damage, Huangshan, China, 2004.

    [5] Cheng Jiangbo, Liang Xiubing, Chen Yongxiong, et al. Residual stress in electric arc sprayed coatings for remanufacturing [J]. Transactions of the China Welding Institution, 2008(29): 17-20. (in Chinese)

    [6] Chen Riyao. Principles of machining [M]. Beijing: China Machine Press, 2012, 12, 1. (in Chinese)

    [7] Sun Yazhou, Liu Haitao, Lu Zesheng. Finite element simulation and experimental research of residual stress in the cutting based on the coupled thermo-mechanical model [J]. Chinese Journal of Mechanical Engineering, 2011, 47(1): 187-193. (in Chinese)

    [8] Wang Suyu, Ai Xing, Zhao Jun, et al. Effect of cutting speed on residual stress of workpiece by using FEM [J]. Machine Tool Technology, 2005, 39(9):33-36. (in Chinese)

    [9] Xin Min, Xie Lijing, Wang Xibin, et al. Study on the surface residual stress of high hardness and strength alloy steel in high speed milling [J]. Transactions of Beijing Institute of Technology, 2010, 30(1):19-23. (in Chinese)

    [10] Tan Mengyang. Residual stress control research on machined surface for pre-stress cutting [D]. Guangzhou: South China University of Technology, 2012: 5. (in Chinese)

    [11] Zhang Y C, Mabrouki T, Nelias D, et al. Chip formation in orthogonal cutting considering interface limiting shear stress and damage evolution based on fracture energy approach [J]. Finite Elements in Analysis and Design, 2011,47(7):850-863.

    [12] Chen Yongxiong, Liang Xiubing, Liu Yan, et al. Finite element modeling of coating formation and transient heat transfer in the electric arc spray process [J]. International Journal of Heat and Mass Transfer, 2010, 53: 2012-2021.

    (Edited by Cai Jianying)

    10.15918/j.jbit1004-0579.201524.0209

    TH 112 Document code: A Article ID: 1004- 0579(2015)02- 0194- 07

    Received 2013- 07- 04

    E-mail: sun_yewang@163.com

    午夜福利欧美成人| 国产精品久久久久久亚洲av鲁大| 免费在线观看视频国产中文字幕亚洲| 中出人妻视频一区二区| 国产午夜福利久久久久久| 99久久99久久久精品蜜桃| 中文字幕最新亚洲高清| 天堂影院成人在线观看| 欧美成人免费av一区二区三区| 老司机午夜十八禁免费视频| 日韩大码丰满熟妇| 欧美在线一区亚洲| 亚洲欧美一区二区三区黑人| 18禁美女被吸乳视频| 精品国产乱码久久久久久男人| 91麻豆精品激情在线观看国产| 亚洲九九香蕉| 老鸭窝网址在线观看| 亚洲人成电影免费在线| 欧美黄色淫秽网站| 最近最新中文字幕大全电影3| 欧美性长视频在线观看| 三级国产精品欧美在线观看 | 亚洲av中文字字幕乱码综合| 男男h啪啪无遮挡| 欧美性长视频在线观看| 91字幕亚洲| 免费在线观看完整版高清| 九九热线精品视视频播放| 老鸭窝网址在线观看| 久久这里只有精品19| 无人区码免费观看不卡| 青草久久国产| 黄片大片在线免费观看| 一本一本综合久久| 真人一进一出gif抽搐免费| 成人av在线播放网站| 亚洲人与动物交配视频| 日本一区二区免费在线视频| 免费在线观看亚洲国产| 欧美3d第一页| 又爽又黄无遮挡网站| 中文字幕最新亚洲高清| 丁香六月欧美| 成人一区二区视频在线观看| 精品国产乱子伦一区二区三区| 制服人妻中文乱码| 欧美日韩亚洲国产一区二区在线观看| 日本在线视频免费播放| 在线播放国产精品三级| 九色国产91popny在线| 国内久久婷婷六月综合欲色啪| 观看免费一级毛片| 精品无人区乱码1区二区| av片东京热男人的天堂| 久久精品国产99精品国产亚洲性色| 国产精品 欧美亚洲| 亚洲色图av天堂| 国产又色又爽无遮挡免费看| 99国产精品一区二区蜜桃av| 国产又黄又爽又无遮挡在线| 欧美成人午夜精品| 国产精品久久久久久精品电影| 久久亚洲真实| 久久久久久久久免费视频了| 一区二区三区高清视频在线| 久久久国产精品麻豆| 在线观看免费午夜福利视频| 特级一级黄色大片| 亚洲美女视频黄频| 两性夫妻黄色片| 欧美大码av| 变态另类丝袜制服| 国产一区二区激情短视频| 十八禁网站免费在线| 午夜精品一区二区三区免费看| 亚洲成人久久爱视频| 可以在线观看的亚洲视频| 婷婷丁香在线五月| 亚洲国产中文字幕在线视频| 国产精品永久免费网站| 国产99久久九九免费精品| 两个人看的免费小视频| 观看免费一级毛片| 波多野结衣巨乳人妻| 国产激情偷乱视频一区二区| 男男h啪啪无遮挡| 看片在线看免费视频| 成人永久免费在线观看视频| 欧美精品亚洲一区二区| 老汉色∧v一级毛片| 久久欧美精品欧美久久欧美| 久久99热这里只有精品18| 一级片免费观看大全| 老司机福利观看| 曰老女人黄片| 五月玫瑰六月丁香| 中文字幕精品亚洲无线码一区| 在线观看舔阴道视频| 欧美av亚洲av综合av国产av| 国产精品 国内视频| 高清在线国产一区| 少妇粗大呻吟视频| 国产亚洲精品久久久久5区| 欧美一级毛片孕妇| 一区二区三区激情视频| 亚洲性夜色夜夜综合| 99久久国产精品久久久| 国产日本99.免费观看| 三级男女做爰猛烈吃奶摸视频| 手机成人av网站| 久久久久国产精品人妻aⅴ院| 亚洲午夜精品一区,二区,三区| 久久精品国产综合久久久| 看片在线看免费视频| 亚洲av片天天在线观看| 久久精品夜夜夜夜夜久久蜜豆 | 久久久久国产一级毛片高清牌| 亚洲国产精品合色在线| 男女床上黄色一级片免费看| 18禁黄网站禁片午夜丰满| 亚洲午夜理论影院| 婷婷六月久久综合丁香| 一级作爱视频免费观看| 在线观看舔阴道视频| 99re在线观看精品视频| 一边摸一边抽搐一进一小说| 日日摸夜夜添夜夜添小说| 神马国产精品三级电影在线观看 | 婷婷亚洲欧美| 日韩欧美一区二区三区在线观看| 亚洲一卡2卡3卡4卡5卡精品中文| 欧美精品啪啪一区二区三区| 亚洲激情在线av| 99在线视频只有这里精品首页| 精品高清国产在线一区| 久久久国产欧美日韩av| 欧美成人一区二区免费高清观看 | 在线观看www视频免费| 久久香蕉国产精品| 日韩欧美在线二视频| 欧美三级亚洲精品| 精品国产乱码久久久久久男人| 亚洲国产中文字幕在线视频| 在线观看www视频免费| 午夜免费成人在线视频| 日韩欧美在线二视频| 成年免费大片在线观看| 级片在线观看| 精品福利观看| 999精品在线视频| 精品国产美女av久久久久小说| 最近视频中文字幕2019在线8| 久久久久久久久久黄片| 国产成年人精品一区二区| 一个人免费在线观看电影 | 99久久无色码亚洲精品果冻| 亚洲aⅴ乱码一区二区在线播放 | 免费看a级黄色片| 美女黄网站色视频| 俄罗斯特黄特色一大片| 两性夫妻黄色片| 精品久久蜜臀av无| 99热这里只有是精品50| 天天躁夜夜躁狠狠躁躁| 久久人人精品亚洲av| 中文字幕最新亚洲高清| 窝窝影院91人妻| 少妇熟女aⅴ在线视频| 黄色成人免费大全| 手机成人av网站| 亚洲专区中文字幕在线| 日韩成人在线观看一区二区三区| 88av欧美| videosex国产| 中文字幕熟女人妻在线| 精品久久久久久久末码| 可以在线观看的亚洲视频| 在线观看日韩欧美| 最新在线观看一区二区三区| 成年免费大片在线观看| 精品欧美一区二区三区在线| 成人欧美大片| 亚洲成人免费电影在线观看| 国产亚洲精品久久久久5区| 欧美高清成人免费视频www| 搡老岳熟女国产| 亚洲精品久久国产高清桃花| 特级一级黄色大片| av有码第一页| 伦理电影免费视频| 国产亚洲精品第一综合不卡| 国产熟女午夜一区二区三区| 老司机在亚洲福利影院| 欧美性猛交╳xxx乱大交人| 蜜桃久久精品国产亚洲av| 老汉色∧v一级毛片| 国产亚洲精品久久久久5区| 久久久久精品国产欧美久久久| 午夜视频精品福利| 老鸭窝网址在线观看| 国产av麻豆久久久久久久| 搡老岳熟女国产| 国产亚洲av嫩草精品影院| 亚洲午夜理论影院| 免费高清视频大片| 国产激情久久老熟女| 麻豆久久精品国产亚洲av| 国内毛片毛片毛片毛片毛片| 亚洲欧美日韩高清在线视频| 国产主播在线观看一区二区| 欧美3d第一页| 精品电影一区二区在线| 麻豆av在线久日| 亚洲中文日韩欧美视频| 国产欧美日韩一区二区三| 狂野欧美白嫩少妇大欣赏| 国内精品一区二区在线观看| 欧美日韩中文字幕国产精品一区二区三区| 国内久久婷婷六月综合欲色啪| 欧美+亚洲+日韩+国产| 一个人观看的视频www高清免费观看 | 好男人在线观看高清免费视频| 超碰成人久久| 琪琪午夜伦伦电影理论片6080| 欧美中文综合在线视频| 国产野战对白在线观看| 黄片大片在线免费观看| 老司机在亚洲福利影院| 88av欧美| 别揉我奶头~嗯~啊~动态视频| e午夜精品久久久久久久| 观看免费一级毛片| av免费在线观看网站| 国产三级中文精品| 婷婷六月久久综合丁香| 欧美日韩乱码在线| 很黄的视频免费| 啦啦啦韩国在线观看视频| 黑人巨大精品欧美一区二区mp4| 亚洲真实伦在线观看| 亚洲精品色激情综合| 18禁裸乳无遮挡免费网站照片| 少妇的丰满在线观看| 亚洲精品av麻豆狂野| 亚洲中文字幕日韩| 国产精品av视频在线免费观看| 性色av乱码一区二区三区2| 国产精华一区二区三区| 精品久久久久久久久久免费视频| 天天躁夜夜躁狠狠躁躁| 国产精华一区二区三区| av免费在线观看网站| 丝袜美腿诱惑在线| 中文字幕久久专区| 美女黄网站色视频| 精品日产1卡2卡| 好男人电影高清在线观看| 中亚洲国语对白在线视频| 日韩欧美在线乱码| 久久精品影院6| 国产激情久久老熟女| 国产三级中文精品| 亚洲人成电影免费在线| 不卡一级毛片| 十八禁人妻一区二区| 国产免费男女视频| 久久中文字幕人妻熟女| 日韩欧美在线乱码| 亚洲精品国产精品久久久不卡| 国产久久久一区二区三区| av中文乱码字幕在线| 两性夫妻黄色片| 老熟妇乱子伦视频在线观看| 99国产综合亚洲精品| 夜夜躁狠狠躁天天躁| www日本黄色视频网| 非洲黑人性xxxx精品又粗又长| 精品少妇一区二区三区视频日本电影| 亚洲精品中文字幕一二三四区| 可以在线观看毛片的网站| 婷婷六月久久综合丁香| 亚洲精品国产一区二区精华液| 午夜福利在线在线| 在线观看免费午夜福利视频| 免费在线观看影片大全网站| 男人的好看免费观看在线视频 | 亚洲精华国产精华精| 久久精品国产综合久久久| 国产高清激情床上av| 欧美精品亚洲一区二区| 亚洲成人精品中文字幕电影| 91av网站免费观看| 狂野欧美激情性xxxx| 亚洲一区中文字幕在线| 久久中文看片网| 中国美女看黄片| 午夜精品一区二区三区免费看| 一区二区三区高清视频在线| 制服诱惑二区| 亚洲国产高清在线一区二区三| 国产高清有码在线观看视频 | 老司机靠b影院| 草草在线视频免费看| 亚洲专区字幕在线| 久久久久亚洲av毛片大全| 国产一区二区三区在线臀色熟女| 美女 人体艺术 gogo| 久久久精品大字幕| av福利片在线观看| 亚洲精品久久成人aⅴ小说| 嫁个100分男人电影在线观看| 搞女人的毛片| 国产精品av久久久久免费| 国产精品电影一区二区三区| 老汉色av国产亚洲站长工具| 夜夜躁狠狠躁天天躁| 午夜免费观看网址| 欧美大码av| 99久久精品热视频| 日本三级黄在线观看| 啦啦啦免费观看视频1| 夜夜夜夜夜久久久久| 国产爱豆传媒在线观看 | 国产精品亚洲一级av第二区| www.www免费av| 精品福利观看| 中亚洲国语对白在线视频| 成人高潮视频无遮挡免费网站| 听说在线观看完整版免费高清| 啦啦啦韩国在线观看视频| 亚洲精品色激情综合| 天堂影院成人在线观看| 国产精品,欧美在线| 国产久久久一区二区三区| 日韩 欧美 亚洲 中文字幕| 又爽又黄无遮挡网站| 女人高潮潮喷娇喘18禁视频| av视频在线观看入口| 日日摸夜夜添夜夜添小说| 免费高清视频大片| 一级毛片精品| 国产精品九九99| 人妻丰满熟妇av一区二区三区| 亚洲激情在线av| 成人18禁在线播放| 国产av一区二区精品久久| 午夜福利成人在线免费观看| 欧美黑人精品巨大| 亚洲国产精品久久男人天堂| 国产欧美日韩一区二区三| 亚洲国产精品久久男人天堂| 国产欧美日韩一区二区三| svipshipincom国产片| 亚洲片人在线观看| 一卡2卡三卡四卡精品乱码亚洲| 精品久久久久久,| e午夜精品久久久久久久| av天堂在线播放| 国内精品久久久久久久电影| 亚洲成人精品中文字幕电影| 色综合欧美亚洲国产小说| 巨乳人妻的诱惑在线观看| 免费在线观看亚洲国产| 亚洲自拍偷在线| 桃色一区二区三区在线观看| 丁香欧美五月| 欧美极品一区二区三区四区| 一区福利在线观看| 国内久久婷婷六月综合欲色啪| 草草在线视频免费看| 日本三级黄在线观看| 久久精品aⅴ一区二区三区四区| 国产激情久久老熟女| 国内揄拍国产精品人妻在线| 国产片内射在线| 男女做爰动态图高潮gif福利片| 亚洲国产精品久久男人天堂| 国产精品免费一区二区三区在线| 国内精品久久久久精免费| 中文字幕人妻丝袜一区二区| 日日摸夜夜添夜夜添小说| 欧美一区二区国产精品久久精品 | 久久精品国产清高在天天线| xxx96com| 亚洲精品国产精品久久久不卡| 窝窝影院91人妻| 亚洲国产欧美人成| 一级毛片女人18水好多| 精品久久久久久,| 一本久久中文字幕| 欧美高清成人免费视频www| 国产一区二区在线观看日韩 | 国内久久婷婷六月综合欲色啪| 精品少妇一区二区三区视频日本电影| 亚洲无线在线观看| 成人欧美大片| 国产精品精品国产色婷婷| 欧美高清成人免费视频www| 国产精品自产拍在线观看55亚洲| 亚洲va日本ⅴa欧美va伊人久久| 精品免费久久久久久久清纯| 激情在线观看视频在线高清| 久久精品成人免费网站| 999久久久精品免费观看国产| 国产av又大| 久久久久久九九精品二区国产 | 国产一区在线观看成人免费| 校园春色视频在线观看| 久久99热这里只有精品18| 中文字幕最新亚洲高清| 哪里可以看免费的av片| 黑人操中国人逼视频| av在线天堂中文字幕| 欧美 亚洲 国产 日韩一| 岛国在线免费视频观看| 精品少妇一区二区三区视频日本电影| 午夜精品在线福利| 好男人电影高清在线观看| 日本撒尿小便嘘嘘汇集6| 亚洲av成人不卡在线观看播放网| 可以免费在线观看a视频的电影网站| 午夜影院日韩av| 制服诱惑二区| 国产一区二区三区视频了| 1024手机看黄色片| av中文乱码字幕在线| 国产v大片淫在线免费观看| 国产一区二区在线观看日韩 | 高清毛片免费观看视频网站| 亚洲狠狠婷婷综合久久图片| 国产亚洲精品综合一区在线观看 | 亚洲中文字幕日韩| 久久久国产成人免费| 又粗又爽又猛毛片免费看| 亚洲一区高清亚洲精品| 黄色女人牲交| 怎么达到女性高潮| 91成年电影在线观看| 久久久久免费精品人妻一区二区| 久久精品国产亚洲av高清一级| av免费在线观看网站| 亚洲成av人片免费观看| 日韩欧美国产一区二区入口| 老司机午夜福利在线观看视频| 99re在线观看精品视频| xxx96com| 亚洲狠狠婷婷综合久久图片| 国产精品一区二区三区四区免费观看 | 搡老岳熟女国产| 日本在线视频免费播放| АⅤ资源中文在线天堂| 女人爽到高潮嗷嗷叫在线视频| 久久久久久久精品吃奶| 国产午夜福利久久久久久| 18禁黄网站禁片午夜丰满| 日韩欧美精品v在线| 欧美中文综合在线视频| 久久精品影院6| 在线观看舔阴道视频| 人成视频在线观看免费观看| 夜夜看夜夜爽夜夜摸| 99精品久久久久人妻精品| 人人妻人人澡欧美一区二区| 亚洲avbb在线观看| 美女高潮喷水抽搐中文字幕| 久久精品国产综合久久久| 69av精品久久久久久| 一边摸一边做爽爽视频免费| 国产麻豆成人av免费视频| 国产在线观看jvid| www.熟女人妻精品国产| 一区福利在线观看| 精品午夜福利视频在线观看一区| 色哟哟哟哟哟哟| 精品免费久久久久久久清纯| 欧美最黄视频在线播放免费| 亚洲美女视频黄频| 欧美中文日本在线观看视频| 我的老师免费观看完整版| 制服丝袜大香蕉在线| 国产人伦9x9x在线观看| 国产高清激情床上av| xxx96com| 国产精品av久久久久免费| 手机成人av网站| 一本一本综合久久| 日韩欧美精品v在线| 天堂影院成人在线观看| 90打野战视频偷拍视频| 777久久人妻少妇嫩草av网站| 欧美色视频一区免费| 村上凉子中文字幕在线| 最新美女视频免费是黄的| 亚洲无线在线观看| 国语自产精品视频在线第100页| 1024手机看黄色片| 搡老岳熟女国产| 国产在线精品亚洲第一网站| 欧美日韩亚洲综合一区二区三区_| 国产乱人伦免费视频| 一级作爱视频免费观看| 国产一区在线观看成人免费| 一级毛片女人18水好多| 欧美成人性av电影在线观看| 在线观看www视频免费| 97超级碰碰碰精品色视频在线观看| 国产高清激情床上av| 成人欧美大片| 亚洲国产精品成人综合色| 两个人的视频大全免费| 少妇的丰满在线观看| 亚洲av美国av| 亚洲自偷自拍图片 自拍| 这个男人来自地球电影免费观看| 午夜福利在线在线| 亚洲欧洲精品一区二区精品久久久| 国产黄a三级三级三级人| 免费在线观看视频国产中文字幕亚洲| 两性夫妻黄色片| 精品久久久久久,| xxx96com| 国产黄色小视频在线观看| 在线观看www视频免费| 国产69精品久久久久777片 | 日本一二三区视频观看| 婷婷精品国产亚洲av在线| 高清在线国产一区| 亚洲 国产 在线| 亚洲avbb在线观看| 国产亚洲欧美在线一区二区| 国语自产精品视频在线第100页| 操出白浆在线播放| 色噜噜av男人的天堂激情| 国产精品一区二区免费欧美| 国产亚洲精品久久久久5区| 亚洲精品在线美女| 欧美色欧美亚洲另类二区| 黄色女人牲交| 黑人操中国人逼视频| 十八禁人妻一区二区| 久久人人精品亚洲av| 日本一本二区三区精品| 香蕉丝袜av| 国产99白浆流出| 女人被狂操c到高潮| 黄片小视频在线播放| 韩国av一区二区三区四区| 黄片大片在线免费观看| 少妇人妻一区二区三区视频| 国产精品一区二区免费欧美| 亚洲欧美一区二区三区黑人| 午夜视频精品福利| 久久伊人香网站| 视频区欧美日本亚洲| 在线a可以看的网站| 非洲黑人性xxxx精品又粗又长| 日韩欧美一区二区三区在线观看| 国产亚洲精品av在线| 99riav亚洲国产免费| 午夜福利在线在线| 最近最新中文字幕大全电影3| 久久中文字幕人妻熟女| 亚洲中文字幕一区二区三区有码在线看 | 午夜成年电影在线免费观看| 欧美性猛交黑人性爽| 一级黄色大片毛片| 成人国语在线视频| 99在线人妻在线中文字幕| 亚洲色图av天堂| 国内精品久久久久久久电影| 亚洲,欧美精品.| 日韩国内少妇激情av| 亚洲人成电影免费在线| 在线永久观看黄色视频| 国产亚洲精品av在线| 香蕉国产在线看| 在线观看一区二区三区| 午夜日韩欧美国产| 青草久久国产| 日韩精品免费视频一区二区三区| 久久久久久久久中文| 午夜福利视频1000在线观看| 欧美在线黄色| 午夜日韩欧美国产| 两性夫妻黄色片| av欧美777| 亚洲国产日韩欧美精品在线观看 | 日韩av在线大香蕉| 神马国产精品三级电影在线观看 | 国产精品精品国产色婷婷| 亚洲国产精品合色在线| 在线观看午夜福利视频| 国产精品免费视频内射| 午夜福利视频1000在线观看| 国产三级中文精品| 精品久久蜜臀av无| 国产欧美日韩一区二区三| 中文字幕久久专区| av在线天堂中文字幕| 午夜激情av网站| 久久久久久大精品| 久9热在线精品视频| 国产三级中文精品| 亚洲第一欧美日韩一区二区三区| 久久这里只有精品中国| 国产探花在线观看一区二区| 亚洲九九香蕉| 在线观看免费视频日本深夜| x7x7x7水蜜桃| 婷婷六月久久综合丁香| 一级毛片女人18水好多| 俄罗斯特黄特色一大片| 精品福利观看| 别揉我奶头~嗯~啊~动态视频|